Add an interface-number sanity check before testing the device flags to
avoid relying on undefined behaviour when left shifting in case a device
uses an interface number greater than or equal to BITS_PER_LONG (i.e. 64
or 32).

Reported-by: syzbot+8881b478dad0a7971f79@syzkaller.appspotmail.com
Fixes: c3a65808 ("USB: serial: option: reimplement interface masking")
Cc: stable@vger.kernel.org
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Clean up dtr_rts() by renaming the port parameter and adding missing
whitespace.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add a helper function to be used to configure flow control.

The flow-control code was the last caller that relied on the
memset-on-failure behaviour of cp210x_read_reg_block(), which we can now
drop in favour of bailing out on errors when retrieving the flow-control
settings.

This should also simplify adding support for software flow control.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop some unnecessary flow-control debugging.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Unlike other drivers cp210x have been retrieving the current terminal
settings from the device on open and reflecting those in termios.

Due to how set_termios() used to be implemented, this saved a few
control requests on open but has instead caused problems like broken
flow control and has required adding workarounds for swapped
line-control in cp2108 and line-speed initialisation on cp2104.

This unusual implementation also complicates adding new features for no
good reason.

Rip out the corresponding code and the above mentioned workarounds and
instead initialise the terminal settings unconditionally on open.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Update the line-control settings in one request unconditionally instead
of setting the word-length, parity and stop-bit settings separately.

This avoids multiple requests when several settings are changed even if
this scheme could potentially also be used to detect unsupported device
settings. Since all device types but CP2101 appears to support all
settings, let's handle that one specifically and also report back the
unsupported settings properly through termios by clearing the
corresponding bits.

Also drop the related unnecessary debug printks.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Return early from set_termios() in case no relevant terminal settings
have changed.

This avoids testing each parameter in turn and specifically allows the
line-control handling to be cleaned up further.
Signed-off-by: NJohan Hovold <johan@kernel.org>

The parallel port restore operation currently defers writes
to a tasklet, if it sees a locked disconnect mutex. The
driver goes to a lot of trouble to ensure writes happen
in a non-blocking context, but things can be greatly
simplified if it's done in regular process context and
this is not a system performance critical path. As such,
instead of doing the state restore writes in softirq context,
use a workqueue and just do regular synchronous writes.

In addition to the cleanup, this also imposes less on the
overall system as tasklets have been deprecated because
of it's softirq implications, potentially blocking a higher
priority task from running.
Signed-off-by: NDavidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20201120045300.28804-1-dave@stgolabs.net
[johan: amend commit message ("softirq context")]
Signed-off-by: NJohan Hovold <johan@kernel.org>

The parallel-port restore operations is called when a driver claims the
port and is supposed to restore the provided state (e.g. saved when
releasing the port).

Fixes: b69578df ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org>     # 2.6.35
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The digi_acceleport driver is the only driver still using the port
write wake queue so move it to that driver's port data.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The driver must not call tty_wakeup() while holding its private lock as
line disciplines are allowed to call back into write() from
write_wakeup(), leading to a deadlock.

Also remove the unneeded work struct that was used to defer wakeup in
order to work around a possible race in ancient times (see comment about
n_tty write_chan() in commit 14b54e39 ("USB: serial: remove
changelogs and old todo entries")).

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop the redundant struct usb_serial pointer from the driver port data.
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Use the BIT() macro instead of open coding.
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Clean up comment style, remove some stale or redundant comments and drop
superfluous white space.
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop the separate Kconfig symbol for Xircom / Entrega and always include
support in the keyspan_pda driver.

Note that all configs that enabled CONFIG_USB_SERIAL_XIRCOM also enable
CONFIG_USB_SERIAL_KEYSPAN_PDA.
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Use the port write fifo and generic chars_and_buffer and write_room
implementations when writing. This not only allows for more efficient
transfers, but more importantly fixes the remaining issues related to
the conservative write_room() implementation which could prevent the
line discipline from making forward progress (e.g. waiting for n > 1
bytes of space to become available).

