With the new i.mx clock framework, we need to use
clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Like e65cc194 (ahci: Enable SB600 64bit
DMA on MSI K9A2 Platinum) and 3c4aa91f
(ahci: Enable SB600 64bit DMA on Asus M3A), this patch enables 64bit DMA
for the AHCI SATA controller of another board that has the SB600
southbridge.

In this case though we're enabling 64bit DMA for another MSI motherboard,
the K9AGM2 or MS-7327. It is new enough that all of the BIOS releases
since the initial release (1.0 from 2007-02-09) work correctly with 64bit
DMA enabled.
Signed-off-by: NMark Nelson <mdnelson8@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.

Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Signed-off-by: NDaniel J Blueman <daniel@quora.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 6b66d958 should not have changed
EXPORT_SYMBOL_GPL to EXPORT_SYMBOL.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Adds inline for ata_acpi_unregister/ata_acpi_bind/ata_acpi_unbind
in drivers/ata/libata.h for !CONFIG_ATA_ACPI to fix below warnings.

warning: 'ata_acpi_unregister' defined but not used [-Wunused-function]
warning: 'ata_acpi_bind' defined but not used [-Wunused-function]
warning: 'ata_acpi_unbind' defined but not used [-Wunused-function]
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

If ATA device supports "Device Attention", then tell scsi layer that
the device supports runtime power off.
Signed-off-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add a new flag ATA_DFLAG_DA to indicate that device supports "Device
Attention".
Acked-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ATA port may support runtime D3Cold state, for example, Zero-power ODD case.
This patch adds wakeup notifier and enable/disable run_wake during
supend/resume.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently, ata_acpi_set_state() only sets acpi sate for IDE port.
Remove this limitation.
Acked-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Now that we have the ability to directly glue the ACPI namespace to the
driver model in libata, we don't need the custom code to handle the same
thing. Remove it and migrate the functions over to the new code.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NHolger Macht <holger@homac.de>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Associate the ACPI device tree and libata devices.
This patch uses the generic ACPI glue framework to do so.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NHolger Macht <holger@homac.de>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For being able to bind ata devices against acpi devices, scsi_bus_type
needs to be set as bus in struct acpi_bus_type. So add wrapper to
scsi_lib to accomplish that.
Signed-off-by: NHolger Macht <holger@homac.de>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Pull hwmon changes from Guenter Roeck:
 "Just e-mail address updates"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: Update my e-mail address
  hwmon: (applesmc) correct email address for Jesper Juhl

Pull watchdog fixes from Wim Van Sebroeck:
 "This fixes:
   - the WDIOC_GETSTATUS return value
   - the unregister of all NMI events on exit
   - the loading of the iTCO_wdt driver after the conversion to the
     lpc_ich mfd model."

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: core: fix WDIOC_GETSTATUS return value
  watchdog: hpwdt: Unregister NMI events on exit.
  watchdog: iTCO_wdt: add platform driver module alias

Pull UDF fixes from Jan Kara:
 "Make UDF more robust in presence of corrupted filesystem"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  udf: Fortify loading of sparing table
  udf: Avoid run away loop when partition table length is corrupted
  udf: Use 'ret' instead of abusing 'i' in udf_load_logicalvol()

Pull ubi/ubifs fixes from Artem Bityutskiy:
 "Fix the debugfs regression - we never enable it because incorrect
  'IS_ENABLED()' macro usage: should be 'IS_ENABLED(CONFIG_DEBUG_FS)',
  but we had 'IS_ENABLED(DEBUG_FS)'.  Also fix incorrect assertion."

* tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs:
  UBI: correct usage of IS_ENABLED()
  UBIFS: correct usage of IS_ENABLED()
  UBIFS: fix assertion

In commit 7a879824 we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.
Signed-off-by: NThomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Pull drm fixes from Dave Airlie:
 "Nearly all intel, one missing license header in nouveau, nothing
  majorly earth shattering."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  Revert "drm/i915: allow PCH PWM override on IVB"
  drm/nouveau: add license header to prime.
  drm/i915: Fix eDP blank screen after S3 resume on HP desktops
  drm/i915: rip out the PM_IIR WARN

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
  sh: Convert sh_clk_mstp32_register to sh_clk_mstp_register
  sh: kfr2r09: fix compile breakage

Pull networking update from David Miller:

 1) Pairing and deadlock fixes in bluetooth from Johan Hedberg.

