Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:

- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
  as part of net driver modules.  (This also fixes cases where the PTP
  subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
  drivers but are built separately
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP hardware clock drivers that select PTP_1588_CLOCK must currently
also select PPS.  For those drivers that don't, the user must enable
PPS, then enable PTP_1588_CLOCK, then the driver.  Simplify things for
developers and users by putting this selection in one place.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These are now established subsystems, and we want drivers to be able
to select PPS and PTP_1588_CLOCK without depending on EXPERIMENTAL.
Further, the use of EXPERIMENTAL is now deprecated in general.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements a simple multiqueue flow steering policy - tx follows rx
for tun/tap. The idea is simple, it just choose the txq based on which rxq it
comes. The flow were identified through the rxhash of a skb, and the hash to
queue mapping were recorded in a hlist with an ageing timer to retire the
mapping. The mapping were created when tun receives packet from userspace, and
was quired in .ndo_select_queue().

I run co-current TCP_CRR test and didn't see any mapping manipulation helpers in
perf top, so the overhead could be negelected.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes usespace may need to active/deactive a queue, this could be done by
detaching and attaching a file from tuntap device.

This patch introduces a new ioctls - TUNSETQUEUE which could be used to do
this. Flag IFF_ATTACH_QUEUE were introduced to do attaching while
IFF_DETACH_QUEUE were introduced to do the detaching.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts tun/tap to a multiqueue devices and expose the multiqueue
queues as multiple file descriptors to userspace. Internally, each tun_file were
abstracted as a queue, and an array of pointers to tun_file structurs were
stored in tun_structure device, so multiple tun_files were allowed to be
attached to the device as multiple queues.

When choosing txq, we first try to identify a flow through its rxhash, if it
does not have such one, we could try recorded rxq and then use them to choose
the transmit queue. This policy may be changed in the future.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RCU were introduced in this patch to synchronize the dereferences between
tun_struct and tun_file. All tun_{get|put} were replaced with RCU, the
dereference from one to other must be done under rtnl lock or rcu read critical
region.

This is needed for the following patches since the one of the goal of multiqueue
tuntap is to allow adding or removing queues during workload. Without RCU,
control path would hold tx locks when adding or removing queues (which may cause
sme delay) and it's hard to change the number of queues without stopping the net
device. With the help of rcu, there's also no need for tun_file hold an refcnt
to tun_struct.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current tuntap makes use of the socket receive queue as its tx queue. To
implement multiple tx queues for tuntap and enable the ability of adding and
removing queues during workload, the first step is to move the socket related
structures to tun_file. Then we could let multiple fds/sockets to be attached to
the tuntap.

This patch removes tun_sock and moves socket related structures from tun_sock or
tun_struct to tun_file. Two exceptions are tap_filter and sock_fprog, they are
still kept in tun_structure since they are used to filter packets for the net
device instead of per transmit queue (at least I see no requirements for
them). After those changes, socket were created and destroyed during file open
and close (instead of device creation and destroy), the socket structures could
be dereferenced from tun_file instead of the file of tun_struct structure
itself.

For persisent device, since we purge during datching and wouldn't queue any
packets when no interface were attached, there's no behaviod changes before and
after this patch, so the changes were transparent to the userspace. To keep the
attributes such as sndbuf, socket filter and vnet header, those would be
re-initialize after a new interface were attached to an persist device.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following build failure on S390:
  In file included from drivers/net/ethernet/cadence/at91_ether.c:35:0:
   drivers/net/ethernet/cadence/macb.h: In function 'macb_is_gem':
   drivers/net/ethernet/cadence/macb.h:563:2: error: implicit declaration of function '__raw_readl' [-Werror=implicit-function-declaration]
   drivers/net/ethernet/cadence/at91_ether.c: In function 'update_mac_address':
   drivers/net/ethernet/cadence/at91_ether.c:119:2: error: implicit declaration of function '__raw_writel' [-Werror=implicit-function-declaration]
   cc1: some warnings being treated as errors
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware doesn't support controlling pause frames autoneg, so
report that back correctly to userspace.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use the module_pci_driver macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use the module_pci_driver macro to make the code simpler
by eliminating the module_init and module_exit calls
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable retval is initialized but never used
otherwise, so remove the unused variable.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for wol wakeup on unicast, broadcast,
multicast and arp frames.

The wakeup filter code isn't pretty, but it works.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the net device ops to manage the embedded
hardware bridge on ixgbe devices. With this patch the bridge
mode can be toggled between VEB and VEPA to support stacking
macvlan devices or using the embedded switch without any SW
component in 802.1Qbg/br environments.

Additionally, this adds source address pruning to the ixgbevf
driver to prune any frames sent back from a reflective relay on
the switch. This is required because the existing hardware does
not support this. Without it frames get pushed into the stack
with its own src mac which is invalid per 802.1Qbg VEPA
definition.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change fixes a sparse warning triggered by us casting the timestamp in
the packet as a u64 instead of as a __le64.  This change corrects that in
order to resolve the sparse warning.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are multiple places in our device nvm where the version is stored.
This update fixes some output errors with some types of images and
refactors the way the version data is gathered and stored for ethtool output.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Newer devices supported by igb can support auto-crossover detection in
forced operation modes. Enable this in the driver, rather than clobbering
this functionality in forced operation.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ignoring the return value from a call to the kernel dma_map API functions
can cause data corruption and system instability.  Check the return value
and take appropriate action.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver should not forward LLDP type frames.  Inspect the ether type and
do not send if it is an LLDP ethertype frame.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Hw timestamping code caused performance regression in ixgbe driver when the
timestamping is not enabled. The culprit is IXGBE_READ_REG call in the Rx
path which is executed for every received skb. This call is not needed when
the timestamping is disabled or for non-ptp packets.

netperf results:

The ixgbe side of the connection was acting as a server, the netperf command
line on the other side was:
netperf -H 192.168.1.23 -T0,0 -t UDP_STREAM -l 20

The values below mean throughput as reported by netperf (local/remote), for
3 runs, with timestamping not enabled.