Note that this also allows using the driver for the system console
without dropping data when the write URB is busy (including when adding
carriage return on line feed).
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Increase the transmitter threshold so that writing isn't resumed until
128 bytes are available in the device buffer thereby allowing for larger
and more efficient transfers.
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix stalled writes by checking the available buffer space after
requesting an unthrottle notification in case the device buffer is
already empty so that no notification is ever sent (e.g. when doing
single character writes).

This also means we can drop the room query from write() which was
conditioned on in_interrupt() and prevented writing using this driver
from atomic contexts (e.g. PPP).
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add helper to retrieve the available device transfer-buffer space.
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The driver did not update its view of the available device buffer space
until write() was called in task context. This meant that write_room()
would return 0 even after the device had sent a write-unthrottle
notification, something which could lead to blocked writers not being
woken up (e.g. when using OPOST).

Note that we must also request an unthrottle notification is case a
write() request fills the device buffer exactly.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The driver's transmit-unthrottle work was never flushed on disconnect,
something which could lead to the driver port data being freed while the
unthrottle work is still scheduled.

Fix this by cancelling the unthrottle work when shutting down the port.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The driver's deferred write wakeup was never flushed on disconnect,
something which could lead to the driver port data being freed while the
wakeup work is still scheduled.

Fix this by using the usb-serial write wakeup which gets cancelled
properly on disconnect.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Make sure to clear the write-busy flag also in case no new data was
submitted due to lack of device buffer space so that writing is
resumed once space again becomes available.

Fixes: 507ca9bc ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.")
Cc: stable <stable@vger.kernel.org>     # 2.6.13
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The write() callback can be called in interrupt context (e.g. when used
as a console) so interrupts must be disabled while holding the port lock
to prevent a possible deadlock.

Fixes: e81ee637 ("usb-serial: possible irq lock inversion (PPP vs. usb/serial)")
Fixes: 507ca9bc ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.")
Cc: stable <stable@vger.kernel.org>     # 2.6.19
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Commit c528fcb1 ("USB: serial: keyspan_pda: fix receive sanity
checks") broke write-unthrottle handling by dropping well-formed
unthrottle-interrupt packets which are precisely two bytes long. This
could lead to blocked writers not being woken up when buffer space again
becomes available.

Instead, stop unconditionally printing the third byte which is
(presumably) only valid on modem-line changes.

Fixes: c528fcb1 ("USB: serial: keyspan_pda: fix receive sanity checks")
Cc: stable <stable@vger.kernel.org>     # 4.11
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

A break is not needed if it is preceded by a return.
Signed-off-by: NTom Rix <trix@redhat.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

The debug printk() in digi_write() prints in_interrupt() as context
information. This information is imprecise as it does not distinguish
between hard-IRQ or disabled bottom half and it does not consider
disabled interrupts or preemption. It is not really helpful.

Remove the in_interrupt() printout.
Signed-off-by: NAhmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20201026140313.dpg3hkhkje2os4hw@linutronix.de
[ johan: amend commit message ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

In order to enable -Wimplicit-fallthrough for Clang[1], replace the
existing /* FALLTHROUGH */ comment with the new pseudo-keyword
macro fallthrough[2].

[1] https://git.kernel.org/linus/e2079e93f562c7f7a030eb7642017ee5eabaaa10
[2] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20201008222849.GA18634@embeddedorSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The QCOM SPMI typec driver handles the role and orientation detection, and
notifies client drivers using the USB role switch framework.   It registers
as a typec port, so orientation can be communicated using the typec switch
APIs.  The driver also attains a handle to the VBUS output regulator, so it
can enable/disable the VBUS source when acting as a host/device.
Signed-off-by: NWesley Cheng <wcheng@codeaurora.org>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NStephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201008235934.8931-2-wcheng@codeaurora.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add usb ids of the Cellient MPL200 card.
Signed-off-by: NWilken Gottwalt <wilken.gottwalt@mailbox.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/3db5418fe9e516f4b290736c5a199c9796025e3c.1601715478.git.wilken.gottwalt@mailbox.orgSigned-off-by: NJohan Hovold <johan@kernel.org>

Upon receiving ALERT_EXTENDED.TCPC_SINK_FAST_ROLE_SWAP signal
tcpm to start Sink fast role swap signal.

