If NR_IRQS is less than MAX_IRQS, we end up writing past the
irq_target_cpu array in omap_wakeupgen_init():

/* Associate all the IRQs to boot CPU like GIC init does. */
for (i = 0; i < max_irqs; i++)
	irq_target_cpu[i] = boot_cpu;

This can happen if SPARSE_IRQ is enabled as by default NR_IRQS is
set to 16. Without this patch we're overwriting other data during
the boot.

Looks like a similar fix was posted by Benoit Cousson earlier
as "ARM: OMAP2+: wakeupgen: Fix wrong array size for irq_target_cpu"
but was lost.

Cc: stable@vger.kernel.org
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP4 sl2if IP block requires some special programming for it to
enter idle. Without this programming, it will prevent the rest of
the chip from entering full chip idle.

This patch comments out the IP block data.

Later, once the appropriate support is available, this patch can be
reverted.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Clock and module mode are explictly enable when hwmod is enabled. But if
the hwmod doesn't get ready on time, clocks are disabled but module is left
enabled.
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

IVA2 hwmod resets were missing the status bit offsets. Also, as the
hwmod itself didn't have prcm info at all, resetting iva hwmod was
accessing some bogus memory addresses. Added both infos to fix this.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Commit 4da71ae6 ("OMAP: clockdomain: Arch specific funcs for
clkdm_clk_enable/disable") called the OMAP2xxx-specific functions for
clockdomain wakeup and sleep.  This would probably have broken
software-supervised clockdomain wakeup and sleep on OMAP3.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Acked-by: NRajendra Nayak <rnayak@ti.com>

With commit ae6df418
Sub: ARM: OMAP2+: dmtimer: cleanup fclk usage)
The Timer functional clock naming convention has changed from
gptX_fck => timerXfck, and so as the timer init function
in mach-omap2/timer.c.
OMAP4 clocktree also has changed accordingly.

AM33xx Clock Tree has been merged during rc3-4 timeframe,
before above commit got merged, so similar change is required
for AM33xx as well (Change the gptX_fck => timerX_fck).
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Fix inconsistency between mach-types and CONFIG_ name that prevents
touchbook board from booting.
Signed-off-by: NRadek Pilar <mrkva@mrkva.eu>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently, omap2_sync32k_clocksource_init() function initializes the 32K
timer as the system clock source regardless of the CONFIG_OMAP_32K_TIMER
setting.
Fix this by providing a default implementation for
!CONFIG_OMAP_32K_TIMER case.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

The new omap4 cpuidle implementation currently requires
ARCH_NEEDS_CPU_IDLE_COUPLED, which only works on SMP.

This patch makes it possible to build a non-SMP kernel
for that platform. This is not normally desired for
end-users but can be useful for testing.

Without this patch, building rand-0y2jSKT results in:

drivers/cpuidle/coupled.c: In function 'cpuidle_coupled_poke':
drivers/cpuidle/coupled.c:317:3: error: implicit declaration of function '__smp_call_function_single' [-Werror=implicit-function-declaration]

It's not clear if this patch is the best solution for
the problem at hand. I have made sure that we can now
build the kernel in all configurations, but that does
not mean it will actually work on an OMAP44xx.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

The 4430 OPP table was being registered for all other OMAP4 variants
too, like 4460 and 4470 causing issues with cpufreq driver
enabled. 4460 and 4470 devices have different OPPs as compared to
4430, and they should be populated seperately. As long as that
happens, let the OPP table registeration happen only on 4430 device.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

OMAP4 sleep entry code even though itself don't use many CPU registers
makes call to the v7_flush_dcache_all() which uses them. Since
v7_flush_dcache_all() doesn't make use of stack, the caller must take
care of the stack frame. Otherwise it will lead to corrupted stack frame.

Fix it by saving used registers.
Reported-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This reverts commit 58f0829b.

Converstion to per-pwrdm per/post transition calls was a bit
premature.  Only tracking MPU, PER & CORE in the idle path means we
lose the accounting for all the other powerdomains which may also
transition in idle.  On OMAP3, due to autodeps, several powerdomains
transition along with MPU (e.g. DSS, USBHOST), and the accounting for
these was lost with this patch.  Since the accounting includes the
context loss counters, drivers for devices in those power domains
would never notice context lost, so would likely hang after any
off-mode transitions.

This patch should be revisited when the upcoming clkdm/pwrmdm/voltdm
use-counting seires is merged since then we can properly do accounting
without relying on a call in the idle path.

