TPS65911 adds new interrupt sources, as well as two new registers
to handle them, one for interrupt status and one for interrupt
masking. The added irqs are:

-VMBCH2 - Low and High threshold
-GPIO1-8 - Rising and falling edge detection
-WTCHDG - Watchdog interrupt
-PWRDN	- PWRDN reset interrupt

The code should handle these new registers only when the chip
version is TPS65911.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The tps65911 chip introduces new features, including changes in
the regulator module.

- VDD1 and VDD2 remain unchanged.
- VDD3 is now named VDDCTRL and has a wider voltage range.
- LDOs are now named LDO1...8 and voltage ranges are sequential,
  making LDOs easier to handle.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The TPS65911 is the next generation of the TPS65910 family of
PMIC chips. It adds a few features:

- Watchdog Timer
- PWM & LED generators
- Comparators for system control status

It also adds a set of Interrupts and GPIOs, among other things.

The driver exports a function to identify between different
versions of the tps65910 family, allowing other modules to
identify the capabilities of the current chip.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

We use val as array index,
thus the valid value rangae for val should be 0 .. n_voltages-1.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Voltage values should be expressed in microvolts, not in milivolts.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NRanjani Vaidyanathan <ra5478@freescale.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In current implementation, the original macro implementation assumes the caller
pass the parameter starting from 1 (to match the register names in datasheet).
Thus we have unneeded plus one then minus one operations
when using MAX8997_REG_BUCK1DVS/MAX8997_REG_BUCK2DVS/MAX8997_REG_BUCK5DVS macros.

This patch removes these macros to avoid unneeded plus one then minus one operations
without reducing readability.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

If bytes == (TPS65910_MAX_REGISTER + 1), we have a buffer overflow when
doing memcpy(&msg[1], src, bytes).
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

When applying the set_voltage() requests from consumers skip over those
consumers that haven't set anything, otherwise we'll come out with a
maximum voltage of zero.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

If either a regulator driver can't tell us what the optimum mode is (or
doesn't have modes in the first place) or the system doesn't allow DRMS
changes then it's more helpful for users to just say that we're in the
optimal mode, even if it's from a selection of one.

Still report errors if the process of picking and setting a mode changes as
this may indicate that we're stuck in a low power mode and unable to deliver
a higher current that the consumer just asked for.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

fix unreachable code.
Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The desc_id variable should not be a static variable.

The rest of the code assumes the desc_id must less than TPSxxxxx_NUM_REGULATOR.
If we set desc_id to be a static variable, checking the return value of
rdev_get_id() may return error.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

On May 10, 2011, at 9:27 PM, Stephen Rothwell wrote:

> Hi Jorge,
>
> On Tue, 10 May 2011 12:30:36 -0500 Jorge Eduardo Candelaria <jedu@slimlogic.co.uk> wrote:
>>
>> On May 10, 2011, at 3:38 AM, Liam Girdwood wrote:
>>
>>> On Tue, 2011-05-10 at 12:44 +1000, Stephen Rothwell wrote:
>>>> Hi Liam,
>>>>
>>>> After merging the voltage tree, today's linux-next build (x86_64
>>>> allmodconfig) failed like this:
>>>>
>>>> ERROR: "tps65910_gpio_init" [drivers/mfd/tps65910.ko] undefined!
>>>> ERROR: "tps65910_irq_init" [drivers/mfd/tps65910.ko] undefined!
>>>> ERROR: "irq_modify_status" [drivers/mfd/tps65910-irq.ko] undefined!
>>>> ERROR: "irq_set_chip_and_handler_name" [drivers/mfd/tps65910-irq.ko] undefined!
>>>> ERROR: "handle_edge_irq" [drivers/mfd/tps65910-irq.ko] undefined!
>>>>
>>>> I have used the voltage tree from next-20110509 for today.
>>>
>>> Jorge, could you send a fix for this today.
>>
>> The following patch should solve this:
>>
>> From: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
>> MFD: Fix TPS65910 build
>>
>> Support for tps65910 as a module is not available. The driver can
>> only be compiled as built-in. OTOH, the regulator driver can still
>> be built as module without breaking the compilation.
>>
>> Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
>
> Today (even with the above patch included) I got these errors from the
> x86_64 allmodconfig build:
>
> tps65910.c:(.text+0xf4140): undefined reference to `i2c_master_send'
> drivers/built-in.o: In function `tps65910_i2c_read':
> tps65910.c:(.text+0xf41d2): undefined reference to `i2c_transfer'
> drivers/built-in.o: In function `tps65910_i2c_init':
> tps65910.c:(.init.text+0xcb83): undefined reference to `i2c_register_driver'
> drivers/built-in.o: In function `tps65910_i2c_exit':
> tps65910.c:(.exit.text+0x6e0): undefined reference to `i2c_del_driver'
>
> I have used the voltage tree from next-20110509 again today.