3.7.0-rc1+ with CONFIG_IXGBE_PTP off:
5373.83 / 3329.32
5721.88 / 3033.89
5653.42 / 3112.38

3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5233.64 / 1226.85
5448.67 / 1039.32
5421.36 / 1095.66

Patched 3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5594.72 / 2942.53
5428.95 / 3110.16
5343.56 / 3200.48
Reported-by: NJesper Brouer <jbrouer@redhat.com>
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NAndy Gospodarek <gospo@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adds/updates ASCII descriptor maps for 82598 and 82599 Tx/Rx descriptors.
Current descriptor maps were out of date for 82598 and incorrect for
82599.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that compare the total_rx_packets cleaned to budget
instead of decrementing budget.  The advantage to this approach is that budget
can now be const and we only end up modifying total_rx_packets instead of
modifying both it and budget.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When setting a MAC filter for the VF the function should return a success
or failure code, not the index of the new filter.  It causes spurious NACK
returns to the VF driver.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch simplifies the check for calling en/disable_tx_laser() function
pointer. The pointer is only set on parts that can use it.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In SR-IOV mode the PF driver acts as the uplink port and is
used to send control packets e.g. lldpad, stp, etc.

   eth0.1     eth0.2     eth0
   VF         VF         PF
   |          |          |   <-- stand-in for uplink
   |          |          |
  --------------------------
  |  Embedded Switch       |
  --------------------------
              |
             MAC   <-- uplink

But the embedded switch is setup to forward multicast addresses
to all interfaces both VFs and PF and onto the physical link.
This results in reserved MAC addresses used by control protocols
to be forwarded over the switch onto the VF.

In the LLDP case the PF sends an LLDPDU and it is currently
being forwarded to all the VFs who then see the PF as a peer.
This is incorrect.

This patch adds the multicast addresses to the RAR table in the
hardware to prevent this behavior.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function to set the macvlan filter should return success or failure
instead of the index of the filter.  The message processing function was
misinterpreting the index as a non-zero return code indicating failure and
NACKing MAC filter set messages that actually succeeded.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling the ixgbe_reset_pipeline_82599 function will ensure a full pipeline
reset on all 82599 devices.  This is necessary to avoid possible link issues.
Since this patch accomplishes this by modifying AUTOC.LMS we need to wrap
all AUTOC writes when LESM is enabled.

v2- fix LMS behaviour based on feedback by Martin Josefsson

CC: Martin Josefsson <gandalf@mjufs.se>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removes the warnings

 drivers/net/usb/sierra_net.c:343:45: warning: incorrect type in assignment (different base types)
 drivers/net/usb/sierra_net.c:343:45:    expected unsigned short [unsigned] [short] [usertype] <noident>
 drivers/net/usb/sierra_net.c:343:45:    got restricted __be16 [usertype] <noident>

and

 drivers/net/usb/sierra_net.c:658:18: warning: cast to restricted __le16
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the sparse warning

 drivers/net/usb/cdc_ncm.c:836:9: warning: context imbalance in 'cdc_ncm_txpath_bh' - different lock contexts for basic block
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Probably doesn't matter much since the value is used as a
boolean anyway, but it removes the sparse warning:

 drivers/net/usb/cdc_ncm.c:1090:32: warning: incorrect type in assignment (different base types)
 drivers/net/usb/cdc_ncm.c:1090:32:    expected unsigned short [unsigned] [usertype] connected
 drivers/net/usb/cdc_ncm.c:1090:32:    got restricted __le16 [usertype] wValue
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cgroup logic part of net_cls is very similar as the one in
net_prio. Let's stream line the net_cls logic with the net_prio one.

The net_prio update logic was changed by following commit (note there
were some changes necessary later on)

commit 406a3c63
Author: John Fastabend <john.r.fastabend@intel.com>
Date:   Fri Jul 20 10:39:25 2012 +0000

    net: netprio_cgroup: rework update socket logic

    Instead of updating the sk_cgrp_prioidx struct field on every send
    this only updates the field when a task is moved via cgroup
    infrastructure.

    This allows sockets that may be used by a kernel worker thread
    to be managed. For example in the iscsi case today a user can
    put iscsid in a netprio cgroup and control traffic will be sent
    with the correct sk_cgrp_prioidx value set but as soon as data
    is sent the kernel worker thread isssues a send and sk_cgrp_prioidx
    is updated with the kernel worker threads value which is the
    default case.

    It seems more correct to only update the field when the user
    explicitly sets it via control group infrastructure. This allows
    the users to manage sockets that may be used with other threads.

Since classid is now updated when the task is moved between the
cgroups, we don't have to call sock_update_classid() from various
places to ensure we always using the latest classid value.

[v2: Use iterate_fd() instead of open coding]
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Cc:  Li Zefan <lizefan@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Joe Perches <joe@perches.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <netdev@vger.kernel.org>
Cc: <cgroups@vger.kernel.org>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sock_update_classid() assumes that the update operation always are
applied on the current task. sock_update_classid() needs to know on
which tasks to work on in order to be able to migrate task between
cgroups using the struct cgroup_subsys attach() callback.
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Joe Perches <joe@perches.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <netdev@vger.kernel.org>
Cc: <cgroups@vger.kernel.org>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>