Add "const" to "static struct regmap_irq" and "static struct
regmap_config".
Acked-by: NSangbeom Kim <sbkim73@samsung.com>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Match max14577 regulator driver by of_compatible specified in mfd_cell.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds max14577 core/irq driver to support MUIC(Micro USB IC)
device and charger device and support irq domain method to control
internal interrupt of max14577 device. Also, this patch supports DT
binding with max14577_i2c_parse_dt().

The MAXIM 14577 chip contains Micro-USB Interface Circuit and Li+ Battery
Charger. It contains accessory and USB charger detection logic. It supports
USB 2.0 Hi-Speed, UART and stereo audio signals over Micro-USB connector.

The battery charger is compliant with the USB Battery Charging Specification
Revision 1.1. It has also SFOUT LDO output for powering USB devices.
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add PM suspend/resume ops to the sec MFD core driver and make it a wake
up source. This allows proper waking from suspend to RAM and also fixes
broken interrupts after resuming:
[   42.705703] sec_pmic 7-0066: Failed to read IRQ status: -5

Interrupts stop working after first resume initiated by them (e.g. by
RTC Alarm interrupt) because interrupt registers were not cleared properly.

When device is woken up from suspend by RTC Alarm, an interrupt occurs
before resuming I2C bus controller. The interrupt is handled by
regmap_irq_thread which tries to read RTC registers. This read fails
(I2C is still suspended) and RTC Alarm interrupt is disabled.

Disable the S5M8767 interrupts during suspend (disable_irq()) and enable
them during resume so the device will be still woken up but the interrupt
won't happen before resuming I2C bus.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Rename cros_ec_{probe,remove}_i2c() to cros_ec_i2c_{probe,remove}() for
consistency.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Rename cros_ec_{probe,remove}_spi() to cros_ec_spi_{probe,remove}() for
consistency.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add watchdog device support for as3722
Signed-off-by: NBibek Basu <bbasu@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As of commit 03e361b2 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The dev_cont() symbol doesn't exist, so replace it with pr_cont(). While
at it, also append a newline to the debug output to make it look nicer.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

50 us is not a long enough delay between EC transactions. At least 70 us
are needed for the 16 MHz STM32L part. Increase the delay to 200 us for
an extra safety margin.
Reviewed-by: NRandall Spangler <rspangler@chromium.org>
Signed-off-by: NDerek Basehore <dbasehore@chromium.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.

Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: NVictor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: NTaras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.

Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: NVictor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: NTaras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

We dereference "desc" before check if it is NULL. I've shifted it
around so we check first before dereferencing.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Pull battery fixes from Anton Vorontsov:
 "Two fixes:

   - fix build error caused by max17042_battery conversion to the regmap
     API.

   - fix kernel oops when booting with wakeup_source_activate enabled"

* tag 'for-v3.13-fixes' of git://git.infradead.org/battery-2.6:
  max17042_battery: Fix build errors caused by missing REGMAP_I2C config
  power_supply: Fix Oops from NULL pointer dereference from wakeup_source_activate

Pull ACPI and PM fixes and new device IDs from Rafael Wysocki:
 "These commits, except for one, are regression fixes and the remaining
  one fixes a divide error leading to a kernel panic.  The majority of
  the regressions fixed here were introduced during the 3.12 cycle, one
  of them is from this cycle and one is older.

  Specifics:

   - VGA switcheroo was broken for some users as a result of the
     ACPI-based PCI hotplug (ACPIPHP) changes in 3.12, because some
     previously ignored hotplug events started to be handled.  The fix
     causes them to be ignored again.

   - There are two more issues related to cpufreq's suspend/resume
     handling changes from the 3.12 cycle addressed by Viresh Kumar's
     fixes.

   - intel_pstate triggers a divide error in a timer function if the
     P-state information it needs is missing during initialization.
     This leads to kernel panics on nested KVM clients and is fixed by
     failing the initialization cleanly in those cases.

   - PCI initalization code changes during the 3.9 cycle uncovered BIOS
     issues related to ACPI wakeup notifications (some BIOSes send them
     for devices that aren't supposed to support ACPI wakeup).  Work
     around them by installing an ACPI wakeup notify handler for all PCI
     devices with ACPI support.

