Some chips such as 88E6352 and 88E6390 can be programmed to add delays
to RXCLK for IND inputs or to GTXCLK for OUTD outputs when port is in
RGMII mode.

Add a port function to program such delays according to the provided PHY
interface mode.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similarly to port's link, add setter to force port's half duplex, full
duplex or let normal duplex detection occurs.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the chips will have a port register control bits to force the
port's link up, down, or let normal link detection occurs.

Implement such operation to use it later when setting duplex, etc.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add port functions to set the port 802.1Q mode.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add port functions to access the ports default VID.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add functions to port files to access the ports default FID.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a port function to access the Port Based VLAN Map register.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the port STP state setter to the port files.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell switches contains one internal SMI device per port, called
"Port Registers". Depending on the model, the addresses of these devices
start from 0x0, 0x8 or 0x10.

Start moving Port Registers specific code to their own files.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system-status register is actually 16-bit wide and not 8 bit-wide.

Fixes: 233fa44b ("mlxsw: pci: Implement reset done check")
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Synopsys Designware MAC Glue layer for the Oxford Semiconductor OX820.
Acked-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver sets the skb l4/l3 hash based on NIC_CFG_RSS_HASH_TYPE_*,
which is bit mask. This is wrong. Hw actually provides us enum.
Use CQ_ENET_RQ_DESC_RSS_TYPE_* to set l3 and l4 hash type.

Fixes: bf751ba8 ("driver/net: enic: record q_number and rss_hash for skb")
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Reviewed-by: NDavid Dillow <dave@thedillows.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To utilize phylib with interrupt fully than handling some of phy stuff in the MAC driver,
create irq_domain for USB interrupt EP of phy interrupt and
pass the irq number to phy_connect_direct() instead of PHY_IGNORE_INTERRUPT.

Idea comes from drivers/gpio/gpio-dl2.c
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The old ethtool api (get_setting and set_setting) has generic mii
functions mii_ethtool_sset and mii_ethtool_gset.

To support the new ethtool api ({get|set}_link_ksettings), we add
two generics mii function mii_ethtool_{get|set}_link_ksettings_get.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

XDP statistics are reported in ethtool, in total and per ring,
as follows:
- xdp_drop: the number of packets dropped by xdp.
- xdp_tx: the number of packets forwarded by xdp.
- xdp_tx_full: the number of times an xdp forward failed
	due to a full tx xdp ring.

In addition, all packets that are dropped/forwarded by XDP
are no longer accounted in rx_packets/rx_bytes of the ring,
so that they count traffic that is passed to the stack.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separately manage the two types of TX rings: regular ones, and XDP.
Upon an XDP set, do not borrow regular TX rings and convert them
into XDP ones, but allocate new ones, unless we hit the max number
of rings.
Which means that in systems with smaller #cores we will not consume
the current TX rings for XDP, while we are still in the num TX limit.

XDP TX rings counters are not shown in ethtool statistics.
Instead, XDP counters will be added to the respective RX rings
in a downstream patch.

This has no performance implications.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support XDP CQ type, and refactor the CQ type enum.
Rename the is_tx field to match the change.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable support for IPv4 multicast:
- similar to unicast the flow struct is updated to L3 master device
  if relevant prior to calling fib_rules_lookup. The table id is saved
  to the lookup arg so the rule action for ipmr can return the table
  associated with the device.

- ip_mr_forward needs to check for master device mismatch as well
  since the skb->dev is set to it

- allow multicast address on VRF device for Rx by checking for the
  daddr in the VRF device as well as the original ingress device

- on Tx need to drop to __mkroute_output when FIB lookup fails for
  multicast destination address.

- if CONFIG_IP_MROUTE_MULTIPLE_TABLES is enabled VRF driver creates
  IPMR FIB rules on first device create similar to FIB rules. In
  addition the VRF driver does not divert IPv4 multicast packets:
  it breaks on Tx since the fib lookup fails on the mcast address.

