- 02 7月, 2018 2 次提交
-
-
由 Xiaolin Zhang 提交于
changed gvt display transcode DDI mode from DP_SST to DVI to address below calltrace issue during guest booting up which is caused by zero dotclock initial value with DP_SST mode. transcode DVI mode emulation also align with native with DP connection. [drm:drm_calc_timestamping_constants] ERROR crtc 41: Can't calculate constants, dotclock = 0! WARNING: at drivers/gpu/drm/drm_vblank.c:620 drm_calc_vbltimestamp_from_scanoutpos Call Trace: ? drm_calc_timestamping_constants+0x144/0x150 [drm] drm_get_last_vbltimestamp+0x54/0x90 [drm] drm_reset_vblank_timestamp+0x59/0xd0 [drm] drm_crtc_vblank_on+0x7b/0xd0 [drm] intel_modeset_setup_hw_state+0xb67/0xfd0 [i915] ? gen2_read32+0x110/0x110 [i915] ? drm_modeset_lock+0x30/0xa0 [drm] intel_modeset_init+0x794/0x19d0 [i915] ? intel_setup_gmbus+0x232/0x2e0 [i915] i915_driver_load+0xb4a/0xf40 [i915] Signed-off-by: NXiaolin Zhang <xiaolin.zhang@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Zhao Yan 提交于
when guest writes ggtt entries, it could write 8 bytes a time if gtt_entry_size is 8. But, qemu could split the 8 bytes into 2 consecutive 4-byte writes. If each 4-byte partial write could trigger a host ggtt write, it is very possible that a wrong combination is written to the host ggtt. E.g. the higher 4 bytes is the old value, but the lower 4 bytes is the new value, and this 8-byte combination is wrong but written to the ggtt, thus causing bugs. To handle this condition, we just record the first 4-byte write, then wait until the second 4-byte write comes and write the combined 64-bit data to host ggtt table. To save memory space and to spot partial write as early as possible, we don't keep this information for every ggtt index. Instread, we just record the last ggtt write position, and assume the two 4-byte writes come in consecutively for each vgpu. This assumption is right based on the characteristic of ggtt entry which stores memory address. When gtt_entry_size is 8, the guest memory physical address should be 64 bits, so any sane guest driver should write 8-byte long data at a time, so 2 consecutive 4-byte writes at the same ggtt index should be trapped in gvt. v2: when incomplete ggtt entry write is located, e.g. 1. guest only writes 4 bytes at a ggtt offset and no long writes the rest 4 bytes. 2. guest writes 4 bytes of a ggtt offset, then write at other ggtt offsets, then return back to write the left 4 bytes of the first ggtt offset. add error handling logic to remap host entry to scratch page, and mark guest virtual ggtt entry as not present. (zhenyu wang) Signed-off-by: NZhao Yan <yan.y.zhao@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
- 19 6月, 2018 8 次提交
-
-
由 Kenneth Graunke 提交于
The SF and clipper units mishandle the provoking vertex in some cases, which can cause misrendering with shaders that use flat shaded inputs. There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN (for the clipper) that work around the issue. These registers are unfortunately not part of the logical context (even the power context), and so we must reload them every time we start executing in a context. Bugzilla: https://bugs.freedesktop.org/103047Signed-off-by: NKenneth Graunke <kenneth@whitecape.org> Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180615190605.16238-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: stable@vger.kernel.org (cherry picked from commit b77422f8) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Mika Kuoppala 提交于
If client is smart or lucky enough to create a new context after each hang, our context banning mechanism will never catch up, and as a result of that it will be saved from client banning. This can result in a never ending streak of gpu hangs caused by bad or malicious client, preventing access from other legit gpu clients. Fix this by always incrementing per client ban score if it hangs in short successions regardless of context ban scoring. The exception are non bannable contexts. They remain detached from client ban scoring mechanism. v2: xchg timestamp, tidyup (Chris) v3: comment, bannable & banned together (Chris) Fixes: b083a087 ("drm/i915: Add per client max context ban limit") Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180615104429.31477-1-mika.kuoppala@linux.intel.com (cherry picked from commit 14921f3c) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Ville Syrjälä 提交于
