Commit 7f854420
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.

Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John Crispin says:

====================
net: mediatek: various small fixes

This series contains various small fixes that we stumbled across while
doing thorough testing and code level reviewing of the driver.

Changes in V2:
* drop the DQL patch from the list until a better solution is found
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code checks if the queue should be stopped because we are below the
threshold of free descriptors only to check if it should be started again.
If we do end up in a state where we are at the threshold limit, it makes
more sense to just stop the queue and wait for the next IRQ to trigger the
TX housekeeping again. There is no rush in enqueuing the next packet, it
needs to wait for all the others in the queue to be dispatched first
anyway.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code unconditionally wakes up the queue at the end of each
tx_poll action. Change the code to only wake up the queues if any of
them have actually been stopped before.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TX ring setup has an off by one error causing it to not utilise all
descriptors. This has the side effect that we need to reset the next
pointer at runtime to make it work. Fix the off by one and remove the
code fixing the ring at runtime.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During stress testing, after reducing the threshold value, we have seen
TX timeouts that were caused by the watchdog_timeo value being too low.
Increase the value to 5 * HZ which is a value commonly used by many other
drivers.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The logic to calculate the threshold value for stopping the TX queue is
bad. Currently it will always use 1/2 of the rings size, which is way too
much. Set the threshold to MAX_SKB_FRAGS. This makes sure that the queue
is stopped when there is not enough room to accept an additional segment. 
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code only disables those IRQs that we will later use. To
ensure that we have a predefined state, we really want to disable all IRQs.
Change the code to disable all IRQs to achieve this.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QDMA engine can fail to update the register pointing to the next TX
descriptor if this bit does not get set in the QDMA configuration register.
Not setting this bit can result in invalid values inside the TX rings
registers which will causes TX stalls.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two places inside mtk_poll_rx where rx_dropped is not being
incremented properly. Fix this by adding the missing code to increment
the counter.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The lookup of the tx_buffer in the error path inside mtk_tx_map() uses the
wrong descriptor pointer. This looks like a copy & paste error. Change the
code to use the correct pointer.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Scratch memory gets allocated in mtk_init_fq_dma() but the corresponding
code to free it is missing inside mtk_dma_free() causing a memory leak.
With this patch applied, we can run ifconfig up/down several thousand
times without any problems.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code fails to check if the scratch memory was properly allocated. Add
this check and return with an error if the allocation failed.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The symbol ic_addrservaddr is not static, but has no declaration
to match so make it static to fix the following warning:

net/ipv4/ipconfig.c:130:8: warning: symbol 'ic_addrservaddr' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions inet_diag_msg_common_fill and inet_diag_msg_attrs_fill
seem to have been missed from the include/linux/inet_diag.h header
file. Add them to fix the following warnings:

net/ipv4/inet_diag.c:69:6: warning: symbol 'inet_diag_msg_common_fill' was not declared. Should it be static?
net/ipv4/inet_diag.c:108:5: warning: symbol 'inet_diag_msg_attrs_fill' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8626c56c ("bridge: fix potential use-after-free when hook
returns QUEUE or STOLEN verdict") fixed incorrect usage of NF_HOOK's
return value by consuming packets in okfn via br_pass_frame_up().

However, this function re-injects packets to the Rx path with skb->dev
set to the bridge device, which breaks kernel's STP, as all STP packets
appear to originate from the bridge device itself.

Instead, if STP is enabled and bridge isn't a 802.1ad bridge, then learn
packet's SMAC and inject it back to the Rx path for further processing
by the packet handlers.

The patch also makes netfilter's behavior consistent with regards to
packets destined to the Bridge Group Address, as no hook registered at
LOCAL_IN will ever be called, regardless if STP is enabled or not.

Cc: Florian Westphal <fw@strlen.de>
Cc: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Fixes: 8626c56c ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We detected some problems using the smsc lan8720a in combination with
i.MX28 and tracked this down to commit 21009686 ("net: phy: smsc: move
smsc_phy_config_init reset part in a soft_reset function")
With 21009686 the generic soft reset is replaced by a specific function
which handles power down state correctly. But additionally the soft reset
itself got conditional and is therefore also only performed if the phy is
in power down state.

