This patch allows ports to have different link layers:
IB_LINK_LAYER_INFINIBAND or IB_LINK_LAYER_ETHERNET.  This is required
for adding IBoE (InfiniBand-over-Ethernet, aka RoCE) support.  For
devices that do not provide an implementation for querying the link
layer property of a port, we return a default value based on the
transport: RMA_TRANSPORT_IB nodes will return IB_LINK_LAYER_INFINIBAND
and RDMA_TRANSPORT_IWARP nodes will return IB_LINK_LAYER_ETHERNET.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Change abbreviated IB_QPT_RAW_ETY to IB_QPT_RAW_ETHERTYPE to make
the special QP type easier to understand.

cf http://www.mail-archive.com/linux-rdma@vger.kernel.org/msg04530.htmlSigned-off-by: NAleksey Senin <alekseys@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs.  This allows
low-level device drivers to create files in

    /sys/class/infiniband/<hca>/ports/<N>/

without having to poke through the internals of the RDMA sysfs handling.

There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

 - Add new IB_WR_MASKED_ATOMIC_CMP_AND_SWP and IB_WR_MASKED_ATOMIC_FETCH_AND_ADD
   send opcodes that can be used to post "masked atomic compare and
   swap" and "masked atomic fetch and add" work request respectively.
 - Add masked_atomic_cap capability.
 - Add mask fields to atomic struct of ib_send_wr
 - Add new opcodes to ib_wc_opcode

The new operations are described more precisely below:

* Masked Compare and Swap (MskCmpSwap)

The MskCmpSwap atomic operation is an extension to the CmpSwap
operation defined in the IB spec.  MskCmpSwap allows the user to
select a portion of the 64 bit target data for the “compare” check as
well as to restrict the swap to a (possibly different) portion.  The
pseudo code below describes the operation:

| atomic_response = *va
| if (!((compare_add ^ *va) & compare_add_mask)) then
|     *va = (*va & ~(swap_mask)) | (swap & swap_mask)
|
| return atomic_response

The additional operands are carried in the Extended Transport Header.
Atomic response generation and packet format for MskCmpSwap is as for
standard IB Atomic operations.

* Masked Fetch and Add (MFetchAdd)

The MFetchAdd Atomic operation extends the functionality of the
standard IB FetchAdd by allowing the user to split the target into
multiple fields of selectable length. The atomic add is done
independently on each one of this fields. A bit set in the
field_boundary parameter specifies the field boundaries. The pseudo
code below describes the operation:

| bit_adder(ci, b1, b2, *co)
| {
|	value = ci + b1 + b2
|	*co = !!(value & 2)
|
|	return value & 1
| }
|
| #define MASK_IS_SET(mask, attr)      (!!((mask)&(attr)))
| bit_position = 1
| carry = 0
| atomic_response = 0
|
| for i = 0 to 63
| {
|         if ( i != 0 )
|                 bit_position =  bit_position << 1
|
|         bit_add_res = bit_adder(carry, MASK_IS_SET(*va, bit_position),
|                                 MASK_IS_SET(compare_add, bit_position), &new_carry)
|         if (bit_add_res)
|                 atomic_response |= bit_position
|
|         carry = ((new_carry) && (!MASK_IS_SET(compare_add_mask, bit_position)))
| }
|
| return atomic_response
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ib_ud_header_init() first clears header and then fills up the various
fields.  Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false.  Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present.  Also remove unused calculation of
header_len.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A small change to reduce the size of ib_device to 1112 bytes
(from 1128).
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The defined SCTP number is incorrect (0x83, rather than 0x84), and
since it is not used anywhere, simply remove the definition.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Clarify the behavior of ib_post_send() when a list of work requests is
passed in and an immediate error is returned.
Signed-off-by: NBart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The RDMA CM is intended to support the use of a loopback address
when establishing a connection; however, the behavior of the CM
when loopback addresses are used is confusing and does not always
work, depending on whether loopback was specified by the server,
the client, or both.

The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address.  (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdam_bind_addr,
no device is associated with the rdma_cm_id.  Fix this.

If a loopback address is specified by the client as the destination
address for a connection, it will fail to establish a connection.
This is true even if the server is listing across all addresses or
on the loopback address itself.  The issue is that the server tries
to translate the IP address carried in the REQ message to a local
net_device address, which fails.  The translation is not needed in
this case, since the REQ carries the actual HW address that should
be used.