While Bspec doesn't list a specific sequence for turning off the DP port on g4x we are getting an underrun if the port is disabled in the .disable() hook. Looks like the pipe stops when the port stops, and by that time the plane disable may not have completed yet. Also the plane(s) seem to end up in some wonky state when this happens as they also signal another underrun immediately after we turn them back on during the next enable sequence. We could add a vblank wait in .disable() to avoid wedging the planes, but I assume we're still tripping up the pipe in some way. So it seems better to me to just follow the ILK+ sequence and turn off the DP port in .post_disable() instead. This sequence doesn't seem to suffer from this problem. Could be it was always the intended sequence for DP and the gen4 bspec was just never updated to include it. Originally we used the bad sequence even on ilk+, but I changed that in commit 08aff3fe ("drm/i915: Move DP port disable to post_disable for pch platforms") as it was causing issues on those platforms as well. I left out g4x then only because I didn't have the hardware to test it. Now that I do it's fairly clear that the ilk+ sequence is also the right choice for g4x. v2: Fix whitespace fail (Jani) Mention the ilk+ commit (Jani) Cc: stable@vger.kernel.org Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com> (cherry picked from commit 51a9f6df) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Ville Syrjälä 提交于
Looks like interlaced DP output doesn't work on g4x either. Not all that surprising considering we already established that interlaced DP output is busted on VLV/CHV. Cc: stable@vger.kernel.org Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: NJani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-1-ville.syrjala@linux.intel.com (cherry picked from commit 929168c5) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Ville Syrjälä 提交于
On i965/g4x IIR is edge triggered. So in order for IIR to notice that there is still a pending interrupt we have to force and edge in ISR. For the ISR/IIR pipe event bits we can do that by temporarily clearing all the PIPESTAT enable bits when we ack the status bits. This will force the ISR pipe event bit low, and it can then go back high when we restore the PIPESTAT enable bits. This avoids the following race: 1. stat = read(PIPESTAT) 2. an enabled PIPESTAT status bit goes high 3. write(PIPESTAT, enable|stat); 4. write(IIR, PIPE_EVENT) The end result is IIR==0 and ISR!=0. This can lead to nasty vblank wait/flip_done timeouts if another interrupt source doesn't trick us into looking at the PIPESTAT status bits despite the IIR PIPE_EVENT bit being low. Before i965 IIR was level triggered so this problem can't actually happen there. And curiously VLV/CHV went back to the level triggered scheme as well. But for simplicity we'll use the same i965/g4x compatible code for all platforms. Cc: stable@vger.kernel.org Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106033 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105225 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106030Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk> (cherry picked from commit 132c27c9) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Ville Syrjälä 提交于
When encountering a connector with the scaling mode property both intel and modesetting ddxs sometimes add tons of DBLSCAN modes to the output's mode list. The idea presumably being that since the output will be going through the panel fitter anyway we can pretend to use any kind of mode. Sadly that means we can't reject user modes with the DBLSCAN flag until we know whether we're going to be using the panel's native mode or the user mode directly. Doing otherwise means X clients using xf86vidmode/xrandr will get a protocol error (and often self terminate as a result) when the kernel refuses to use the requested mode with the DBLSCAN flag. To undo the regression we'll move the DBLSCAN checks into the connector->mode_valid() and encoder->compute_config() hooks. Cc: stable@vger.kernel.org Cc: Vito Caputo <vcaputo@pengaru.com> Reported-by: NVito Caputo <vcaputo@pengaru.com> Fixes: e995ca0b ("drm/i915: Provide a device level .mode_valid() hook") References: https://lkml.org/lkml/2018/5/21/715Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804Tested-by: NArkadiusz Miskiewicz <arekm@maven.pl> (cherry picked from commit e4dd27aa) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Chris Wilson 提交于
On allocation error, do not jump to the unwind handler that tries to free the error pointer. Reported-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com> Fixes: a89d1f92 ("drm/i915: Split i915_gem_timeline into individual timelines") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180611153332.14824-1-chris@chris-wilson.co.uk (cherry picked from commit 467d3578) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Chris Wilson 提交于