With this patch, ipmr forwarding and local rx/tx work.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to always allocate the same number of TX and RX rings
so the support for having r_vectors without one of the rings
was dropped.  That makes us, however, unnecessarily limited
to 8 TX rings (8 is the Linux RSS default) most of the time.
Also we are about to add channel count configuration via
ethtool, so bring that support back.  TX rings can now default
to num_online_cpus() and RX rings to netif_get_num_default_rss_queues().
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

num_irqs is not used anywhere, replace it with max_r_vecs which holds
number of allocated RX/TX vectors and is going to be useful soon.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nfp_net_irqs_wanted() doesn't really encapsulate much logic,
remove it and inline the calculations.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use unsigned int consistently for vector/ring counts.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are currently using define for max TX rings to allocate IRQ
vectors.  It's OK since the max number of rings for TX and RX
are currently the same, but lets make the code nicer by taking
max of the two.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already force ring sizes to be power of 2 so replace
modulo operations with AND (size - 1) in index calculations.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a separate buffer allocation function to be called
from NAPI.  We can make assumptions about the context and
buffer size.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Speed up RX processing by moving to the alloc_frag()/build_skb()
paradigm.  Since we're no longer mapping the entire buffer for
DMA add helpers which take care of calculating offsets and
lengths.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nfp_net_rx() is quite long already and about to get longer.
Move buffer drop/recycle to a helper.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper function to calculate the buffer size at run time.
Buffer lengths will now depend on the FW prepend configuration
instead of assuming the most space consuming configuration and
defaulting to 2k buffers at initialization time.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't declare functions as static inline in .c files and
remove dead code it was hiding.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ether_setup() will be invoked by alloc_etherdev_mqs(), no need
to call it again.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop all code related to nfp3200.  It was never widely deployed
as a NIC.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are few variables in nfp_net_poll() which are used only
once or unused but set.  Remove them.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When relaxing the limitation on the number of unicast MAC filters
an interface can configure, qed started passing the MAC quota to
qede. However, the value is initialized only for PFs, causing VFs
to always try and configure themselves as promiscuous
[as they believe they lack the resources to configure the rx-mode].

Fixes: 7b7e70f9 ("qed*: Allow unicast filtering")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver is now setting the ndev's priv_flags instead of adding to it,
causing pktgen failure to utilize various features due to the loss
of the IFF_TX_SKB_SHARING indication.

Fixes: 7b7e70f9 ("qed*: Allow unicast filtering")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Makefile/Kconfig currently controlling compilation of this code is:

drivers/net/cris/Makefile:obj-$(CONFIG_ETRAX_ARCH_V10) += eth_v10.o

arch/cris/Kconfig:config ETRAX_ARCH_V10
arch/cris/Kconfig:       bool

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

There was a one line wrapper for the int init function, which made no
sense; hence we just put the device_initcall on the true init function
itself and delete the pointless wrapper.  In doing that we get rid of
the following compile warning:

   WARNING: drivers/net/built-in.o(.text+0x1e28): Section mismatch in
   reference from the function etrax_init_module() to the function
   .init.text:etrax_ethernet_init()

We don't replace module.h with init.h since the file already has that.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: netdev@vger.kernel.org
Cc: linux-cris-kernel@axis.com
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed some of unnecessary if statements and unreachable code found by
static code analysis tool.
The return value of i40e_vsi_control_rings(..., false) is always 0. So,
test for non-zero will never be true. The function has been split into
"int i40e_vsi_start_rings()" and "void i40e_vsi_stop_rings()" for better
understanding.
Similarly, the function i40e_vsi_kill_vlan() never fails. So, checking
for return value is also unnecessary. Function definition changed to void.
The i40e_loopback_test() function is not implemented. The function and
all references to loopback testing were removed.

Change-ID: Id45cf66f6689ce2bc4e887de13f073e30e8431bd
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds I40E_NVMUPD_STATE_ERROR state for NVM update.
Without this patch driver has no possibility to return NVM image write
failure.This state is being set when ARQ rises error.
arq_last_status is also updated every time when ARQ event comes,
not only on error cases.

Change-ID: I67ce43ba22a240773c2821b436e96054db0b7c81
Signed-off-by: NMaciej Sosin <maciej.sosin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>