This patch keeps the conditional wake up from power down, but
re-introduces the unconditional soft reset using the generic soft reset
function.
It was tested on linux-4.1.25 and linux-4.7.0-rc2.
Signed-off-by: NManfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) nfnetlink timestamp taken from wrong skb, fix from Florian Westphal.

 2) Revert some msleep conversions in rtlwifi as these spots are in
    atomic context, from Larry Finger.

 3) Validate that NFTA_SET_TABLE attribute is actually specified when we
    call nf_tables_getset().  From Phil Turnbull.

 4) Don't do mdio_reset in stmmac driver with spinlock held as that can
    sleep, from Vincent Palatin.

 5) sk_filter() does things other than run a BPF filter, so we should
    not elide it's call just because sk->sk_filter is NULL.  Fix from
    Eric Dumazet.

 6) Fix missing backlog updates in several packet schedulers, from Cong
    Wang.

 7) bnx2x driver should allow VLAN add/remove while the interface is
    down, from Michal Schmidt.

 8) Several RDS/TCP race fixes from Sowmini Varadhan.

 9) fq_codel scheduler doesn't return correct queue length in dumps,
    from Eric Dumazet.

10) Fix TCP stats for tail loss probe and early retransmit in ipv6, from
    Yuchung Cheng.

11) Properly initialize udp_tunnel_socket_cfg in l2tp_tunnel_create(),
    from Guillaume Nault.

12) qfq scheduler leaks SKBs if a kzalloc fails, fix from Florian
    Westphal.

13) sock_fprog passed into PACKET_FANOUT_DATA needs compat handling,
    from Willem de Bruijn.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
  vmxnet3: segCnt can be 1 for LRO packets
  packet: compat support for sock_fprog
  stmmac: fix parameter to dwmac4_set_umac_addr()
  net/mlx5e: Fix blue flame quota logic
  net/mlx5e: Use ndo_stop explicitly at shutdown flow
  net/mlx5: E-Switch, always set mc_promisc for allmulti vports
  net/mlx5: E-Switch, Modify node guid on vf set MAC
  net/mlx5: E-Switch, Fix vport enable flow
  net/mlx5: E-Switch, Use the correct error check on returned pointers
  net/mlx5: E-Switch, Use the correct free() function
  net/mlx5: Fix E-Switch flow steering capabilities check
  net/mlx5: Fix flow steering NIC capabilities check
  net/mlx5: Fix root flow table update
  net/mlx5: Fix MLX5_CMD_OP_MAX to be defined correctly
  net/mlx5: Fix masking of reserved bits in XRCD number
  net/mlx5: Fix the size of modify QP mailbox
  mlxsw: spectrum: Don't sleep during ndo_get_phys_port_name()
  mlxsw: spectrum: Make split flow match firmware requirements
  wext: Fix 32 bit iwpriv compatibility issue with 64 bit Kernel
  cfg80211: remove get/set antenna and tx power warnings
  ...

Pull sound fixes from Takashi Iwai:
 "We have only few, mainly HD-audio device-specific fixes.  Realtek
  codec driver got a slightly more LOC, but they are all for the new
  codec chip, and won't affect others at all"

* tag 'sound-4.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Add PCI ID for Kabylake
  ALSA: hda/realtek: Add T560 docking unit fixup
  ALSA: hda - Fix headset mic detection problem for Dell machine
  ALSA: uapi: Add three missing header files to Kbuild file
  ALSA: hda/realtek - Add support for new codecs ALC700/ALC701/ALC703
  ALSA: hda/realtek - ALC256 speaker noise issue

Pull drm fixes from Dave Airlie:
 "This weeks instalment of fixes:

  amdgpu:
     Lots of memory leak and firmware leak fixes

  nouveau:
     Collection of display fixes, KASAN fixes

  vc4:
     vblank/pageflipping fixes

  fsl-dcu:
     Regmap cache fix

  omap:
     Unused variable warning fix.