We special case the position of the batch within the GTT to prevent negative self-relocation deltas from underflowing. However, that restriction is being applied after a trial pin of the batch in its current position. Thus we are not rejecting an invalid location if the batch has been used before, leading to an assertion if we happen to need to rearrange the entire payload. In the worst case, this may cause a GPU hang on gen7 or perhaps missing state. References: https://bugs.freedesktop.org/show_bug.cgi?id=105720 Fixes: 2889caa9 ("drm/i915: Eliminate lots of iterations over the execobjects array") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Martin Peres <martin.peres@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180610194325.13467-2-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com> (cherry picked from commit 746c8f14) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
- 13 6月, 2018 2 次提交
-
-
由 Kees Cook 提交于
The vzalloc() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: vzalloc(a * b) with: vzalloc(array_size(a, b)) as well as handling cases of: vzalloc(a * b * c) with: vzalloc(array3_size(a, b, c)) This does, however, attempt to ignore constant size factors like: vzalloc(4 * 1024) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( vzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | vzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( vzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | vzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | vzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | vzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | vzalloc( - sizeof(u8) * COUNT + COUNT , ...) | vzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | vzalloc( - sizeof(char) * COUNT + COUNT , ...) | vzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( vzalloc( - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | vzalloc( - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ vzalloc( - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( vzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( vzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | vzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | vzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | vzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | vzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | vzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( vzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( vzalloc(C1 * C2 * C3, ...) | vzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression E1, E2; constant C1, C2; @@ ( vzalloc(C1 * C2, ...) | vzalloc( - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
- 07 6月, 2018 3 次提交
-
-
由 Mahesh Kumar 提交于
Do not update number of enabled dbuf slices in dev_priv struct until we actually enable/disable dbuf slice in hw. This is leading to never updating dbuf slices and resulting in DBuf slice mismatch warning. Fixes: aa9664ff ("drm/i915/icl: Enable 2nd DBuf slice only when needed") Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180517132626.5885-1-mahesh1.kumar@intel.com (cherry picked from commit 6ceb7277) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Mahesh Kumar 提交于
All connectors may not have best_encoder attached, so don't dereference encoder pointer for each connector. Fixes: c27e917e ("drm/i915/icl: add basic support for the ICL clocks") Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180525155238.7054-1-lucas.demarchi@intel.com (cherry picked from commit c46ef57d) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Ville Syrjälä 提交于
We already handle the color encoding mode properly. Remove the broken NV12 special case. Cc: Vidya Srinivas <vidya.srinivas@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: 8ed30ab6 ("drm/i915: Enable YUV to RGB for Gen10 in Plane Ctrl Reg") Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180521185613.5097-1-ville.syrjala@linux.intel.comReviewed-By: NVidya Srinivas <vidya.srinivas@intel.com> (cherry picked from commit 012d79e6) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
- 31 5月, 2018 3 次提交
-
-
由 Chris Wilson 提交于
Since we use i915_gem_find_active_request() from inside intel_engine_dump() and may call that at any time, we do not guarantee that the engine is paused nor that the signal kthreads and irq handler are suspended, so we cannot assert that the breadcrumb doesn't advance and that the irq hasn't happened on another CPU signaling the request we believe to be idle. The second assert removed (that request->engine == engine) remains valid, but is now more rigorously checked during retirement. Fixes: f636edb2 ("drm/i915: Make i915_engine_info pretty printer to standalone") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180529132922.6831-1-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com> (cherry picked from commit cc7cc534) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Jani Nikula 提交于