In addition, the original patch had another bug because the PER
powerdomain accounting was not updated until after the GPIO resume
hook is called.  Since gpio_resume_after_idle() checks the context
loss count (which is not yet updated) it would not properly restore
context, leaving the GPIO banks in an undefined state.

Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reported-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.

Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.

Tested on 3430/n900, OMAP3530/Overo Fire, 3730/Overo FireSTORM,
3730/Beagle-xM.
Signed-off-by: NKevin Hilman <khilman@ti.com>

remove comment for nonexistent member
Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The random config builds with PM and !ARM_CPU_SUSPEND breaks with below
error on omap2plus_defconfig.

arch/arm/mach-omap2/sleep44xx.S:323: undefined reference to `cpu_resume'
arch/arm/mach-omap2/omap-mpuss-lowpower.c:278: undefined reference to `cpu_suspend'

This is because recently merged OMAP5 platform shares the common files
with OMAP4 but doesn't select ARM_CPU_SUSPEND. Without the ARM_CPU_SUSPEND
the sleep code is meaningless.

Fix the same by adding ARM_CPU_SUSPEND for OMAP5. The suggestion came from
Russell King in an off-list discussion.

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Kevin Hilman <khilman@ti.com>
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

According to the IGEPv2 Rev.C data-sheet the LAN9221i pin 14 (IRQ) is
connected to the OMAP3730 mcspi1_cs2 pin. Since this omap mux pin acts
as an IRQ line, it has to be configured as an input GPIO.

IGEPv2 platform code sets the smsc911x_cfg->gpio_irq to GPIO 176 but
since the mux pin default mode is MODE7 (safe_mode) the driver fails
when trying to register the IRQ with the following error message:

[    1.994598] smsc911x: Driver version 2008-10-21
[    3.704162] irq 272: nobody cared (try booting with the "irqpoll" option)
[    3.711364] [<c001a114>] (unwind_backtrace+0x0/0xf0) from [<c009a0d4>] (__report_bad_irq+0x20/0xbc)
[    3.720916] [<c009a0d4>] (__report_bad_irq+0x20/0xbc) from [<c009a41c>] (note_interrupt+0x1d8/0x238)
[    3.730560] [<c009a41c>] (note_interrupt+0x1d8/0x238) from [<c0098234>] (handle_irq_event_percpu+0xc0/0x260)
[    3.740936] [<c0098234>] (handle_irq_event_percpu+0xc0/0x260) from [<c0098410>] (handle_irq_event+0x3c/0x5c)
[    3.751312] [<c0098410>] (handle_irq_event+0x3c/0x5c) from [<c009abe0>] (handle_level_irq+0xac/0x10c)
[    3.761047] [<c009abe0>] (handle_level_irq+0xac/0x10c) from [<c0097a34>] (generic_handle_irq+0x30/0x48)
[    3.770935] [<c0097a34>] (generic_handle_irq+0x30/0x48) from [<c02a6b74>] (gpio_irq_handler+0x180/0x1d4)
[    3.780944] [<c02a6b74>] (gpio_irq_handler+0x180/0x1d4) from [<c0097a34>] (generic_handle_irq+0x30/0x48)
[    3.790954] [<c0097a34>] (generic_handle_irq+0x30/0x48) from [<c0013e18>] (handle_IRQ+0x4c/0xac)
[    3.800231] [<c0013e18>] (handle_IRQ+0x4c/0xac) from [<c000858c>] (omap3_intc_handle_irq+0x60/0x74)
[    3.809783] [<c000858c>] (omap3_intc_handle_irq+0x60/0x74) from [<c04979e4>] (__irq_svc+0x44/0x60)
[    3.819213] Exception stack(0xee42fde0 to 0xee42fe28)
[    3.824554] fde0: 00000001 00000001 00000000 00000000 60000013 c06cce14 c06cce14 00000110
[    3.833190] fe00: 00000000 c06ccdf4 60000013 ee41d000 fb058064 ee42fe28 c0089e08 c04976b4
[    3.841796] fe20: 20000013 ffffffff
[    3.845489] [<c04979e4>] (__irq_svc+0x44/0x60) from [<c04976b4>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[    3.855499] [<c04976b4>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c0099744>] (__setup_irq+0x1b8/0x3f0)
[    3.865875] [<c0099744>] (__setup_irq+0x1b8/0x3f0) from [<c0099a34>] (request_threaded_irq+0xb8/0x140)
[    3.875701] [<c0099a34>] (request_threaded_irq+0xb8/0x140) from [<c0487950>] (smsc911x_drv_probe+0x75c/0x11a4)
[    3.886260] [<c0487950>] (smsc911x_drv_probe+0x75c/0x11a4) from [<c02e9bcc>] (platform_drv_probe+0x18/0x1c)
[    3.906707] [<c02e89b8>] (driver_probe_device+0x90/0x210) from [<c02e8bcc>] (__driver_attach+0x94/0x98)
[    3.916625] [<c02e8bcc>] (__driver_attach+0x94/0x98) from [<c02e7298>] (bus_for_each_dev+0x50/0x7c)
[    3.926177] [<c02e7298>] (bus_for_each_dev+0x50/0x7c) from [<c02e81d4>] (bus_add_driver+0x184/0x248)
[    3.935821] [<c02e81d4>] (bus_add_driver+0x184/0x248) from [<c02e909c>] (driver_register+0x78/0x12c)
[    3.945465] [<c02e909c>] (driver_register+0x78/0x12c) from [<c0008648>] (do_one_initcall+0x34/0x178)
[    3.955108] [<c0008648>] (do_one_initcall+0x34/0x178) from [<c066e8f4>] (kernel_init+0xfc/0x1c0)
[    3.964385] [<c066e8f4>] (kernel_init+0xfc/0x1c0) from [<c00140b0>] (kernel_thread_exit+0x0/0x8)
[    3.973632] handlers:
[    3.976043] [<c034e2cc>] smsc911x_irqhandler
[    3.980560] Disabling IRQ #272
Signed-off-by: NJavier Martinez Canillas <javier@dowhile0.org>
Acked-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

