Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 16 4月, 2015 1 次提交
    • E
      bnx2x: Fix busy_poll vs netpoll · 074975d0
      由 Eric Dumazet 提交于 
      Commit 9a2620c8 ("bnx2x: prevent WARN during driver unload")
switched the napi/busy_lock locking mechanism from spin_lock() into
spin_lock_bh(), breaking inter-operability with netconsole, as netpoll
disables interrupts prior to calling our napi mechanism.

This switches the driver into using atomic assignments instead of the
spinlock mechanisms previously employed.

Based on initial patch from Yuval Mintz & Ariel Elior

I basically added softirq starvation avoidance, and mixture
of atomic operations, plain writes and barriers.

Note this slightly reduces the overhead for this driver when no
busy_poll sockets are in use.

Fixes: 9a2620c8 ("bnx2x: prevent WARN during driver unload")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      074975d0
  3. 15 4月, 2015 9 次提交
  5. 02 4月, 2015 3 次提交
    • P
      net: bcmgenet: enable MoCA link state change detection · 8d88c6eb
      由 Petri Gynther 提交于 
      Currently, MoCA fixed PHYs are always in link-up state, regardless of
whether the link is actually up or not.

Add code to properly detect MoCA link state changes and to reflect the
new state in MoCA fixed PHY. Only GENET V3 and V4 MACs are capable of
detecting MoCA link state changes.

The code works as follows:
1. GENET MAC detects MoCA link state change and issues UMAC_IRQ_LINK_UP
   or UMAC_IRQ_LINK_DOWN interrupt.
2. Link up/down interrupt is processed in bcmgenet_irq_task(), which
   calls phy_mac_interrupt().
3. phy_mac_interrupt() updates the fixed PHY phydev->link and kicks
   the PHY state machine.
4. PHY state machine proceeds to read the fixed PHY link status
   register.
5. When the fixed PHY link status register is being read, the new
   function bcmgenet_fixed_phy_link_update() gets called. It copies
   the fixed PHY phydev->link value to the fixed PHY status->link.
6. PHY state machine receives the new link state of the fixed PHY.
7. MoCA fixed PHY link state now correctly reflects the real MoCA
   hardware link state.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8d88c6eb
    • Y
      bnx2x: Fix kdump when iommu=on · da254fbc
      由 Yuval Mintz 提交于 
      When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.

Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.

This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      da254fbc
    • Y
      bnx2x: Fix kdump on 4-port device · 3d6b7253
      由 Yuval Mintz 提交于 
      When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.

On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.

This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3d6b7253
  7. 01 4月, 2015 14 次提交
  9. 30 3月, 2015 1 次提交
  11. 28 3月, 2015 7 次提交
  13. 24 3月, 2015 5 次提交