Following patch should fix the dependency problems. Please review:

From: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
[PATCH] MFD: TPS65910: Fix I2C dependency

TPS65910 driver can only be compiled built-in, so the I2C driver
should be as well.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

I check this patch again and found this actually is not a bug
because MC13xxx_DEFINE explictly defines the order of each entry in the array.

Thus revert the patch.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

These became unused with the IRQ removal patch, I'm fairly sure that a
patch was sent earlier by someone else but it doesn't seem to have been
applied and I don't have a copy sitting around any more.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

On May 10, 2011, at 3:38 AM, Liam Girdwood wrote:

> On Tue, 2011-05-10 at 12:44 +1000, Stephen Rothwell wrote:
>> Hi Liam,
>>
>> After merging the voltage tree, today's linux-next build (x86_64
>> allmodconfig) failed like this:
>>
>> ERROR: "tps65910_gpio_init" [drivers/mfd/tps65910.ko] undefined!
>> ERROR: "tps65910_irq_init" [drivers/mfd/tps65910.ko] undefined!
>> ERROR: "irq_modify_status" [drivers/mfd/tps65910-irq.ko] undefined!
>> ERROR: "irq_set_chip_and_handler_name" [drivers/mfd/tps65910-irq.ko] undefined!
>> ERROR: "handle_edge_irq" [drivers/mfd/tps65910-irq.ko] undefined!
>>
>> I have used the voltage tree from next-20110509 for today.
>
> Jorge, could you send a fix for this today.
>
> Thanks
>
> Liam
>

The following patch should solve this:

From: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
MFD: Fix TPS65910 build

Support for tps65910 as a module is not available. The driver can
only be compiled as built-in. OTOH, the regulator driver can still
be built as module without breaking the compilation.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The regulator module consists of 3 DCDCs and 8 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components
Signed-off-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This module controls the interrupt handling for the tps chip. The
interrupt sources are the following:

- GPIO falling/rising edge detection
- Battery voltage below/above threshold
- PWRON signal
- PWRHOLD signal
- Temperature detection
- RTC alarm and periodic event
Signed-off-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

TPS65910 has one configurable GPIO that can be used for several
purposes. Subsequent versions of the TPS chip support more than
one GPIO.
Signed-off-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The TPS65910 chip is a power management IC for multimedia and handheld
devices. It contains the following components:

- Regulators
- GPIO controller
- RTC

The tps65910 core driver is registered as a platform driver and provides
communication through I2C with the host device for the different
components.
Signed-off-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Currently, we call mc13xxx_reg_read and mc13xxx_reg_rmw for the same register.
This can be converted to simply a mc13xxx_reg_read and a mc13xxx_reg_write,
thus save a redundant register read.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Some systems, particularly physically large systems used for early
prototyping, may experience substantial voltage drops between the regulator
and the consumers as a result of long traces in the system. With these
systems voltages may need to be set higher than requested in order to
ensure reliable system operation.

Allow systems to work around such hardware issues by allowing constraints
to supply an offset to be applied to any requested and reported voltages.
This is not ideal, especially since the voltage drop may be load dependant,
but is sufficient for most affected systems, it is not expected to be used
in production hardware. The offset is applied after all constraint
processing so constraints should be specified in terms of consumer values
not physically configured values.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

supply_regulator_dev (using a struct pointer) has been deprecated in favour
of supply_regulator (using a regulator name) for quite a few releases
now with a warning generated if it is used and there are no current in tree
users so just remove the code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In include/linux/mfd/mc13892.h, we define MC13892_VCOINCELL as 23.
Thus VCOINCELL should be defined as 23th element in mc13892_regulators array, not the first one.
This actually fixes an off-by-one bug while accessing mc13892_regulators array.

