This patch enables the driver for the SDHCI controller found on the
Marvell Armada 3700 and 7K/8K ARM64 SoCs.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The MVPP2 network driver is used for the ARM64 Marvell Armada 7K and 8K
platforms, so enable it in the arm64 defconfig.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Now that the Armada 37xx SoCs support the i2c pxa driver, enable it by
default.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Now that the Armada 37xx SoCs support the mvneta driver, enable it by
default. It is especially useful when booting on an NFS root.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The PMULL based CRC32 implementation already contains code based on the
separate, optional CRC32 instructions to fallback to when operating on
small quantities of data. We can expose these routines directly on systems
that lack the 64x64 PMULL instructions but do implement the CRC32 ones,
which makes the driver that is based solely on those CRC32 instructions
redundant. So remove it.

Note that this aligns arm64 with ARM, whose accelerated CRC32 driver
also combines the CRC32 extension based and the PMULL based versions.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: NMatthias Brugger <mbrugger@suse.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This will allow the default kernel build to boot on Cavium ThunderX2
CN99XX processors.
Signed-off-by: NJayachandran C <jnair@caviumnetworks.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Enable the NAND framework and the Denali NAND controller driver.
This NAND controller is used on UniPhier SoCs.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Enable the block layer support for MTD devices.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Enable the Cadence SD/SDIO/eMMC controller.  This is used on
Socionext UniPhier SoC family.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Since much more arm64 SoCs with numa nodes, it's better to enable
NUMA and NUMA_BALANCING to improve the performance on test.

Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Signed-off-by: NZhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This commit enables the XORv2 DMA driver, which is used on the ARM64
Marvell Armada 7K and 8K platforms.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The sysfs ABI to GPIO is marked obsolete and should not be
encouraged. Users should be encouraged to switch to using the
character device.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The default value of 17 for CONFIG_LOG_BUF_SHIFT is much more suitable
than 14. The latter easily leads to lost kernel messages on systems with
only one CPU core.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds CONFIG_HIBERNATION to the arm64 defconfig.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Enable additional options necessary to boot rk3399-based boards to
boot from either emmc or usb devices, like the arasan sdhci and its phy
as well as the usb2 phy and general rockchip power-domain support.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Many rockchip based arm64 boards use RK808 as PMIC, so
enabe it here let the board bootup normally.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
[added rk808-rtc as module and rk808-clk output built in]
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

I2C and MMC are very basic modules for a board to bootup, as I2C always
used to configure PMIC and MMC devices often used to store filesytem.
So enable them here to let the rockchip based arm64 boards can bootup.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Enable Tegra186 SoC.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Given the mimimal hardware support for msm899(2/4) currently.
A few config options are needed to allow for continued
development and booting.

The following are needed for continued development and
booting:
  -8994 pinctrl for serial support
  -Enable Global Glock Controller (gcc)
Signed-off-by: NJeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

Add the thermal driver for bcm2837 to list of compiled modules
in the default config.

Changelog:
 V7 -> V8: rebased
Signed-off-by: NMartin Sperl <kernel@martin.sperl.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Enable support for on board SPI EEPROM by setting
CONFIG_EEPROM_AT25=m
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

This patch adds CONFIG_HIBERNATION to the arm64 defconfig.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Extend the ARM64 defconfig to enable the DU DRM device as module
together with required dependencies of V4L2 FCP and VSP modules.

This enables VGA output on the r8a7795 Salvator-X board.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable MMC related defaults configs for MMC, PWM and PWM clock.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Most of the drivers are included as modules, except for serial (needed
for early console), WDT (required for reboot), and the dependency
chain of RASPBERRYPI_POWER (which is currently not buildable as a
module, but should be changed).
Signed-off-by: NEric Anholt <eric@anholt.net>

Enable CONFIG_GPIO_XGENE_SB.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NQuan Nguyen <qnguyen@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables the configuration for the ZTE ZX family.
Signed-off-by: NJun Nie <jun.nie@linaro.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable common modules for power management; one is to enable
CPUFREQ_DT driver; the driver is used by many platforms by passing OPP
table from device tree.

Also enables thermal related drivers. Firstly we need enable
configuration CPU_THERMAL for CPU cooling device driver, this will bind
thermal zone with CPU cooling device; and enable 'power allocator'
thermal governor.
Signed-off-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

drivers/char/hw_random/Kconfig has 'default m', so
simply removing this entry from the defconfig will
enable building HW random drivers as modules.
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This allows use of the SDHI SD/SDIO controller present on R-Car Gen3 SoCs
and already enabled in the DT of the r8a7795/salvator-x (H3).
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables the driver for the PCIe host controller found on the
Marvell Armada 3700 ARM64 SoCs.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Enable the following items for bluetooth mouse and speaker which base
on HCIUART.

a) CONFIG_BT_HCIUART
b) CONFIG_BT_HCIUART_LL
c) CONFIG_BT_HIDP

Enable bluetooth LED support.

d) CONFIG_BT_LEDS
Signed-off-by: NGuodong Xu <guodong.xu@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Signed-off-by: NGuodong Xu <guodong.xu@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>