  Nothing too surprising so far"

* tag 'drm-fixes-for-v4.7-rc3' of git://people.freedesktop.org/~airlied/linux: (46 commits)
  drm/amdgpu: fix warning with powerplay disabled.
  drm/amd/powerplay: delete useless code as pptable changed in vbios.
  drm/amd/powerplay: fix bug visit array out of bounds
  drm/amdgpu: fix smu ucode memleak (v2)
  drm/amdgpu: add release firmware for cgs
  drm/amdgpu: fix tonga smu_fini mem leak
  drm/amdgpu: fix fiji smu fini mem leak
  drm/amdgpu: fix cik sdma ucode memleak
  drm/amdgpu: fix sdma24 ucode mem leak
  drm/amdgpu: fix sdma3 ucode mem leak
  drm/amdgpu: fix uvd fini mem leak
  drm/amdgpu: fix gfx 7 ucode mem leak
  drm/amdgpu: fix gfx8 ucode mem leak
  drm/amdgpu: fix missing free wb for cond_exec
  drm/amdgpu: fix memleak in pptable_init
  drm/amdgpu: fix mem leak in atombios
  drm/amdgpu: fix mem leak in pplib/hwmgr
  drm/amdgpu: fix mem leak in smumgr
  drm/amdgpu: add pipeline sync while vmid switch in same ctx
  drm/amdgpu: vBIOS post only call when mem_size zero
  ...

Pull ACPI fix from Rafael Wysocki:
 "A recently introduced boot regression related to the ACPI EC
  initialization is addressed by restoring the previous behavior (Lv
  Zheng)"

* tag 'acpi-4.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / EC: Fix a boot EC regresion by restoring boot EC support for the DSDT EC

Pull power management fixes from Rafael Wysocki:
 "Stable-candidate fixes for the intel_pstate driver and the cpuidle
  core.

  Specifics:

   - Fix two intel_pstate initialization issues, one of which was
     introduced during the 4.4 cycle (Srinivas Pandruvada)

   - Fix kernel build with CONFIG_UBSAN set and CONFIG_CPU_IDLE unset
     (Catalin Marinas)"

* tag 'pm-4.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: intel_pstate: Fix ->set_policy() interface for no_turbo
  cpufreq: intel_pstate: Fix code ordering in intel_pstate_set_policy()
  cpuidle: Do not access cpuidle_devices when !CONFIG_CPU_IDLE

Merge misc fixes from Andrew Morton:
 "7 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/fadvise.c: do not discard partial pages with POSIX_FADV_DONTNEED
  mm: introduce dedicated WQ_MEM_RECLAIM workqueue to do lru_add_drain_all
  kernel/relay.c: fix potential memory leak
  mm: thp: broken page count after commit aa88b68c
  revert "mm: memcontrol: fix possible css ref leak on oom"
  kasan: change memory hot-add error messages to info messages
  mm/hugetlb: fix huge page reserve accounting for private mappings

The device emulation may send segCnt of 1 for LRO packets.
Signed-off-by: NShrikrishna Khare <skhare@vmware.com>
Signed-off-by: NJin Heo <heoj@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Socket option PACKET_FANOUT_DATA takes a struct sock_fprog as argument
if PACKET_FANOUT has mode PACKET_FANOUT_CBPF. This structure contains
a pointer into user memory. If userland is 32-bit and kernel is 64-bit
the two disagree about the layout of struct sock_fprog.

Add compat setsockopt support to convert a 32-bit compat_sock_fprog to
a 64-bit sock_fprog. This is analogous to compat_sock_fprog support for
SO_REUSEPORT added in commit 19575988 ("soreuseport: add compat
case for setsockopt SO_ATTACH_REUSEPORT_CBPF").
Reported-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac4_set_umac_addr() takes a struct mac_device_info as
the first parameter, but is being passed a ioaddr instead from
dwmac4_set_filter(). Fix the warning/bug by changing the first
parameter.

drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46:    expected struct mac_device_info *hw
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46:    got void [noderef] <asn:2>*ioaddr

Note, only compile tested this as do not have any
hardware with it in.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 fixes for 4.7-rc

The following series provides some small fixes for mlx5 driver.

Two small fixes for the mlx5e netdev, the 1st is for the blue flame
quota accounting and the 2nd is a small refactoring in shutdown flow.

Five trivial fixes for mlx5 E-Switch.
	- Allmulti mc_promisc flag was not set in a specific flow.
	- Modify VF node guid when admin mac is changed.
	- Race in vport enable flow.
	- Misc code fixes (kvfree when needed and error pointers checking).

Three in mlx5 steering area.  Correct capabilities checking and root flow table update.