This reverts commit dc911f5b. Per the report, no matter what display mode you select with xrandr, the i915 driver will always select the alternate fixed mode. For the reporter this means that the display will always run at 40Hz which is quite annoying. This may be due to the mode comparison. But there are some other potential issues. The choice of alt_fixed_mode seems dubious. It's the first non-preferred mode, but there are no guarantees that the only difference would be refresh rate. Similarly, there may be more than one preferred mode in the probed modes list, and the commit changes the preferred mode selection to choose the last one on the list instead of the first. (Note that the probed modes list is the raw, unfiltered, unsorted list of modes from drm_add_edid_modes(), not the pretty result after a drm_helper_probe_single_connector_modes() call.) Finally, we already have eerily similar code in place to find the downclock mode for DRRS that seems like could be reused here. Back to the drawing board. Note: This is a hand-crafted revert due to conflicts. If it fails to backport, please just try reverting the original commit directly. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105469Reported-by: NRune Petersen <rune@megahurts.dk> Reported-by: NMark Spencer <n7u4722r35@ynzlx.anonbox.net> Fixes: dc911f5b ("drm/i915/edp: Allow alternate fixed mode for eDP if available.") Cc: Clint Taylor <clinton.a.taylor@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jim Bride <jim.bride@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v4.14+ Signed-off-by: NJani Nikula <jani.nikula@intel.com> Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180516080110.22770-1-jani.nikula@intel.com (cherry picked from commit d93fa1b4) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Chris Wilson 提交于
Make sure that when we don't have any scheduler attributes for the request, the string is terminated. Fixes: 247870ac ("drm/i915: Build request info on stack before printk") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180517152824.11619-1-chris@chris-wilson.co.uk (cherry picked from commit 96d4f03c) Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
- 29 5月, 2018 1 次提交
-
-
由 Chris Wilson 提交于
nospec quite reasonably asserts that it will never be used with an index larger than unsigned long (that being the largest possibly index into an C array). However, our ubi uses the convention of u64 for any large integer, running afoul of the assertion on 32b. Reduce our index to an unsigned long, checking for type overflow first. drivers/gpu/drm/i915/i915_query.c: In function 'i915_query_ioctl': include/linux/compiler.h:339:38: error: call to '__compiletime_assert_119' declared with attribute error: BUILD_BUG_ON failed: sizeof(_s) > sizeof(long) Reported-by: kbuild-all@01.org Fixes: 84b510e2 ("drm/i915/query: Protect tainted function pointer lookup") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180522121018.15199-1-chris@chris-wilson.co.uk (cherry picked from commit a33b1dc8) Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
- 28 5月, 2018 3 次提交
-
-
由 Chris Wilson 提交于
Smatch identifies i915_query_ioctl() as being a potential victim of Spectre due to its use of a tainted user index into a function pointer array. Use array_index_nospec() to defang the user index before using it to lookup the function pointer. Fixes: a446ae2c ("drm/i915: add query uAPI") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180521210530.26008-1-chris@chris-wilson.co.uk (cherry picked from commit 84b510e2) Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
由 Chris Wilson 提交于