   - The Calxeda cpuilde driver's probe function is tagged as __init,
     which is incorrect and causes a section mismatch to occur during
     build.  Fix from Andre Przywara removes the __init tag from there.

   - During the 3.12 cycle ACPIPHP started to print warnings about
     missing _ADR for devices that legitimately don't have it.  Fix from
     Toshi Kani makes it only print the warnings where they make sense"

* tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
  intel_pstate: Fail initialization if P-state information is missing
  ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
  PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
  cpufreq: preserve user_policy across suspend/resume
  cpufreq: Clean up after a failing light-weight initialization
  ACPI / PCI / hotplug: Avoid warning when _ADR not present

Pull kvm bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Unconditionally uninit the MMU on nested vmexit
  KVM: x86: Fix APIC map calculation after re-enabling

Merge patches from Andrew Morton:
 "Ten fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  epoll: do not take the nested ep->mtx on EPOLL_CTL_DEL
  sh: add EXPORT_SYMBOL(min_low_pfn) and EXPORT_SYMBOL(max_low_pfn) to sh_ksyms_32.c
  drivers/dma/ioat/dma.c: check DMA mapping error in ioat_dma_self_test()
  mm/memory-failure.c: transfer page count from head page to tail page after split thp
  MAINTAINERS: set up proper record for Xilinx Zynq
  mm: remove bogus warning in copy_huge_pmd()
  memcg: fix memcg_size() calculation
  mm: fix use-after-free in sys_remap_file_pages
  mm: munlock: fix deadlock in __munlock_pagevec()
  mm: munlock: fix a bug where THP tail page is encountered

The EPOLL_CTL_DEL path of epoll contains a classic, ab-ba deadlock.
That is, epoll_ctl(a, EPOLL_CTL_DEL, b, x), will deadlock with
epoll_ctl(b, EPOLL_CTL_DEL, a, x).  The deadlock was introduced with
commmit 67347fe4 ("epoll: do not take global 'epmutex' for simple
topologies").

The acquistion of the ep->mtx for the destination 'ep' was added such
that a concurrent EPOLL_CTL_ADD operation would see the correct state of
the ep (Specifically, the check for '!list_empty(&f.file->f_ep_links')

However, by simply not acquiring the lock, we do not serialize behind
the ep->mtx from the add path, and thus may perform a full path check
when if we had waited a little longer it may not have been necessary.
However, this is a transient state, and performing the full loop
checking in this case is not harmful.

The important point is that we wouldn't miss doing the full loop
checking when required, since EPOLL_CTL_ADD always locks any 'ep's that
its operating upon.  The reason we don't need to do lock ordering in the
add path, is that we are already are holding the global 'epmutex'
whenever we do the double lock.  Further, the original posting of this
patch, which was tested for the intended performance gains, did not
perform this additional locking.
Signed-off-by: NJason Baron <jbaron@akamai.com>
Cc: Nathan Zimmer <nzimmer@sgi.com>
Cc: Eric Wong <normalperson@yhbt.net>
Cc: Nelson Elhage <nelhage@nelhage.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Min_low_pfn and max_low_pfn were used in pfn_valid macro if defined
CONFIG_FLATMEM.  When the functions that use the pfn_valid is used in
driver module, max_low_pfn and min_low_pfn is to undefined, and fail to
build.

  ERROR: "min_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
  ERROR: "max_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
  make[2]: *** [__modpost] Error 1
  make[1]: *** [modules] Error 2

This patch fix this problem.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Check DMA mapping return values in function ioat_dma_self_test() to get
rid of following warning message.

