DRA72-EVM now has an upgrade to Rev C with SR2.0 silicon. As part of
this change, a few updates were factored in that were software
incompatible with previous board in few areas:
- We now use DP83867 ethernet phy instead of older DP838865 which fails
  in certain use cases.
- Two Ethernet ports now instead of the single one in rev B.
- polarities changed for certain pcf gpios
- Due to SoC phy current requirements, VDDA supplies are split between
 ldo3 and ldo2 (ldo2 was previously unused). NOTE: DSS (VDDA_VIDEO) is
 still supplied by ldo5, HDMI is now supplied by LDO2 instead of using
 LDO3.

NOTE: It does not make much sense to spin off a new board compatible
flag since there is no real benefit for the same.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

ChiliSOM has TPS65217's PWR_EN pin connected to AM335x PMIC_POWER_EN
pin. Processor's PMIC_POWER_EN is controlled by it's internal RTC, hence
RTC subsystem is responsible for proper board poweroff sequence.

This change enables complete poweroff sequence for ChiliBoard, switching
PMIC's state from ACTIVE to SLEEP.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

ChiliSOM has 2 Ethernet subsystems with different types of possibly used
PHY interfaces (i.e. MII, RMII, GMII, RGMII). Current code configured
pinmux for RMII on 1st Ethernet subsystem and enabled Ethernet MAC with
1 slave for all boards which use ChiliSOM.

This change moves pinmux configuration of 1st Ethernet subsystem to
ChiliBoard description, as this is board-specific.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

uart0 configuration code has been in SOM. However, it is possible to
use all (or none) of 6 uart's of AM335x processor present on ChiliSOM.

This fix moves declaration of uart0 from ChiliSOM to ChiliBoard, because
use of uart is strictly board-specific.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Tested-by: NBenoit Parrot <bparrot@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.

For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.

Read speed increases from 13212 KiB/ to 15753 KiB/s
and write speed was unchanged at 4404 KiB/s.

Measured using mtd_speedtest.ko on omap3-beagle-c4.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.

For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.

Read speed increases from 7869 KiB/ to 8875 KiB/s
and write speed was unchanged at 5100 KiB/s.

Measured using mtd_speedtest.ko on am335x-evm.

Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.

For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.

Read speed increases from 16516 KiB/ to 18813 KiB/s
and write speed was unchanged at 9941 KiB/s.

Measured using mtd_speedtest.ko.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.

Read speed increases from 13768 KiB/ to 17246 KiB/s.
Write speed was unchanged at 7123 KiB/s.
Measured using mtd_speedtest.ko.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides interrupts and gpio for the GPMC_WAIT pins.
Mark it as gpio and interrupt capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides interrupts and gpio for the GPMC_WAIT pins.
Mark it as gpio and interrupt capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides interrupts and gpio for the GPMC_WAIT pins.
Mark it as gpio and interrupt capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds support for turning off the main power supply via the TWL6030 on the
Kindle Fire (first generation).
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds support for the Kindle Fire (first generation) power button LEDs, that
are wired to the TWL6030 PWM outputs.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds support for USB OTG on the Kindle Fire (first generation).
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Amazon Kindle Fire (first generation) codename kc1 is a tablet that was
released by Amazon back in 2011. It is using an OMAP4430 SoC GP version.

This adds devicetree support for the device, with only a few basic features
supported, such as debug uart, i2c and internal emmc.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds the amazon vendor prefix for Amazon.com, Inc.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Before "tty: Add software emulated RS485 support for 8250" patch Baltos devices
relied on MCTRL_GPIO framework to handle both modem signals and RS485 mode.

With emulated RS485 support for 8250 we can now use these pins as dedicated
RTS/CTS signals taking advantage of hardware flow control etc. when operating
in RS232 mode.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The AM572x-IDK board is a board based on TI's AM5728 SOC
which has a dual core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The link to the data sheet and TRM can be found here:

http://www.ti.com/product/AM5728

This patch creates a common dtsi file that will provide a common board
dtsi file to define the nodes that are common to AM57xx (including the
upcoming AM5718) IDK boards.

Initial support is only for basic peripherals
Signed-off-by: NSchuyler Patton <spatton@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

TI's Industrial Communication Engine EVM is a low cost hardware mainly
developed for industrial communication type applications using serial
or Ethernet based interfaces. This platform features TI's AM3359 with
800MHz single core Cortex-A8 processor, 256MB DDR3, 64MB SPI flash,
8MB NOR Flash, mmc, usb, can, dual Ethernet ports.

For more information, look at HW user guide[1], Data manual[2].

Just add basic support for the moment.

[1] http://processors.wiki.ti.com/index.php/AM335x_Industrial_Communication_Engine_EVM_Rev2_1_HW_User_Guide
[2] http://www.ti.com/lit/ds/symlink/am3359.pdfSigned-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When possible generic node names should be used. So change the node name
from ehrpwm to pwm.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The binding definition for the PCF857x GPIO expanders doesn't mention
a "ti,pcf8575" compatible string.  This is apparently because TI is
only a second source - there is no functional difference between
PCF8575 chips manufactured by TI and NXP, and the same board might be
populated with either depending on availability.

This is not a problem in practice because the I2C core uses
of_modalias_node() before matching drivers and this strips the
manufacturer name.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NFilip Matijević <filip.matijevic.pz@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NFilip Matijević <filip.matijevic.pz@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Like the Nokia N900, the N950 has leds to show
the state of sys_clkreq and sys_off_mode pins.

A detailed description for the LEDs and
OMAP's sleep states can be found in Tony's
commit for the Nokia N900:

c1be2032Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add keypad matrix information based on data from
Nokia N950 Kernel.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add regulator configuration as found in the
board files of Nokia's kernel.
Signed-off-By: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The switch configuration for NAND is actually the other way round.
Also mention ON/OFF states as that is more natural to understand
(without the help of schematics) when compared to HIGH/LOW.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Few regulators information were missing from DT. Add those
missing regulators.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the DT node for Timer12 present on DRA7 family of
SoCs. Timer12 is present in PD_WKUPAON power domain, and
has the same capabilities as the other timers, except for
the fact that it serves as a secure timer on HS devices
and is clocked only from the secure 32K clock.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Timers 13 through 16 have been added previously in
disabled state. These timers are common timers that are
present on all DRA7 family of SoCs, so enable these
devices by default like the rest of the DMTimers.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add nodes to represent all McASP ports in the dra7 family.
For system consistency use the eDMA for audio operations. sDMA would be
fine for 4/5/6/7/8 since their DAT port is not through L3 interconnect.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>