For example,
In mc13892_regulator_probe, we use MC13892_VCAM as array index of mc13892_regulators array.
        mc13892_regulators[MC13892_VCAM].desc.ops->set_mode
                = mc13892_vcam_set_mode;
Currently, it access mc13892_regulators[12] ,which is VAUDIO not VCAM.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Don't go looking up the rdev pointer every time, just use a local variable
like everything else.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The second parameter of regulator_mode_constrain takes a pointer.

This patch fixes below warning:
drivers/regulator/core.c: In function 'regulator_set_mode':
drivers/regulator/core.c:2014: warning: passing argument 2 of 'regulator_mode_constrain' makes pointer from integer without a cast
drivers/regulator/core.c:200: note: expected 'int *' but argument is of type 'unsigned int'
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@vega.(none)>

Current set_mode logic does not support 6030. The logic for 4030 is
not reusable for 6030 as the mode setting for 6030 now uses the new
CFG_STATE register. We hence rename the old get_status as being
specific to 4030.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NSaquib Herman <saquib@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@vega.(none)>

Current get_status logic does not support 6030 get_status.
The logic for 4030 is not reusable for 6030 as the status
check for 6030 now depends on the new CFG_STATE register.
We hence rename the old get_status as being specific to
4030 and remove the redundant check for the same.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NSaquib Herman <saquib@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@vega.(none)>

With TWL6030, it is not enough to ensure that the regulator is the
group of P1 group (CPU/Linux), but we need to check the state as far
as APP is concerned as well.

Split the current is_enabled to 6030 and 4030 specific ones. This
split impacts few macros and variables as well, but sets up the
stage for further fixes to set_mode and get_status in subsequent
patches.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NSaquib Herman <saquib@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@vega.(none)>

TWL6030 does not have remap register. The current implementation
causes value of remap to be written to state register, accidentally
causing the regulators which are probed to be switched on as well.
This is wrong as regulators should be controllable based on calls
to enable/disable for TWL regulator framework. Further, the values
initialized make no sense as well. We hence remove this from the
initalizers and also write to remap register only if the TWL
is 4030.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NSaquib Herman <saquib@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@vega.(none)>

TWL6030 requires an additional register write to CFG_STATE register
to explicitly state that the regulator is in a certain state. Merely
associating the regulator with the group is not enough. Add the
required register field definitions and fix the handling for
TWL6030 enable/disable.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NSaquib Herman <saquib@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@vega.(none)>

Otherwise, calling platform_get_drvdata in tps6105x_regulator_remove
returns NULL.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

If a mode requested by a consumer is not allowed by constraints
automatically fall back to a higher power mode if possible. This
ensures that consumers get at least the output they requested while
allowing machine drivers to transparently limit lower power modes
if required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Merge branch 'upstream/tidy-xen-mmu-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen

* 'upstream/tidy-xen-mmu-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen: fix compile without CONFIG_XEN_DEBUG_FS
  Use arbitrary_virt_to_machine() to deal with ioremapped pud updates.
  Use arbitrary_virt_to_machine() to deal with ioremapped pmd updates.
  xen/mmu: remove all ad-hoc stats stuff
  xen: use normal virt_to_machine for ptes
  xen: make a pile of mmu pvop functions static
  vmalloc: remove vmalloc_sync_all() from alloc_vm_area()
  xen: condense everything onto xen_set_pte
  xen: use mmu_update for xen_set_pte_at()
  xen: drop all the special iomap pte paths.

Right now security_get_user_sids() will pass in a NULL avd pointer to
avc_has_perm_noaudit(), which then forces that function to have a dummy
entry for that case and just generally test it.

Don't do it.  The normal callers all pass a real avd pointer, and this
helper function is incredibly hot.  So don't make avc_has_perm_noaudit()
do conditional stuff that isn't needed for the common case.

This also avoids some duplicated stack space.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
  Squashfs: update email address
  Squashfs: add extra sanity checks at mount time
  Squashfs: add sanity checks to fragment reading at mount time
  Squashfs: add sanity checks to lookup table reading at mount time
  Squashfs: add sanity checks to id reading at mount time
  Squashfs: add sanity checks to xattr reading at mount time
  Squashfs: reverse order of filesystem table reading
  Squashfs: move table allocation into squashfs_read_table()

The implementation of find_next_bit_le() on m68knommu is identical with
the generic implementation of find_next_bit_le().
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous style change enables to use asm-generic/bitops/le.h on s390.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous style change enables to use asm-generic/bitops/le.h on arm.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>