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 1203 at lib/dma-debug.c:937 check_unmap+0x4c0/0x9a0()
  ioatdma 0000:00:04.0: DMA-API: device driver failed to check map error[device address=0x000000085191b000] [size=2000 bytes] [mapped as single]
  Modules linked in: ioatdma(+) mac_hid wmi acpi_pad lp parport hidd_generic usbhid hid ixgbe isci dca libsas ahci ptp libahci scsi_transport_sas meegaraid_sas pps_core mdio
  CPU: 0 PID: 1203 Comm: systemd-udevd Not tainted 3.13.0-rc4+ #8
  Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRIVTIIN1.86B.0044.L09.1311181644 11/18/2013
  Call Trace:
    dump_stack+0x4d/0x66
    warn_slowpath_common+0x7d/0xa0
    warn_slowpath_fmt+0x4c/0x50
    check_unmap+0x4c0/0x9a0
    debug_dma_unmap_page+0x81/0x90
    ioat_dma_self_test+0x3d2/0x680 [ioatdma]
    ioat3_dma_self_test+0x12/0x30 [ioatdma]
    ioat_probe+0xf4/0x110 [ioatdma]
    ioat3_dma_probe+0x268/0x410 [ioatdma]
    ioat_pci_probe+0x122/0x1b0 [ioatdma]
    local_pci_probe+0x45/0xa0
    pci_device_probe+0xd9/0x130
    driver_probe_device+0x171/0x490
    __driver_attach+0x93/0xa0
    bus_for_each_dev+0x6b/0xb0
    driver_attach+0x1e/0x20
    bus_add_driver+0x1f8/0x2b0
    driver_register+0x81/0x110
    __pci_register_driver+0x60/0x70
    ioat_init_module+0x89/0x1000 [ioatdma]
    do_one_initcall+0xe2/0x250
    load_module+0x2313/0x2a00
    SyS_init_module+0xd9/0x130
    system_call_fastpath+0x1a/0x1f
  ---[ end trace 990c591681d27c31 ]---
  Mapped at:
    debug_dma_map_page+0xbe/0x180
    ioat_dma_self_test+0x1ab/0x680 [ioatdma]
    ioat3_dma_self_test+0x12/0x30 [ioatdma]
    ioat_probe+0xf4/0x110 [ioatdma]
    ioat3_dma_probe+0x268/0x410 [ioatdma]
Signed-off-by: NJiang Liu <jiang.liu@linux.intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Memory failures on thp tail pages cause kernel panic like below:

   mce: [Hardware Error]: Machine check events logged
   MCE exception done on CPU 7
   BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
   IP: [<ffffffff811b7cd1>] dequeue_hwpoisoned_huge_page+0x131/0x1e0
   PGD bae42067 PUD ba47d067 PMD 0
   Oops: 0000 [#1] SMP
  ...
   CPU: 7 PID: 128 Comm: kworker/7:2 Tainted: G   M       O 3.13.0-rc4-131217-1558-00003-g83b7df08e462 #25
  ...
   Call Trace:
     me_huge_page+0x3e/0x50
     memory_failure+0x4bb/0xc20
     mce_process_work+0x3e/0x70
     process_one_work+0x171/0x420
     worker_thread+0x11b/0x3a0
     ? manage_workers.isra.25+0x2b0/0x2b0
     kthread+0xe4/0x100
     ? kthread_create_on_node+0x190/0x190
     ret_from_fork+0x7c/0xb0
     ? kthread_create_on_node+0x190/0x190
  ...
   RIP   dequeue_hwpoisoned_huge_page+0x131/0x1e0
   CR2: 0000000000000058

The reasoning of this problem is shown below:
 - when we have a memory error on a thp tail page, the memory error
   handler grabs a refcount of the head page to keep the thp under us.
 - Before unmapping the error page from processes, we split the thp,
   where page refcounts of both of head/tail pages don't change.
 - Then we call try_to_unmap() over the error page (which was a tail
   page before). We didn't pin the error page to handle the memory error,
   this error page is freed and removed from LRU list.
 - We never have the error page on LRU list, so the first page state
   check returns "unknown page," then we move to the second check
   with the saved page flag.
 - The saved page flag have PG_tail set, so the second page state check
   returns "hugepage."
 - We call me_huge_page() for freed error page, then we hit the above panic.

The root cause is that we didn't move refcount from the head page to the
tail page after split thp.  So this patch suggests to do this.