1) The above commit introduced a common ->get_pendown_state() function
into the generic code, but that function was board-specific for the
OMAP3EVM and thus broke most other boards using this code.

2) The above commit was mis-merged introducing another bug which
prevents the ads7846 driver probe function to succeed.
The omap_ads7846_init() function frees the pendown GPIO in case there is
no ->get_pendown_state() function set by the caller (board specific
code), so it can be requested later by the ads7846 driver.
The above commit add a common ->get_pendown_state() function without
removing the gpio_free() call and thus once the ads7846 driver tries
to use the pendown GPIO, it crashes as the pendown GPIO has not been
requested.

3) The above commit introduces NO new functionality as
get_pendown_state() function is already implemented in a suitable way by
the ads7846 driver and the debounce time handling has already been
fixed by commit 97ee9f01 (ARM: OMAP: fix the ads7846 init code).

This reverts commit 16aced80.

Conflicts:
	arch/arm/mach-omap2/common-board-devices.c

Solved by taking the working version prior to the above commit.

Cc: Zumeng Chen <zumeng.chen@windriver.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

DMAengine uses the DMA engine device structure when mapping/unmapping
memory for DMA, so the MMC devices do not need their DMA masks
initialized (this reflects hardware: the MMC device is not the device
doing DMA.)
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

OMAP4 idle driver uses CLOCK_EVT_NOTIFY_BROADCAST_[ENTER/EXIT]
for broadcast clock events. But _ENTER/_EXIT doesn't really open
broadcast clock events and to explicitly setup the broadcast device,
CLOCK_EVT_NOTIFY_BROADCAST_ON should be used.

Add the missing CLOCK_EVT_NOTIFY_BROADCAST_ON clockevent notifications.
This will setup the broadcast timer in either periodic/oneshot modes
correctly. Recent clockevent infrastructure change 77b0d60c {leave the
broadcast device in shutdown mode when not needed} exposed this bug
leading to boot hangs in oneshot mode. Prior to this, periodic broadcast
mode was also broken. This change fixes both the periodic/oneshot broadcast
modes.

Discussion thread :
	https://lkml.org/lkml/2012/4/9/13Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

With coupled idle states, a failure for any CPU to hit a low power
state must be coordinated such that all CPUs abort.

On OMAP4, when entering a coupled state, CPU0 has to wait for CPU1 to
enter its low power state before it can enter its low power state.

This is implemented by letting CPU0 wait for the CPU1 powerdomain to
hit off.  However, there are conditions where CPU1 might abort/fail
and not hit off while CPU0 is waiting for it.  For example, a CPU1
wakeup or a failed attempt to hit off due to hardware conditions.

To avoid the deadlock where CPU0 would continually wait for CPU1 to
hit off-mode, this patch adds a flag to signal when each CPU has come
out of its low-power state.  CPU0 then checks whether CPU1 has hit off
*or* has already completed its attempt to hit off.  If the latter,
CPU0 must abort its attempt to hit a low-power state so the coupled
state enter method can return.

