- 18 6月, 2011 23 次提交
-
-
由 Emmanuel Grumbach 提交于
iwl_bus will represent a bus, and iwl_bus_ops all the operations that can be done on this bus. For the moment only set_prv_data is implemented. More to come... Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Emmanuel Grumbach 提交于
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Emmanuel Grumbach 提交于
Move some PCI functionality to the new iwl_pci.[ch] files: * the PCI_DEVICE_TABLE * the pci_driver struct definition * the PCI probe / remove functions * the PCI suspend / resume functions All these functions are now split: the trigger comes from the PCI layer which calls to the bus generic code located in the other files. This is the beginning only. There are still a lot of PCI related code needs to be gathered. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Emmanuel Grumbach 提交于
It is superfluous to disable the interrupts after we reset the NIC. The only entity that could enable the interrupts after the NIC is reset is the driver. So remove this pointless action. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Flush command can target specified interface or all interfaces Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
When issue tx flush, also consider PAN Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
After driver split, no need to make indirect call to txfifo flush function Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Rafał Miłecki 提交于
Turning it on is always done between reading PHY version and radio version, so it was easy to find it in MMIO dumps from ndiswrapper. Turning off is done by writing different values to the same registers. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Every PHY has some specific bit used for reading radio regs. Analyze of MMIO dumps from BCM4331 and ndiswrapper has shown it is 0x200 for HT. radio_read(0x037f) -> 0x0073 radio_write(0x017f) <- 0x0072 Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Pavel Roskin 提交于
Signed-off-by: NPavel Roskin <proski@gnu.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Pavel Roskin 提交于
Move an extern variable declaration to a header file. Prefix all functions with "ath5k_". Make ath5k_intr() static. Remove unneeded forward declarations. Remove pointless "extern" in a function declaration. Signed-off-by: NPavel Roskin <proski@gnu.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Pavel Roskin 提交于
Signed-off-by: NPavel Roskin <proski@gnu.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Pavel Roskin 提交于
Signed-off-by: NPavel Roskin <proski@gnu.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
during suspend/resume ath9k_stop will always call ath_radio_disable which will inturn call ath9k_hw_configpcipowersave, so no need to call it explicitly in ath9k_stop Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
Patch 7f1f9742 "iwlegacy: refactor iwl4965_mac_channel_switch" reversed a test and also it changed a spin_lock_irq() to spin_lock(). I assume the spin_lock change was a mistake because the unlock was left as spin_unlock_irq(). Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
Add few debug messages for some of the possible scenarios where we can detect PAPRD failures. this will help us to be sure that we had really enabled PAPRD Cc: susinder@qca.qualcomm.com Cc: senthilb@qca.qualcomm.com Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
It is always "y" for now, b43 will not compile without CONFIG_SSB yet. This is just a first step of dropping SSB dependency. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Nikanth Karthikesan 提交于
if_spi: Fix compilation warning - unused variable 'spi' drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_init_card’: drivers/net/wireless/libertas/if_spi.c:1035: warning: unused variable ‘spi’ The variable is used only in a macro which uses the args only for DEBUG builds. Remove the 'spi' variable completely. Signed-off-by: NNikanth Karthikesan <nikanth@google.com> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
This is totally broken plus we do not have specs for HT PHY yet. Just introduce place for writing driver if we discover anything. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Eliad Peller 提交于
When suspending, __ieee80211_suspend() calls ieee80211_scan_cancel(), which will only cancel sw scan. In order to cancel hw scan, the low-level driver has to cancel it in the suspend() callback. however, this is too late, as a new scan_work will be enqueued (while the driver is going into suspend). Add a new cancel_hw_scan() callback, asking the driver to cancel an active hw scan, and call it in ieee80211_scan_cancel(). Signed-off-by: NEliad Peller <eliad@wizery.com> Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Connor Hansen 提交于
warning message drivers/ssb/driver_chipcommon_pmu.c: In function ssb_pmu_resources_init drivers/ssb/driver_chipcommon_pmu.c:420:15: warning: updown_tab_size may be used uninitilized in this function. updown_tab_size and depend_tab_size may not be set in the bus->chip_id switch statement, so set to 0 by default to avoid using uninitialized stack space. Signed-off-by: NConnor Hansen <cmdkhh@gmail.com> Signed-off-by: NMichael Buesch <m@bues.ch> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Paul Stewart 提交于
Trigger connection monitor on resume from suspend. Since we have been sleeping, there is reason to suspect that we might not still be associated. The speed of detecting loss of {connection,authentication} is worth the cost of the small additional traffic at resume. Signed-off-by: NPaul Stewart <pstew@chromium.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 6月, 2011 17 次提交
-
-
由 Wey-Yi Guy 提交于
Check EEPROM for multiple contexts support Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Make sure when we say 11n enable, we really support it. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Multiple places have similar code to construct calib header. Merge into single inline function. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
No functional changes, just group similar defines together Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Temperature location in EEPROM is generic to all devices Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Remove both IWL_DEBUG_TXPOWER and IWL_DEBUG_NOTIF, not used. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Instead use generic IWL_DEBUG_INFO, use IWL_DEBUG_FW for uCode related stuffs. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Instead of IWL_DEBUG_POWER, IWL_DEBUG_TEMP should be used for temperature related debug messages Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Adding dedicated debug message for coex related activities Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Replace IWL_DEBUG_AP with IWL_DEBUG_COEX for debug COEX related stuffs Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Instead of having the separated define, use the sku capabilities in EEPROM Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Add define for band capabilities in EEPROM Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Johannes Berg 提交于
The ucode subtypes keep changing, and there's no particular reason to be checking them (other than a paranoid sanity check). Since the numbers are also in conflict between different ucode images now, simply don't check them any more and rely on the images being built correctly. Also, to indicate that, rename the constants and the enum, moving it to a different file. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Move no_sleep_autoadjust module parameter into iwlagn_mod_params structure along with all the other iwlagn module parameters Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Move led_mode module parameter into iwlagn_mod_params structure along with all the other iwlagn module parameters Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Move bt_coex_active module parameter into iwlagn_mod_params structure along with all the other iwlagn module parameters Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
For testmode trace function, huge amout of data need to pass to userspace. Use the build-in nl80211 dumpt it function Require nl80211 testmode dumpit support patch. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-