Since AR9287 v1.0 was never sold (and the initvals removed), its revision
checks can be simplified similar to AR9280
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since AR9285 v1.0 and v1.1 were never sold (and the initvals removed),
its revision checks can be simplified similar to AR9280
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since AR9280 v1.0 was never sold (and the initvals removed), v1.0 specific
revision checks can be removed and the 'v2.0 or later' check can be
simplified to a check for AR9280 or later.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixing up a merge issue / concurrent development:

Remove unneeded ath_crypt_caps flags, as per "ath9k_hw: remove useless hw
capability flags" (364734fa), but set the
AESCCM flag for ath9k. common ath code still needs a flag for this because
there is ath5k hardware which can't do AES in hardware.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use key management functions which have been moved to ath/key.c and remove
ath9k copies of these functions and other now unused definitions.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To reduce scan time, enable fastcc for AR7010

(fastcc == fast channel change -- JWL)
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For AR9271 chips, if partial reset is done while scanning, the cycpwrThr1
will be set to maximum. This causes the degrade in DL throughput.
So restore the ANI registers to default during the partial reset.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is enabled only for ar9285.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.

This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.

For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.

For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

https://bugzilla.kernel.org/show_bug.cgi?id=16476Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Cc: stable@kernel.org

If the receive path gets stuck, a full hardware reset is necessary to
recover from it. If this happens during a scan, the whole scan might fail,
as each channel change bypasses the full reset sequence.
Fix this by resetting the fast channel change flag if stopping the
receive path fails.

This will reduce the number of error messages that look like this:
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.

Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.

This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NBjörn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Without this we could start trying to work with the device without
it being fully functional yet and loose some packets upon resume.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This can be useful during testing of new ASPM tweaks which often
have to be done through the PCI Serializer-Deserializer (SERDES).

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LowPower array writes disables the PLL when ASPM is enabled.
The host driver makes quite a few calls to ath9k_hw_configpcipowersave()
and these same calls also need to ensure the PLL is off when they issue
it.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The AR_WA register should not be read when in sleep state so
add a variable we can stash its value into for when we need
to set it. Additionally the AR_WA_D3_TO_L1_DISABLE_REAL
(bit 16) needs to be removed.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This capability check is no longer used, so it can be removed along with
the now-obsolete ath9k_hw_getcapability function.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver always sets this to enabled, but this can be simplified with
a small change to ah->sta_id1_defaults instead.
This change also removes the now-obsolete ath9k_hw_setcapability function.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is only used as a workaround for an issue in one specific hw revision.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TKIP MIC support is always enabled anyway.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace calls that read this capability with accesses to ath9k_hw's
regulatory data.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All of the ciphers that are tested for are always supported
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw_setmac() only copies the mac address it is called with into
common->macaddr, yet in all call sites, the supplied mac address pointer
is already common->macaddr.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR5416 and all newer chipsets use a 32 bit rx timestamp, so there
is no need to keep the 15 bit timestamp extending logic around.

This patch removes ath9k_hw_extend_tsf (replaced by a call to
ath9k_hw_gettsf64), and reduces the frequency of TSF reads, which
can improve performance in some cases.

This change also has the side effect of making rx timestamps
more accurate.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9003 has been tested with the new ANI implementation
and so ANI can now be enabled for that family.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.

The old ANI implementation is left intact.

Details of the new ANI implemention:

  * ANI adjustment logic is now table driven so that each ANI level
    setting is parameterized. This makes adjustments much more
    deterministic than the old procedure based logic and allows
    adjustments to be made incrementally to several parameters per
    level.

  * ANI register settings are now relative to INI values; so ANI
    param zero level == INI value. Appropriate floor and ceiling
    values are obeyed when adjustments are combined with INI values.

  * ANI processing is done once per second rather that every 100ms.
    The poll interval is now a set upon hardware initialization and
    can be picked up by the core driver.

  * OFDM error and CCK error processing are made in a round robin
    fashion rather than allowing all OFDM adjustments to be made
    before CCK adjustments.

  * ANI adjusts MRC CCK off in the presence of high CCK errors

  * When adjusting spur immunity (SI) and OFDM weak signal detection,
    ANI now sets register values for the extension channel too

  * When adjusting FIR step (ST), ANI now sets register for FIR step
    low too

  * FIR step adjustments now allow for an extra level of immunity for
    extremely noisy environments

  * The old Noise immunity setting (NI), which changes coarse low, size
    desired, etc have been removed. Changing these settings could affect
    up RIFS RX as well.

  * CCK weak signal adjustment is no longer used

  * ANI no longer enables phy error interrupts; in all cases phy hw
    counting registers are used instead

  * The phy error count (overflow) interrupts are also no longer used
    for ANI adjustments. All ANI adjustments are made via the polling
    routine and no adjustments are possible in the ISR context anymore

  * A history settings buffer is now correctly used for each channel;
    channel settings are initialized with the defaults but later
    changes are restored when returning back to that channel

  * When scanning, ANI is disabled settings are returned to (INI) defaults.

  * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
    low/high water marks, providing increased stability/hysteresis when
    changing levels.

  * Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These will be used by the ANI code next.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes programming the byte swap registers
for chipsets other than AR9271. This is needed for
AR7010.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Async fifo is now enabled only for versions 1.3 and above.
Enable it in the appropriate place, in the reset routine,
instead of process_ini().
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a MAC address for a key table entry is flagged with the
multicast bit (0x01), indicate to the hardware that multicast
lookup instead of unicast lookup should be used. The multicast
bit itself never makes it to the actual keytable entry register,
as it is shifted out.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>