Inform when TCPM is sourcing vbus.
Signed-off-by: NBadhri Jagan Sridharan <badhri@google.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-9-badhri@google.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement tcpc.enable_frs to enable TCPC to receive
Fast role swap signal.

Additionally set the sink disconnect threshold to 4v
to prevent disconnect during Fast Role swap.
Signed-off-by: NBadhri Jagan Sridharan <badhri@google.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-8-badhri@google.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.

Once the explicit contract is negotiated, sink port is
expected to query the source port for sink caps to
determine whether the source is FRS capable.
Bits 23 & 24 of fixed pdo of the sink caps from the source, when
set, indicates the current needed by the source when fast role
swap is in progress(Implicit contract phasae). 0 indicates that
the source does not support Fast Role Swap.

Upon receiving the FRS signal from the source,
TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.

1. TCPM sends FRS PD message: FR_SWAP_SEND
2. If response is not received within the expiry of
   SenderResponseTimer, Error recovery is triggered.:
   FR_SWAP_SEND_TIMEOUT
3. Upon receipt of the accept message, TCPM waits for
   PSSourceOffTimer for PS_READY message from the partner:
   FR_SWAP_SNK_SRC_NEW_SINK_READY.

TCPC is expected to autonomously turn on vbus once the FRS
signal is received and vbus voltage falls below vsafe5v within
tSrcFrSwap. This is different from traditional power role swap
where the vbus sourcing is turned on by TCPM.

4. By this time, TCPC most likely would have started to
   source vbus, TCPM waits for tSrcFrSwap to see  if the
   lower level TCPC driver signals TCPM_SOURCING_VBUS event:
   FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
   changes the CC pin from Rd to Rp. This is the end of fast
   role swap sequence and TCPM initiates the sequnce to negotiate
   explicit contract by transitioning into SRC_STARTUP after
   SwapSrcStart.

The code is written based on the sequence described in "Figure 8-107:
Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
USB Power Delivery Specification Revision 3.0, Version 1.2.
Signed-off-by: NBadhri Jagan Sridharan <badhri@google.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-7-badhri@google.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Chip level TCPC driver for Maxim's TCPCI implementation.
This TCPC implementation does not support the following
commands: COMMAND.SinkVbus, COMMAND.SourceVbusDefaultVoltage,
COMMAND.SourceVbusHighVoltage. Instead the sinking and sourcing
from vbus is supported by writes to custom registers.
Signed-off-by: NBadhri Jagan Sridharan <badhri@google.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-5-badhri@google.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

set_vbus callback allows TCPC which are TCPCI based, however,
does not support turning on sink and source mode through
Command.SinkVbus and Command.SourceVbusDefaultVoltage.
Signed-off-by: NBadhri Jagan Sridharan <badhri@google.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-3-badhri@google.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow chip level drivers to retrieve reference to tcpm_port.
Signed-off-by: NBadhri Jagan Sridharan <badhri@google.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-2-badhri@google.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

kcov testing uncovered call to usb_hcd_giveback_urb() without disabling
interrupts.

Link: https://lore.kernel.org/linux-usb/CAAeHK+wb4k-LGTjK9F5YbJNviF_+yU+wE_=Vpo9Rn7KFN8vG6Q@mail.gmail.com/

usb_hcd_giveback_urb() is called from vhci's urb_enqueue, when it
determines it doesn't need to xmit the urb and can give it back.
This path runs in task context.