This panic was introduced by commit 524fca1e ("HWPOISON: fix
misjudgement of page_action() for errors on mlocked pages").  Note that we
did have the same refcount problem before this commit, but it was just
ignored because we had only first page state check which returned "unknown
page." The commit changed the refcount problem from "doesn't work" to
"kernel panic."
Signed-off-by: NNaoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: NWanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>	[3.9+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Setup correct zynq entry.
 - Add missing cadence_ttc_timer maintainership
 - Add zynq wildcard
 - Add xilinx wildcard
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sasha Levin reported the following warning being triggered

  WARNING: CPU: 28 PID: 35287 at mm/huge_memory.c:887 copy_huge_pmd+0x145/ 0x3a0()
  Call Trace:
    copy_huge_pmd+0x145/0x3a0
    copy_page_range+0x3f2/0x560
    dup_mmap+0x2c9/0x3d0
    dup_mm+0xad/0x150
    copy_process+0xa68/0x12e0
    do_fork+0x96/0x270
    SyS_clone+0x16/0x20
    stub_clone+0x69/0x90

This warning was introduced by "mm: numa: Avoid unnecessary disruption
of NUMA hinting during migration" for paranoia reasons but the warning
is bogus.  I was thinking of parallel races between NUMA hinting faults
and forks but this warning would also be triggered by a parallel reclaim
splitting a THP during a fork.  Remote the bogus warning.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The mem_cgroup structure contains nr_node_ids pointers to
mem_cgroup_per_node objects, not the objects themselves.
Signed-off-by: NVladimir Davydov <vdavydov@parallels.com>
Acked-by: NMichal Hocko <mhocko@suse.cz>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

remap_file_pages calls mmap_region, which may merge the VMA with other
existing VMAs, and free "vma".  This can lead to a use-after-free bug.
Avoid the bug by remembering vm_flags before calling mmap_region, and
not trying to dereference vma later.
Signed-off-by: NRik van Riel <riel@redhat.com>
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 7225522b ("mm: munlock: batch non-THP page isolation and
munlock+putback using pagevec" introduced __munlock_pagevec() to speed
up munlock by holding lru_lock over multiple isolated pages.  Pages that
fail to be isolated are put_page()d immediately, also within the lock.

This can lead to deadlock when __munlock_pagevec() becomes the holder of
the last page pin and put_page() leads to __page_cache_release() which
also locks lru_lock.  The deadlock has been observed by Sasha Levin
using trinity.

This patch avoids the deadlock by deferring put_page() operations until
lru_lock is released.  Another pagevec (which is also used by later
phases of the function is reused to gather the pages for put_page()
operation.
Signed-off-by: NVlastimil Babka <vbabka@suse.cz>
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since commit ff6a6da6 ("mm: accelerate munlock() treatment of THP
pages") munlock skips tail pages of a munlocked THP page.  However, when
the head page already has PageMlocked unset, it will not skip the tail
pages.

Commit 7225522b ("mm: munlock: batch non-THP page isolation and
munlock+putback using pagevec") has added a PageTransHuge() check which
contains VM_BUG_ON(PageTail(page)).  Sasha Levin found this triggered
using trinity, on the first tail page of a THP page without PageMlocked
flag.

This patch fixes the issue by skipping tail pages also in the case when
PageMlocked flag is unset.  There is still a possibility of race with
THP page split between clearing PageMlocked and determining how many
pages to skip.  The race might result in former tail pages not being
skipped, which is however no longer a bug, as during the skip the
PageTail flags are cleared.

However this race also affects correctness of NR_MLOCK accounting, which
is to be fixed in a separate patch.
Signed-off-by: NVlastimil Babka <vbabka@suse.cz>
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull GFS2 fixes from Steven Whitehouse:
 "Here is a set of small fixes for GFS2.  There is a fix to drop
  s_umount which is copied in from the core vfs, two patches relate to a
  hard to hit "use after free" and memory leak.  Two patches related to
  using DIO and buffered I/O on the same file to ensure correct
  operation in relation to glock state changes.  The final patch adds an
  RCU read lock to ensure correct locking on an error path"

* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: Fix unsafe dereference in dump_holder()
  GFS2: Wait for async DIO in glock state changes
  GFS2: Fix incorrect invalidation for DIO/buffered I/O
  GFS2: Fix slab memory leak in gfs2_bufdata
  GFS2: Fix use-after-free race when calling gfs2_remove_from_ail
  GFS2: don't hold s_umount over blkdev_put