Delay registering ourselves with the acpi lid notification mechanism until we are registering the connectors after initialisation is complete. This prevents a possibility of trying to handle the lid notification before we are ready with the danger of chasing uninitialised function pointers. BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 IP: (null) PGD 0 P4D 0 Oops: 0010 [#1] PREEMPT SMP PTI Modules linked in: arc4(+) iwldvm(+) i915(+) mac80211 i2c_algo_bit coretemp mei_wdt iwlwifi drm_kms_helper kvm_intel wmi_bmof iTCO_wdt iTCO_vendor_support kvm snd_hda_codec_conexant snd_hda_codec_generic drm psmouse cfg80211 irqbypass input_leds pcspkr i2c_i801 snd_hda_intel snd_hda_codec thinkpad_acpi snd_hda_core mei_me lpc_ich snd_hwdep e1000e wmi nvram snd_pcm mei snd_timer shpchp ptp pps_core rfkill syscopyarea snd intel_agp sysfillrect intel_gtt soundcore sysimgblt battery led_class fb_sys_fops ac rtc_cmos agpgart evdev mac_hid acpi_cpufreq ip_tables x_tables ext4 crc32c_generic crc16 mbcache jbd2 fscrypto crypto_simd glue_helper cryptd aes_x86_64 xts algif_skcipher af_alg dm_crypt dm_mod sd_mod uas usb_storage serio_raw atkbd libps2 ahci libahci uhci_hcd libata scsi_mod ehci_pci ehci_hcd usbcore usb_common i8042 serio CPU: 1 PID: 378 Comm: systemd-logind Not tainted 4.16.8-1-ARCH #1 Hardware name: LENOVO 7454CTO/7454CTO, BIOS 6DET72WW (3.22 ) 10/25/2012 RIP: 0010: (null) RSP: 0018:ffffaf4580c33a18 EFLAGS: 00010287 RAX: 0000000000000000 RBX: ffff947533558000 RCX: 000000000000003e RDX: ffffffffc0aa80c0 RSI: ffffaf4580c33a3c RDI: ffff947534e4c000 RBP: ffff947533558338 R08: ffff947534598930 R09: ffffffffc0a928b1 R10: ffffd8f181d5fd40 R11: 0000000000000000 R12: ffffffffc0a928b1 R13: ffff947533558368 R14: ffffffffc0a928a9 R15: ffff947534e4c000 FS: 00007f3dc4ddb940(0000) GS:ffff947539280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000006e214000 CR4: 00000000000406e0 Call Trace: ? intel_modeset_setup_hw_state+0x385/0xf60 [i915] ? __intel_display_resume+0x1e/0xc0 [i915] ? intel_display_resume+0xcc/0x120 [i915] ? intel_lid_notify+0xbc/0xc0 [i915] ? notifier_call_chain+0x47/0x70 ? blocking_notifier_call_chain+0x3e/0x60 ? acpi_lid_notify_state+0x8f/0x1d0 ? acpi_lid_update_state+0x49/0x70 ? acpi_lid_input_open+0x60/0x90 ? input_open_device+0x5d/0xa0 ? evdev_open+0x1ba/0x1e0 [evdev] ? chrdev_open+0xa3/0x1b0 ? cdev_put.part.0+0x20/0x20 ? do_dentry_open+0x14c/0x300 ? path_openat+0x30c/0x1240 ? current_time+0x16/0x60 ? do_filp_open+0x93/0x100 ? __check_object_size+0xfb/0x180 ? do_sys_open+0x186/0x210 ? do_syscall_64+0x74/0x190 ? entry_SYSCALL_64_after_hwframe+0x3d/0xa2 Code: Bad RIP value. RIP: (null) RSP: ffffaf4580c33a18 CR2: 0000000000000000 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106559 Fixes: c1c7af60 ("drm/i915: force mode set at lid open time") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: NJani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180518074840.16194-1-chris@chris-wilson.co.uk Cc: stable@vger.kernel.org (cherry picked from commit e578a570) Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
由 Ondrej Zary 提交于
Radiant P845 does not have LVDS, only VGA. Cc: stable@vger.kernel.org Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105468Signed-off-by: NOndrej Zary <linux@rainbow-software.org> Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180309222204.4771-1-linux@rainbow-software.org (cherry picked from commit 7f7105f9) Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
- 16 5月, 2018 1 次提交
-
-
由 Michel Thierry 提交于
Factor in clear values wherever required while updating destination min/max. References: HSDES#1604444184 Signed-off-by: NMichel Thierry <michel.thierry@intel.com> Cc: mesa-dev@lists.freedesktop.org Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Oscar Mateo <oscar.mateo@intel.com> Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180510200708.18097-1-michel.thierry@intel.com Cc: stable@vger.kernel.org Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180514165445.9198-1-michel.thierry@intel.com (backported from commit 0c79f9cb) Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
- 14 5月, 2018 10 次提交
-
-
由 Jani Nikula 提交于
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
-
由 Chris Wilson 提交于
We assume that the CSB is written using the normal ringbuffer coherency protocols, as outlined in kernel/events/ring_buffer.c: * (HW) (DRIVER) * * if (LOAD ->data_tail) { LOAD ->data_head * (A) smp_rmb() (C) * STORE $data LOAD $data * smp_wmb() (B) smp_mb() (D) * STORE ->data_head STORE ->data_tail * } So we assume that the HW fulfils its ordering requirements (B), and so we should use a complimentary rmb (C) to ensure that our read of its WRITE pointer is completed before we start accessing the data. The final mb (D) is implied by the uncached mmio we perform to inform the HW of our READ pointer. References: https://bugs.freedesktop.org/show_bug.cgi?id=105064 References: https://bugs.freedesktop.org/show_bug.cgi?id=105888 References: https://bugs.freedesktop.org/show_bug.cgi?id=106185 Fixes: 767a983a ("drm/i915/execlists: Read the context-status HEAD from the HWSP") References: 61bf9719 ("drm/i915/cnl: Use mmio access to context status buffer") Suggested-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Rafael Antognolli <rafael.antognolli@intel.com> Cc: Michel Thierry <michel.thierry@intel.com> Cc: Timo Aaltonen <tjaalton@ubuntu.com> Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com> Acked-by: NMichel Thierry <michel.thierry@intel.com> Acked-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180511121147.31915-1-chris@chris-wilson.co.uk (cherry picked from commit 77dfedb5) Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