Three misc fixes in mlx5 commands enum and layouts.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Blue flame is a latency enhancement feature that allows the driver to
write the packet data directly to the NIC's registers thus making the
read of the packet data from host memory redundant.

We maintain a quota for the blue flame which is reloaded whenever we
identify that the hardware is processing send requests and processes
them fast enough so by the time we post the next send request it was
able to process all the pending ones. This indicates that the hardware
is capable of processing more blue flame requests efficiently. The blue
flame quota is decremented whenever we send using blue flame.

The current code erroneously clears the budget if we did not use blue
flame for the current post send operation and we fix it here.

Fixes: 88a85f99 ('net/mlx5e: TX latency optimization to save DMA reads')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation copies the flow of ndo_stop instead of
calling it explicitly, Fixed it.

Fixes: 5fc7197d ("net/mlx5: Add pci shutdown callback")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the mc_promisc flag also in the case of adding new mc address to
existing allmulti vport.

Fixes: a35f71f2 ('net/mlx5: E-Switch, Implement promiscuous rx modes vf request handling')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In RoCE, the RDMA-CM needs the node guid to establish connection
between nodes.
Today, the node guid exposed to mlx5 Ethernet VFs is zero, therefore
RDMA-CM on the VF is broken.

Whenever the administrator sets a MAC for a VF, derive the node guid
from it and set it as well in the following way:
MAC: e4:1d:2d:b3:f4:01 -> node_guid: e4:1d:2d:ff:fe:b3:f4:01

Fixes: 77256579 ('net/mlx5: E-Switch, Introduce Vport...')
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reorder vport enable flow to mark the vport as enabled before calling
the vport change handler which was modified to handle the case for
when vport is not enabled.

This fixes the case for when the PF netdev is open before sriov is
enabled, once sriov is enabled at esw_enable_vport,
esw_vport_change_handle_locked didn't read the PF context since it
thought the PF vport was not enabled.

When we enable the vport, arming for events is not required anymore,
since it's done on the vport change handle

Fixes: 586cfa7f ('net/mlx5: E-Switch, Use vport event handler for vport cleanup')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlx5 flow-steering API (mlx5_create_flow_table/group/rule) never
returns null pointer on error. Even if it was doing that, checking
for IS_ERR_OR_NULL(p) and then returning PTR_ERR(p) would have cause
bugs, since PTR_ERR(NULL) --> success, crash.

To make things more robust and protect against related future bugs,
convert all IS_ERR_OR_NULL checks on returned values to IS_ERR.

Fixes: 5742df0f ('net/mlx5: E-Switch, Introduce VST vport ingress/egress ACLs')
Fixes: 86d722ad ('net/mlx5: Use flow steering infrastructure for mlx5_en')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We must use kvfree() for something that could have been allocated with vzalloc(),
do that.

Fixes: 5742df0f ('net/mlx5: E-Switch, Introduce VST vport ingress/egress ACLs')
Fixes: 86d722ad ('net/mlx5: Use flow steering infrastructure for mlx5_en')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing capabilities check for E-Switch FDB and ACLs flow
tables before creating their namespace in flow steering.

Fixes: efdc810b ('net/mlx5: Flow steering, Add vport ACL support')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow steering infrastructure is currently used only on link layer
ethernet, therefore the driver should initialize the flow steering
when the device link layer is ethernet.

In addition, add missing capability check before initializing the
namespace of NIC RX flow tables.

Fixes: 25302363 ('net/mlx5_core: Flow steering tree initialization')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we destroy the last flow table we need to update
the root_ft to NULL.

It fixes an issue for when the last flow table is destroyed
and recreated again, root_ft pointer will not be updated,
as a result traffic will be dropped.

Fixes: 2cc43b49 ('net/mlx5_core: Managing root flow table')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Having MLX5_CMD_OP_MAX on another file causes us to repeatedly miss
accounting new commands added to the driver and hence there're no entries
for them in debugfs. To solve that, we integrate it into the commands enum
as the last entry.

Fixes: 34a40e68 ('net/mlx5_core: Introduce modify flow table command')
Signed-off-by: NShahar Klein <shahark@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mask the reserved bits when reading the number of newly
created XRCD.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 16 reserved bytes at the end of mlx5_modify_qp_mbox_in to
match the hardware spec definition.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>