Disable irqs around usb_hcd_giveback_urb() call.
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NShuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201006223914.39257-1-skhan@linuxfoundation.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ES58X devices has a CDC ACM interface (used for debug
purpose). During probing, the device is thus recognized as USB Modem
(CDC ACM), preventing the etas-es58x module to load:
  usbcore: registered new interface driver etas_es58x
  usb 1-1.1: new full-speed USB device number 14 using xhci_hcd
  usb 1-1.1: New USB device found, idVendor=108c, idProduct=0159, bcdDevice= 1.00
  usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
  usb 1-1.1: Product: ES581.4
  usb 1-1.1: Manufacturer: ETAS GmbH
  usb 1-1.1: SerialNumber: 2204355
  cdc_acm 1-1.1:1.0: No union descriptor, testing for castrated device
  cdc_acm 1-1.1:1.0: ttyACM0: USB ACM device

Thus, these have been added to the ignore list in
drivers/usb/class/cdc-acm.c

N.B. Future firmware release of the ES58X will remove the CDC-ACM
interface.

`lsusb -v` of the three devices variant (ES581.4, ES582.1 and
ES584.1):

  Bus 001 Device 011: ID 108c:0159 Robert Bosch GmbH ES581.4
  Device Descriptor:
    bLength                18
    bDescriptorType         1
    bcdUSB               1.10
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    idVendor           0x108c Robert Bosch GmbH
    idProduct          0x0159
    bcdDevice            1.00
    iManufacturer           1 ETAS GmbH
    iProduct                2 ES581.4
    iSerial                 3 2204355
    bNumConfigurations      1
    Configuration Descriptor:
      bLength                 9
      bDescriptorType         2
      wTotalLength       0x0035
      bNumInterfaces          1
      bConfigurationValue     1
      iConfiguration          5 Bus Powered Configuration
      bmAttributes         0x80
        (Bus Powered)
      MaxPower              100mA
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        0
        bAlternateSetting       0
        bNumEndpoints           3
        bInterfaceClass         2 Communications
        bInterfaceSubClass      2 Abstract (modem)
        bInterfaceProtocol      0
        iInterface              4 ACM Control Interface
        CDC Header:
          bcdCDC               1.10
        CDC Call Management:
          bmCapabilities       0x01
            call management
          bDataInterface          0
        CDC ACM:
          bmCapabilities       0x06
            sends break
            line coding and serial state
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x81  EP 1 IN
          bmAttributes            3
            Transfer Type            Interrupt
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0010  1x 16 bytes
          bInterval              10
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x82  EP 2 IN
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0040  1x 64 bytes
          bInterval               0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x03  EP 3 OUT
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0040  1x 64 bytes
          bInterval               0
  Device Status:     0x0000
    (Bus Powered)

  Bus 001 Device 012: ID 108c:0168 Robert Bosch GmbH ES582
  Device Descriptor:
    bLength                18
    bDescriptorType         1
    bcdUSB               2.00
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    idVendor           0x108c Robert Bosch GmbH
    idProduct          0x0168
    bcdDevice            1.00
    iManufacturer           1 ETAS GmbH
    iProduct                2 ES582
    iSerial                 3 0108933
    bNumConfigurations      1
    Configuration Descriptor:
      bLength                 9
      bDescriptorType         2
      wTotalLength       0x0043
      bNumInterfaces          2
      bConfigurationValue     1
      iConfiguration          0
      bmAttributes         0x80
        (Bus Powered)
      MaxPower              500mA
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        0
        bAlternateSetting       0
        bNumEndpoints           1
        bInterfaceClass         2 Communications
        bInterfaceSubClass      2 Abstract (modem)
        bInterfaceProtocol      1 AT-commands (v.25ter)
        iInterface              0
        CDC Header:
          bcdCDC               1.10
        CDC ACM:
          bmCapabilities       0x02
            line coding and serial state
        CDC Union:
          bMasterInterface        0
          bSlaveInterface         1
        CDC Call Management:
          bmCapabilities       0x03
            call management
            use DataInterface
          bDataInterface          1
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x83  EP 3 IN
          bmAttributes            3
            Transfer Type            Interrupt
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0040  1x 64 bytes
          bInterval              16
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        1
        bAlternateSetting       0
        bNumEndpoints           2
        bInterfaceClass        10 CDC Data
        bInterfaceSubClass      0
        bInterfaceProtocol      0
        iInterface              0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x81  EP 1 IN
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0200  1x 512 bytes
          bInterval               0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x02  EP 2 OUT
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0200  1x 512 bytes
          bInterval               0
  Device Qualifier (for other device speed):
    bLength                10
    bDescriptorType         6
    bcdUSB               2.00
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    bNumConfigurations      1
  Device Status:     0x0000
    (Bus Powered)