由 Matthew Auld 提交于
Operating on a zero sized GEM userptr object will lead to explosions. Fixes: 5cc9ed4b ("drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl") Testcase: igt/gem_userptr_blits/input-checking Signed-off-by: NMatthew Auld <matthew.auld@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk> Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180502195021.30900-1-matthew.auld@intel.com (cherry picked from commit c11c7bfd) Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
由 Chris Wilson 提交于
When we process the outstanding requests upon banning a context, we need to acquire both the engine and the client's timeline, nesting the locks. This requires explicit markup as the two timelines are now of the same class, since commit a89d1f92 ("drm/i915: Split i915_gem_timeline into individual timelines"). Testcase: igt/gem_eio/banned Fixes: a89d1f92 ("drm/i915: Split i915_gem_timeline into individual timelines") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Michel Thierry <michel.thierry@intel.com> Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180512084957.9829-1-chris@chris-wilson.co.uk
-
由 Chris Wilson 提交于
The original switch to use CSB from the HWSP was plagued by the effect of read ordering on VT-d; we would read the WRITE pointer from the HWSP before it had completed writing the CSB contents. The mystery comes down to the lack of rmb() for correct ordering with respect to the writes from HW, and with that resolved we can remove the VT-d special casing. Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Michel Thierry <michel.thierry@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180511121147.31915-3-chris@chris-wilson.co.ukTested-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
-
由 Weinan Li 提交于
This reverts commit 11474e90. There are issues which will block the host preemption before, instead of disabling it use one workaround "setting max priority for gvt context" to avoid the gvt context be preempted by the host. Now the issues have been cleared, so revert this patch to enable host preemption. v2: - refine description(Zhenyu) Signed-off-by: NWeinan Li <weinan.z.li@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
-
由 Zhao Yan 提交于
the cmd_reg_handler() is called by cmds LRM, PIPE_CTRL, SRM... for LRM, SRM, we cannot get write data in a simple way. On other side, the force_to_nonpriv reigsters will only be written in LRI in current drivers. so we don't want to bother the handler to handle those memory access cmds, just leave a print message here. Signed-off-by: NZhao Yan <yan.y.zhao@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Zhao Yan 提交于
Return error will cause vm hang and enter failsafe mode. However, we don't want that happen on detecting an wrong force_to_nonpriv register write. Therefore, we just omit the wrong write or patch it to default value. v2: only return 0 on detecting lri write of registers outside whitelist, but still return error on other error conditions. (zhenyu wang) Signed-off-by: NZhao Yan <yan.y.zhao@intel.com> Reviewed-by: NZhang Yulei <yulei.zhang@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Zhao Yan 提交于
Each ring has a NOPID register and currently they are regarded as default value of force_to_nonpriv registers in guest drivers Signed-off-by: NZhao Yan <yan.y.zhao@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Changbin Du 提交于
The disable_warn_untrack never prevent gvt from printing untracked mmio errors. We were disturbed by this error storm and the fix is just adding them to the list with no essential new change. This message is only useful for enabling new platform during developing process. So lower the message level to debug and then remove disable_warn_untrack. Signed-off-by: NChangbin Du <changbin.du@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
- 13 5月, 2018 2 次提交
-
-
由 Michel Thierry 提交于
Factor in clear values wherever required while updating destination min/max. References: HSDES#1604444184 Signed-off-by: NMichel Thierry <michel.thierry@intel.com> Cc: mesa-dev@lists.freedesktop.org Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Oscar Mateo <oscar.mateo@intel.com> Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180510200708.18097-1-michel.thierry@intel.com Cc: stable@vger.kernel.org