In addition, cpuidle_coupled_parallel_barrier() is used to ensure the
clearing of the 'done' flag is synchronized on all CPUs.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

OMAP4 CPUDILE driver is converted mainly based on notes from the
coupled cpuidle patch series.

The changes include :
- Register both CPUs and C-states to cpuidle driver.
- Set struct cpuidle_device.coupled_cpus
- Set struct cpuidle_device.safe_state to non coupled state.
- Set CPUIDLE_FLAG_COUPLED in struct cpuidle_state.flags for each
  state that affects multiple cpus.
- Separate ->enter hooks for coupled & simple idle.
- CPU0 wait loop for CPU1 power transition.
- CPU1 wakeup mechanism for the idle exit.
- Enabling ARCH_NEEDS_CPU_IDLE_COUPLED for OMAP4.

Thanks to Kevin Hilman and Colin Cross on the suggestions/fixes
on the intermediate version of this patch.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

For coupled cpuidle to work when both cpus are active, it needs a global timer
that can handle events for both cpus.  This timer is used as the broadcast
clock-event when the per-cpu timer hardware stop in low power states.
Set the cpumask of clockevent_gpt to all cpus, set the rating correctly, and
set the irq to allow the clockevent core to determine the affinity of the
timer.
Signed-off-by: NColin Cross <ccross@android.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Correcting spelling typo in mach-omap2
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit cb8ca589 (ARM: omap3evm: enable VBUS switch for EHCI tranceiver)
added a new randconfig error if TWL4030_CORE is not selected:

arch/arm/mach-omap2/board-omap3evm.c:368: undefined reference to `twl_i2c_read_u8'
arch/arm/mach-omap2/board-omap3evm.c:370: undefined reference to `twl_i2c_write_u8'
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Adding the build support required for OMAP5 soc
in to omap2+ config.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Adding the minimal support for OMAP5 evm board
with device tree.
Reviewed-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Move the irq_match arrays and the irq init functions of OMAP 2,3
and 4 based boards out of board-generic.c file and also rename the
irq init function to match the interrupt controller present in
the SOCs.

This is a preparatory patch to add the OMAP5 evm board's irq init
support with device tree.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Add OMAP5 SMP boot support using OMAP4 SMP code. The relevant code paths
are runtime checked using cpu id
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

OMAP4 and OMAP5 share same WakeupGen IP with below few udpates on OMAP5.
- Additional 32 interrupt support is added w.r.t OMAP4 design.
- The AUX CORE boot registers are now made accessible from non-secure SW.
- SAR offset are changed and PTMSYNC* registers are removed from SAR.

Patch updates the WakeupGen code accordingly.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The l3 interconnect ip is same for OMAP4 and OMAP5.
So reuse the l3 error handler error code for OMAP5
as well. Also a few targets has been newly added for
OMAP5. So updating the driver for that here.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

GPMC module is the same as in OMAP4.
Just update the base address and irq number.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Adding the Initialisaton for clocksource and clockevent device
on OMAP5 Socs.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP
architecture. It's a dual core SOC with GIC used for interrupt
handling and with an integrated L2 cache controller.

OMAP5432 is another variant of OMAP5430, with a
memory controller supporting DDR3 and SATA.

Patch includes:
 - The machine specific headers and sources updates.
 - Platform header updates.
 - Minimum initialisation support for serial.
 - IO table init
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Adding the OMAP5 ES1.0, 2.0 and OMAP5432 cpu revision
detection support.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If provided dt support, then skip add wdt platform device as usual.
Signed-off-by: NXiao Jiang <jgq516@gmail.com>
Reviewed-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently most ads7846 config definitions for OMAP3 series boards have
been moved to common-board-devices.c, and it is transparent for init.
And it's no very proper to do gpio_request based on get_pendown_state
since omap_ads7846_init knows everything about ads7846_config.

So it's more fit to request gpio according to the right gpio_pendown
and set debounce time conditionally. If we don't set proper debouce
time, there are flooded interrupt counters of ads7846 responding to
one time touch on screen, then the driver couldn't work very well.

This patch has been validated on 3530evm.
Signed-off-by: NZumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This was chosen by following the trace on the schematic from component U131
and U134 to the CPEN pin on the USB3320 device.

TWL4030.GPIO2-...->(T2_GPIO2_3V3)U131-..>nUSB2_EN-..>U134-..>EXP_nUSB2_1V8
which starts EHCI tranceiver USB3320.

This will set TWL4030.GPIO2 as output pin to drive EHCI tranceiver.
Signed-off-by: NZumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>