Finally, cleanup loopback support to be more transport neutral.
Replace separate calls to get/set the sgid and dgid from the
device address to a single call that behaves correctly depending
on the format of the device address.  And support both IPv4 and
IPv6 address formats.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>

[ Fixed RDS build by s/ib_addr_get/rdma_addr_get/  - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The struct rdma_dev_addr stores net_device address information:
the source device address, destination hardware address, and
broadcast address.  For consistency, store the net_device type
rather than converting it to the rdma_node_type.

The type indicates the format of the various hardware addresses,
which is what we're concerned with, and not the RDMA node type
that the address may map to.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Provide the device interface when resolving route information to
ensure that the correct outbound device is used.  This will also
simplify processing of sin6_scope_id for IPv6 support.

Based on work from:
David Wilder <dwilder@us.ibm.com>
Jason Gunthorpe <jgunthrope@obsidianresearch.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Export rdma_set_ib_paths to user space to allow applications to
manually set the IB path used for connections.  This allows
alternative ways for a user space application or library to obtain
path record information, including retrieving path information
from cached data, avoiding direct interaction with the IB SA.
The IB SA is a single, centralized entity that can limit scaling
on large clusters running MPI applications.

Future changes to the rdma cm can expand on this framework to
support the full range of features allowed by the IB CM, such as
separate forward and reverse paths and APM.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Reviewed-By: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix ib_set_rmpp_flags() to use the correct bit mask for RRespTime.  In
the 8-bit field of the RMPP header, the first 5 bits are RRespTime and
next 3 bits are RMPPFlags. Hence to retain the first 5 bits, the mask
should be 0xF8 instead of 0xF1.

ack_recv()-->format_ack() calls ib_set_rmpp_flags() and due to the
incorrect ANDing with 0xF1, RRespTime got changed incorrectly and RMPP
Acks sent back always had a RRespTime of 0x1E (30) which caused the
other end to consider the time outs to be approximately 4297 seconds
(i.e. in the order of 4*2^30) instead of the usual ~4 seconds (order
of 4*2^20).
Signed-off-by: NRamachandra K <ramachandra.kuchimanchi@qlogic.com>
Acked-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Base versions handle constant folding now.  For headers exposed to
userspace, we must only expose the __ prefixed versions.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The base versions handle constant folding just fine, use them
directly.  The replacements are OK in the include/ files as they are
not exported to userspace so we don't need the __ prefixed versions.

This patch does not affect code generation at all.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There are a few places where the RDMA CM code handles IPv6 by doing

	struct sockaddr		addr;
	u8			pad[sizeof(struct sockaddr_in6) -
				    sizeof(struct sockaddr)];

This is fragile and ugly; handle this in a better way with just

	struct sockaddr_storage	addr;

[ Also roll in patch from Aleksey Senin <alekseys@voltaire.com> to
  switch to struct sockaddr_storage and get rid of padding arrays in
  struct rdma_addr. ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:

This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).

I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread).  So I
CC'ed this to KVM camp.  Comments are appreciated.

A pointer to dma_mapping_ops to struct dev_archdata is added.  If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it.  If it's
NULL, the system-wide dma_ops pointer is used as before.

If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging).  It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.

The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations.  So x86 can't have dma_mapping_ops per
device.  Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.

The first patch adds the device argument to dma_mapping_error.  The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.

This patch:

dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations.  So we can't have dma_mapping_ops per device.

Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function.  x86 IOMMUs use device
argument.

[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Consumers that want to re-use their QPs in new connections need to
know when the QP has exited the timewait state.  Report the timewait
event through the rdma_cm.
Signed-off-by: NAmir Vadai <amirv@mellanox.co.il>
Acked-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add an RDMA_CM_EVENT_ADDR_CHANGE event can be used by rdma-cm
consumers that wish to have their RDMA sessions always use the same
links (eg <hca/port>) as the IP stack does.  In the current code, this
does not happen when bonding is used and fail-over happened but the IB
link used by an already existing session is operating fine.

Use the netevent notification for sensing that a change has happened
in the IP stack, then scan the rdma-cm ID list to see if there is an
ID that is "misaligned" with respect to the IP stack, and deliver
RDMA_CM_EVENT_ADDR_CHANGE for this ID.  The consumer can act on the
event or just ignore it.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Keep a pointer to the local (src) netdevice in struct rdma_dev_addr,
and copy it in as part of rdma_copy_addr().  Use rdma_translate_ip()
in cma_new_conn_id() to reduce some code duplication and also make
sure the src_dev member gets set.