 2) Add device IDs for AR3011 and AR3012 bluetooth chips.  From
    Giancarlo Formicuccia and Marek Vasut.

 3) Fix wireless regulatory deadlock, from Eliad Peller.

 4) Fix full TX ring panic in bnx2x driver, from Eric Dumazet.

 5) Revert the two commits that added skb_orphan_try(), it causes
    erratic bonding behavior with UDP clients and the gains it used to
    give are mostly no longer happening due to how BQL works.  From Eric
    Dumazet.

 6) It took two tries, but Thomas Graf fixed a problem wherein we
    registered ipv6 routing procfs files before their backend data were
    initialized properly.

 7) Fix max GSO size setting in be2net, from Sarveshwar Bandi.

 8) PHY device id mask is wrong for KSZ9021 and KS8001 chips, fix from
    Jason Wang.

 9) Fix use of stale SKB data pointer after skb_linearize() call in
    batman-adv, from Antonio Quartulli.

10) Fix memory leak in IXGBE due to missing __GFP_COMP, from Alexander
    Duyck.

11) Fix probing of Gobi devices in qmi_wwan usbnet driver, from Bjørn
    Mork.

12) Fix suspend/resume and open failure handling in usbnet from Ming
    Lei.

13) Attempt to fix device r8169 hangs for certain chips, from Francois
    Romieu.

14) Fix advancement of RX dirty pointer in some situations in sh_eth
    driver, from Yoshihiro Shimoda.

15) Attempt to fix restart of IPV6 routing table dumps when there is an
    intervening table update.  From Eric Dumazet.

16) Respect security_inet_conn_request() return value in ipv6 TCP.  From
    Neal Cardwell.

17) Add another iPAD device ID to ipheth driver, from Davide Gerhard.

18) Fix access to freed SKB in l2tp_eth_dev_xmit(), and fix l2tp lockdep
    splats, from Eric Dumazet.

19) Make sure all bridge devices, regardless of whether they were
    created via netlink or ioctls, have their rtnetlink ops hooked up.
    From Thomas Graf and Stephen Hemminger.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
  9p: fix min_t() casting in p9pdu_vwritef()
  can: flexcan: use be32_to_cpup to handle the value of dt entry
  xen/netfront: teardown the device before unregistering it.
  bridge: Assign rtnl_link_ops to bridge devices created via ioctl (v2)
  vhost: use USER_DS in vhost_worker thread
  ixgbe: Do not pad FCoE frames as this can cause issues with FCoE DDP
  net: l2tp_eth: use LLTX to avoid LOCKDEP splats
  mac802154: add missed braces
  net: l2tp_eth: fix l2tp_eth_dev_xmit race
  net/mlx4_en: Release QP range in free_resources
  net/mlx4: Use single completion vector after NOP failure
  net/mlx4_en: Set correct port parameters during device initialization
  ipheth: add support for iPad
  caif-hsi: Add missing return in error path
  caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost
  caif: Clear shutdown mask to zero at reconnect.
  tcp: heed result of security_inet_conn_request() in tcp_v6_conn_request()
  ipv6: fib: fix fib dump restart
  batman-adv: fix race condition in TT full-table replacement
  batman-adv: only drop packets of known wifi clients
  ...

Add sanity checks when loading sparing table from disk to avoid accessing
unallocated memory or writing to it.
Signed-off-by: NJan Kara <jack@suse.cz>

Check provided length of partition table so that (possibly maliciously)
corrupted partition table cannot cause accessing data beyond current buffer.
Signed-off-by: NJan Kara <jack@suse.cz>

Signed-off-by: NJan Kara <jack@suse.cz>

sh_clk_mstp32_register is deprecated. This convert to sh_clk_mstp_register.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix compile breakage caused by

commit aa82f9fc
Author: Paul Mundt <lethal@linux-sh.org>

    sh: kfr2r09 evt2irq migration.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Marc Kleine-Budde says:

====================
here's a patch intended for v3.5, targeting net/master. Hui Wang has
found and fixed an endianness problem in the device tree handling in
the flexcan driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I don't think we're actually likely to hit this limit but if we do
then the comparison should be done as size_t.  The original code
is equivalent to:
        len = strlen(sptr) % USHRT_MAX;
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull USB fixes from Greg Kroah-Hartman:
 "Here are some small USB gadget bugfixes, and a few new USB device ids
  added to some drivers for the 3.5-rc5 release.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: CP210x Add 10 Device IDs
  USB: option: Add USB ID for Novatel Ovation MC551
  usb: phy: Fix Kconfig dependency for Phy drivers
  usb-storage: revert commit afff07e6 (Add 090c:1000 to unusal-devs)
  SCSI & usb-storage: add try_rc_10_first flag
  usb: musb: host: release dma channels if no active io
  usb: gadget: lpc32xx_udc: fix build error with debugfs enabled
  usb: otg: twl6030-usb: Fix twl writes
  USB: option: add id for Cellient MEN-200
  usb: dwc3: fix giveback of queued request in ep_dequeue
  usb: gadget: Complete fsl qe/udc driver conversion

Pull sound fixes from Takashi Iwai:
 "Here you find quite a few changes for HD-audio and a copule of quirk
  additions for USB-audio.  All reasonably small and/or trivial."

* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix power-map regression for HP dv6 & co
  ALSA: hda - Initialize caches at codec reconfiguration
  ALSA: hda - Fix memory leaks at module unload
  ALSA: hda - Fix memory leaks in Realtek & Conexant codec parsers
  ALSA: hda - Add Realtek ALC280 codec support
  ALSA: hda - Remove obsoleted CONFIG_SND_HDA_ENABLE_REALTEK_QUIRKS
  ASoC: wm8994: remove duplicate code
  ALSA: usb-audio: add BOSS GT-100 support
  ALSA: HDA: Add inverted internal mic quirk for Lenovo S205
  ALSA: hda - Fix ALC272X codec detection
  ALSA: snd_usb_audio: ignore ctrl errors on QuickCam Pro for Notebooks
  ALSA: snd_usb_audio: ignore ctrl errors on QuickCam E3500

Pull a m68knommu fix from Greg Ungerer:
 "It contains a single fix for breakage using the Freescale FEC eth
  driver on ColdFire CPUs."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: define a local devm_clk_get() function

Pull MMC fixes from Chris Ball:

 - omap_hsmmc: Using AUTO_CMD12 (enabled by default in 3.5-rc1) has
   been found to cause data corruption on the BeagleBoard, but no
   other OMAP boards so far.  Revert the patch until there's a root
   cause explanation that makes sense, at which point we might
   decide to use a blacklist or whitelist.

 - mmc_block: Fix incorrect data timeouts for the case of multiblock
   (ACMD22) writes for block-addressed cards.

* tag 'mmc-fixes-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  Revert "mmc: omap_hsmmc: Enable Auto CMD12"
  mmc: block: fix the data timeout issue with ACMD22

Pull clk common framework fixes from Mike Turquette:
 "This contains three NULL pointer fixes and two device regression
  fixups.

  Two NULL pointer dereferences were in the common clk core due to lack
  of sanity checking and the third NPD was in the mxs-specific clock
  code due to incorrect use of __initdata.

  The device regressions were the result of improper data: a wrong
  string name for matching DT data broke the SPEAr ethernet controller
  and another string matching problem in the mxs clock data resulted in
  a broken MMC controller."

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
  clk: mxs: fix clock lookup after freeing init memory
  clk: mxs: fix ref_io clock definition
  clk: Check parent for NULL in clk_change_rate
  clk: Allow late cache allocation for clk->parents
  clk: SPEAr600: Fix ethernet clock name for DT based probing

This script lacks an executable bit.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Daniel writes:
"Two tiny patches and one revert:
- Kill a bogus error message introduced in 3.4, further Bspec reading
  indicates that this is how the hw is supposed to work.
- Reorder one backlight register restore, fixing broken backlight on some
  machines after resume.
- Revert a hack from Jesse for ivb backlight control - it breaks the
  backlight controls on my shiny new ivb laptop."

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  Revert "drm/i915: allow PCH PWM override on IVB"
  drm/i915: Fix eDP blank screen after S3 resume on HP desktops
  drm/i915: rip out the PM_IIR WARN

This reverts commit f82cfb6b.

This breaks the backlight controls on my IVB asus zenbook with an eDP
panel.

I guess the right fix would be to read this bit and use either the pch
or the cpu register to frob the backlight values. But that is stuff
for -next.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Commit "e9b4cf20 UBI: fix debugfs-less systems support" fixed one
regression but introduced a different regression - the debugfs is now always
compiled out. Root cause: IS_ENABLED() arguments should be used with the
CONFIG_* prefix.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>