-
由 Matthew Auld 提交于
We write all 4K page entries, even when using 64K pages. In order to verify that the HW isn't cheating by using the 4K PTE instead of the 64K PTE, we want to remove all the surplus entries. If the HW skipped the 64K PTE, it will read/write into the scratch page instead - which we detect as missing results during selftests. v2: much improved commentary (Chris) Signed-off-by: NMatthew Auld <matthew.auld@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Changbin Du <changbin.du@intel.com> Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk> Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180511095140.25590-1-matthew.auld@intel.com
-
- 12 5月, 2018 1 次提交
-
-
由 Chris Wilson 提交于
Before we unpin the buffer used for OA reports and return it to the system, we need to be sure that the HW has finished writing into it. For lack of a better idea, poll OACONTROL to check it is switched off. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106379Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Matthew Auld <matthew.auld@intel.com> Reviewed-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com> Tested-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180511135207.12880-1-chris@chris-wilson.co.uk
-
- 11 5月, 2018 4 次提交
-
-
由 Chris Wilson 提交于
In the previous patch (to include a rmb() after readig the CSB WRITE pointer from the HWSP) we believe we have fixed the underlying bug, and so can re-enable using the HWSP on Cannolake. This reverts commit 61bf9719 ("drm/i915/cnl: Use mmio access to context status buffer"). References: https://bugs.freedesktop.org/show_bug.cgi?id=105888 References: https://bugs.freedesktop.org/show_bug.cgi?id=106185 References: 61bf9719 ("drm/i915/cnl: Use mmio access to context status buffer") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Rafael Antognolli <rafael.antognolli@intel.com> Cc: Michel Thierry <michel.thierry@intel.com> Cc: Timo Aaltonen <tjaalton@ubuntu.com> Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com> Acked-by: NMichel Thierry <michel.thierry@intel.com> Acked-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180511121147.31915-2-chris@chris-wilson.co.uk
-
由 Chris Wilson 提交于
We assume that the CSB is written using the normal ringbuffer coherency protocols, as outlined in kernel/events/ring_buffer.c: * (HW) (DRIVER) * * if (LOAD ->data_tail) { LOAD ->data_head * (A) smp_rmb() (C) * STORE $data LOAD $data * smp_wmb() (B) smp_mb() (D) * STORE ->data_head STORE ->data_tail * } So we assume that the HW fulfils its ordering requirements (B), and so we should use a complimentary rmb (C) to ensure that our read of its WRITE pointer is completed before we start accessing the data. The final mb (D) is implied by the uncached mmio we perform to inform the HW of our READ pointer. References: https://bugs.freedesktop.org/show_bug.cgi?id=105064 References: https://bugs.freedesktop.org/show_bug.cgi?id=105888 References: https://bugs.freedesktop.org/show_bug.cgi?id=106185 Fixes: 767a983a ("drm/i915/execlists: Read the context-status HEAD from the HWSP") References: 61bf9719 ("drm/i915/cnl: Use mmio access to context status buffer") Suggested-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Rafael Antognolli <rafael.antognolli@intel.com> Cc: Michel Thierry <michel.thierry@intel.com> Cc: Timo Aaltonen <tjaalton@ubuntu.com> Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com> Acked-by: NMichel Thierry <michel.thierry@intel.com> Acked-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180511121147.31915-1-chris@chris-wilson.co.uk
-
由 Oscar Mateo 提交于
Avoids a hang during soft reset. v2: Rebased on top of the WA refactoring v3: Added References (Mika) v4: - Rebased - C, not lisp (Chris) - Which steppings affected by this are not clear. For the moment, apply unconditionally as per the BSpec (Mika) - Add reference to another HSD also related References: HSDES#1405476379 References: HSDES#2006612137 Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: NOscar Mateo <oscar.mateo@intel.com> Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-14-git-send-email-oscar.mateo@intel.com
-
由 Oscar Mateo 提交于
Disable CGPSF unit clock gating to prevent an issue. v2: Rebased on top of the WA refactoring v3: Added References (Mika) v4: - Rebased - C, not lisp (Chris) - Remove unintentional whitespaces (Mika) - Fixed in C0 (Mika) References: HSDES#1406838659 Signed-off-by: NOscar Mateo <oscar.mateo@intel.com> Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-13-git-send-email-oscar.mateo@intel.com
-