In a high-availability configuration the netdevice pointer can be used
by the RDMA CM to align RDMA sessions to use the same links as the IP
stack does under fail-over and route change cases.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- Change the IB_DEVICE_ZERO_STAG flag to the transport-neutral name
  IB_DEVICE_LOCAL_DMA_LKEY, which is used by iWARP RNICs to indicate 0
  STag support and IB HCAs to indicate reserved L_Key support.

- Add a u32 local_dma_lkey member to struct ib_device.  Drivers fill
  this in with the appropriate local DMA L_Key (if they support it).

- Fix up the drivers using this flag.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch also adds a creation flag for QPs,
IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK, which when set means that
multicast sends from the QP to a group that the QP is attached to will
not be looped back to the QP's receive queue.  This can be used to
save receive resources when a consumer does not want a local copy of
multicast traffic; for example IPoIB must waste CPU time throwing away
such local copies of multicast traffic.

This patch also adds a device capability flag that shows whether a
device supports this feature or not.
Signed-off-by: NRon Livne <ronli@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds a sysfs attribute group called "proto_stats" under
/sys/class/infiniband/$device/ and populates this group with protocol
statistics if they exist for a given device.  Currently, only iWARP
stats are defined, but the code is designed to allow InfiniBand
protocol stats if they become available.  These stats are per-device
and more importantly -not- per port.

Details:

- Add union rdma_protocol_stats in ib_verbs.h.  This union allows
  defining transport-specific stats.  Currently only iwarp stats are
  defined.

- Add struct iw_protocol_stats to define the current set of iwarp
  protocol stats.

- Add new ib_device method called get_proto_stats() to return protocol
  statistics.

- Add logic in core/sysfs.c to create iwarp protocol stats attributes
  if the device is an RNIC and has a get_proto_stats() method.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds support for the IB "base memory management extension"
(BMME) and the equivalent iWARP operations (which the iWARP verbs
mandates all devices must implement).  The new operations are:

 - Allocate an ib_mr for use in fast register work requests.

 - Allocate/free a physical buffer lists for use in fast register work
   requests.  This allows device drivers to allocate this memory as
   needed for use in posting send requests (eg via dma_alloc_coherent).

 - New send queue work requests:
   * send with remote invalidate
   * fast register memory region
   * local invalidate memory region
   * RDMA read with invalidate local memory region (iWARP only)

Consumer interface details:

 - A new device capability flag IB_DEVICE_MEM_MGT_EXTENSIONS is added
   to indicate device support for these features.

 - New send work request opcodes IB_WR_FAST_REG_MR, IB_WR_LOCAL_INV,
   IB_WR_RDMA_READ_WITH_INV are added.

 - A new consumer API function, ib_alloc_mr() is added to allocate
   fast register memory regions.

 - New consumer API functions, ib_alloc_fast_reg_page_list() and
   ib_free_fast_reg_page_list() are added to allocate and free
   device-specific memory for fast registration page lists.

 - A new consumer API function, ib_update_fast_reg_key(), is added to
   allow the key portion of the R_Key and L_Key of a fast registration
   MR to be updated.  Consumers call this if desired before posting
   a IB_WR_FAST_REG_MR work request.

Consumers can use this as follows:

 - MR is allocated with ib_alloc_mr().

 - Page list memory is allocated with ib_alloc_fast_reg_page_list().

 - MR R_Key/L_Key "key" field is updated with ib_update_fast_reg_key().

 - MR made VALID and bound to a specific page list via
   ib_post_send(IB_WR_FAST_REG_MR)

 - MR made INVALID via ib_post_send(IB_WR_LOCAL_INV),
   ib_post_send(IB_WR_RDMA_READ_WITH_INV) or an incoming send with
   invalidate operation.

 - MR is deallocated with ib_dereg_mr()

 - page lists dealloced via ib_free_fast_reg_page_list().

Applications can allocate a fast register MR once, and then can
repeatedly bind the MR to different physical block lists (PBLs) via
posting work requests to a send queue (SQ).  For each outstanding
MR-to-PBL binding in the SQ pipe, a fast_reg_page_list needs to be
allocated (the fast_reg_page_list is owned by the low-level driver
from the consumer posting a work request until the request completes).
Thus pipelining can be achieved while still allowing device-specific
page_list processing.