  Bus 001 Device 013: ID 108c:0169 Robert Bosch GmbH ES584.1
  Device Descriptor:
    bLength                18
    bDescriptorType         1
    bcdUSB               2.00
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    idVendor           0x108c Robert Bosch GmbH
    idProduct          0x0169
    bcdDevice            1.00
    iManufacturer           1 ETAS GmbH
    iProduct                2 ES584.1
    iSerial                 3 0100320
    bNumConfigurations      1
    Configuration Descriptor:
      bLength                 9
      bDescriptorType         2
      wTotalLength       0x0043
      bNumInterfaces          2
      bConfigurationValue     1
      iConfiguration          0
      bmAttributes         0x80
        (Bus Powered)
      MaxPower              500mA
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        0
        bAlternateSetting       0
        bNumEndpoints           1
        bInterfaceClass         2 Communications
        bInterfaceSubClass      2 Abstract (modem)
        bInterfaceProtocol      1 AT-commands (v.25ter)
        iInterface              0
        CDC Header:
          bcdCDC               1.10
        CDC ACM:
          bmCapabilities       0x02
            line coding and serial state
        CDC Union:
          bMasterInterface        0
          bSlaveInterface         1
        CDC Call Management:
          bmCapabilities       0x03
            call management
            use DataInterface
          bDataInterface          1
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x83  EP 3 IN
          bmAttributes            3
            Transfer Type            Interrupt
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0040  1x 64 bytes
          bInterval              16
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        1
        bAlternateSetting       0
        bNumEndpoints           2
        bInterfaceClass        10 CDC Data
        bInterfaceSubClass      0
        bInterfaceProtocol      0
        iInterface              0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x81  EP 1 IN
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0200  1x 512 bytes
          bInterval               0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x02  EP 2 OUT
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0200  1x 512 bytes
          bInterval               0
  Device Qualifier (for other device speed):
    bLength                10
    bDescriptorType         6
    bcdUSB               2.00
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    bNumConfigurations      1
  Device Status:     0x0000
    (Bus Powered)
Signed-off-by: NVincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201002154219.4887-8-mailhol.vincent@wanadoo.frSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ftdi_determine_type() function had this construct in it to get the
number of the interface it is operating on:

  inter = serial->interface->altsetting->desc.bInterfaceNumber;

Elsewhere in this driver cur_altsetting is used instead for this
purpose.  Change ftdi_determine_type() to use cur_altsetting
for consistency.
Signed-off-by: NMychaela N. Falconia <falcon@freecalypso.org>
[ johan: fix old style issues; drop braces and random white space ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

This commit adds the following Telit FT980-KS composition:

0x1054: rndis, diag, adb, nmea, modem, modem, aux

AT commands can be sent to /dev/ttyUSB2.
Signed-off-by: NLeonid Bloch <lb.workbox@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/ce86bc05-f4e2-b199-0cdc-792715e3f275@asocscloud.com
Link: https://lore.kernel.org/r/20201004155813.2342-1-lb.workbox@gmail.comSigned-off-by: NJohan Hovold <johan@kernel.org>