The 32-bit fast register memory key/STag is composed of a 24-bit index
and an 8-bit key.  The application can change the key each time it
fast registers thus allowing more control over the peer's use of the
key/STag (ie it can effectively be changed each time the rkey is
rebound to a page list).
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove subversion $Id lines and improve readability by fixing other
coding style problems pointed out by checkpatch.pl.
Signed-off-by: NDotan Barak <dotanba@gmail.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The license text for several files references a third software license
that was inadvertently copied in.  Update the license to what was
intended.  This update was based on a request from HP.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In 2.6.26, we added some support for send with invalidate work
requests, including a device capability flag to indicate whether a
device supports such requests.  However, the support was incomplete:
the completion structure was not extended with a field for the key
contained in incoming send with invalidate requests.

Full support for memory management extensions (send with invalidate,
local invalidate, fast register through a send queue, etc) is planned
for 2.6.27.  Since send with invalidate is not very useful by itself,
just remove the IB_DEVICE_SEND_W_INV bit before the 2.6.26 final
release; we will add an IB_DEVICE_MEM_MGT_EXTENSIONS bit in 2.6.27,
which makes things simpler for applications, since they will not have
quite as confusing an array of fine-grained bits to check.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a new parameter, dmasync, to the ib_umem_get() prototype.  Use dmasync = 1
when mapping user-allocated CQs with ib_umem_get().
Signed-off-by: NArthur Kepner <akepner@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This converts the main ib_device to use struct device instead of struct
class_device as class_device is going away.
Signed-off-by: NTony Jones <tonyj@suse.de>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for modifying CQ parameters for controlling event
generation moderation.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a new IB_WR_SEND_WITH_INV send opcode that can be used to mark a
"send with invalidate" work request as defined in the iWARP verbs and
the InfiniBand base memory management extensions.  Also put "imm_data"
and a new "invalidate_rkey" member in a new "ex" union in struct
ib_send_wr. The invalidate_rkey member can be used to pass in an
R_Key/STag to be invalidated.  Add this new union to struct
ib_uverbs_send_wr.  Add code to copy the invalidate_rkey field in
ib_uverbs_post_send().

Fix up low-level drivers to deal with the change to struct ib_send_wr,
and just remove the imm_data initialization from net/sunrpc/xprtrdma/,
since that code never does any send with immediate operations.

Also, move the existing IB_DEVICE_SEND_W_INV flag to a new bit, since
the iWARP drivers currently in the tree set the bit.  The amso1100
driver at least will silently fail to honor the IB_SEND_INVALIDATE bit
if passed in as part of userspace send requests (since it does not
implement kernel bypass work request queueing).  Remove the flag from
all existing drivers that set it until we know which ones are OK.

The values chosen for the new flag is not consecutive to avoid clashing
with flags defined in the XRC patches, which are not merged yet but
which are already in use and are likely to be merged soon.

This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

LSO (large send offload) allows the networking stack to pass SKBs with
data size larger than the MTU to the IPoIB driver and have the HCA HW
fragment the data to multiple MSS-sized packets.  Add a device
capability flag IB_DEVICE_UD_TSO for devices that can perform TCP
segmentation offload, a new send work request opcode IB_WR_LSO,
header, hlen and mss fields for the work request structure, and a new
IB_WC_LSO completion type.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a create_flags member to struct ib_qp_init_attr that will allow a
kernel verbs consumer to create a pass special flags when creating a QP.
Add a flag value for telling low-level drivers that a QP will be used
for IPoIB UD LSO.  The create_flags member will also be useful for XRC
and ehca low-latency QP support.

Since no create_flags handling is implemented yet, add code to all
low-level drivers to return -EINVAL if create_flags is non-zero.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

IDR IDs are signed, so struct ib_uobject.id should be signed.  This
avoids some sparse pointer signedness warnings.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Avoid confusion about what it might mean, since it's never initialized.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a device capability to show when it can handle checksum offload.
Also add a send flag for inserting checksums and a csum_ok field to
the completion record.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is based on user feedback from Doug Ledford at RedHat:

Events that occur on an rdma_cm_id are reported to userspace through an
event channel.  Connection request events are reported on the event
channel associated with the listen.  When the connection is accepted, a
new rdma_cm_id is created and automatically uses the listen event
channel.  This is suboptimal where the user only wants listen events on
that channel.

Additionally, it may be desirable to have events related to connection
establishment use a different event channel than those related to
already established connections.

Allow the user to migrate an rdma_cm_id between event channels. All
pending events associated with the rdma_cm_id are moved to the new event
channel.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

To allow ULPs to tune timeout values and capture retry statistics,
report the number of times that a mad send operation was retried.

For RMPP mads, report the total number of times that the any portion
(send window) of the send operation was retried.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.

Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <mshefty@ichips.intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>