The new headers contain the following changes:
(1) Added IO Unit Page 7.
(2) Added new device ids for SAS2208.
(3) Added SAS IO Unit Page 5.
(4) Added partial and slumber power management capable flags to SAS Device
    Page 0 Flags field.
(5) Added PhyInfo defines for power condition.
(6) Added Ethernet configuration pages.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NEric Moore <Eric.moore@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added device ids range for { 0x80 - 87 } , modified mpi/mpi2_cnfg.h containing
MPI2_MFGPAGE_DEVID_SAS2208_X.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NEric Moore <Eric.moore@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add support in the driver to check for valid response info in the scsi
state, then check to see if the response code is
MPI2_SCSITASKMGMT_RSP_INVALID_FRAME; when this condition occurrs, the driver
will return DID_SOFT_ERROR.  A return code of DID_SOFT_ERROR will result in
a retry at the scsi-mid layer level.  An additional change added to obtain
the response code from the 1st byte of the response info instead of last.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NEric Moore <Eric.moore@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This handles the case where driver receives a expander removal event while
it is in the middle of processing an expander add event. The existing
implementation will stop processing futher device adds when a expander
delete arrives on top of add expander add. Due to a sanity check in the
driver, the devices there were not added, were never handshaked to firmware
with the device removal handshake protocal. Since the driver didnt' do the
handshake, the controller never provide further add events.  To fix this
issue, the sanity check was removed so the driver will always do the device
removal handshake protocal.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NEric Moore <Eric.moore@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The device driver was not handling updating device handles in all cases
across diag resets. To fix this issue, the driver is converted to using sas
address instead of handle as a lookup reference to the parent expander or
sas_host. Also, for both expanders and sas host, the phy handle will be one
unique handle. In the sas host case, the phy handle can be different for
every phy, so the change is to set the handle to the handle of the first
phy; every phy will be one single sas address(phy 0) instead of a different
sas address for every phy(previous implementation). So making one consistent
sas address for all the direct attachedports to the sas host, will make it
better user experience when using udev /dev/disk/by-path dev nodes
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NEric Moore <Eric.moore@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

I've not touched the other stuff here but the word "locking" comes to mind.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I have an HP HDX 18 laptop, and noted that the configuration of the
accelerometer needs to be x_inverted.
Signed-off-by: NIan E. Morgan <penguin.wrangler@gmail.com>
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Correct orientation for  HP EliteBook 8530w.
Reported-by: NJörgen Jonssson <jorgen.jonsson@saitek.se>
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I have learned that the 6730b and 6730s have different accelerometer
orientation, and have modified the driver accordingly (diff attached),
while dropping the wild guess for AMD based 6735 having the same
orientation as Intel based 6730 (this is not true for any other related
series/family, thus is not probable for 673x).
Signed-off-by: NPavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the case where cpuidle_idle_call() returns before changing state due to
a need_resched(), it was returning with IRQs disabled.

The idle path assumes that the platform specific idle code returns with
interrupts enabled (although this too is undocumented AFAICT) and on ARM
we have a WARN_ON(!(irqs_disabled()) when returning from the idle loop, so
the user-visible effects were only a warning since interrupts were
eventually re-enabled later.

On x86, this same problem exists, but there is no WARN_ON() to detect it.
As on ARM, the interrupts are eventually re-enabled, so I'm not sure of
any actual bugs triggered by this.  It's primarily a
correctness/consistency fix.

This patch ensures IRQs are (re)enabled before returning.
Reported-by: NHemanth V <hemanthv@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Cc: <stable@kernel.org>		[2.6.31.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow csrows to properly initialize when the topology only has active
channels on 2 and 3.  This new check allows proper detection and
initialization in this topology.  Only checking the first mrt that
represented channels 0 and 1 is not sufficient.

I also fixed up the related debug information path.  I can submit as a 2nd
patch if needed.
Signed-off-by: NKeith Mannthey <kmannth@us.ibm.com>
Acked-by: NAristeu Rozanski <aris@ruivo.org>
Signed-off-by: NDoug Thompson <dougthompson@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When building without CONFIG_PCI the edac_pci_idx variable is unused,
causing a build-time warning.  Wrap the variable in #ifdef CONFIG_PCI,
just like the rest of the PCI support.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NDoug Thompson <dougthompson@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The i5400 EDAC driver has several bugs with chip-select row computation
which most likely lead to bugs in detailed error reporting.  Attempts to
contact the authors have gone mostly unanswered so I am presenting my diff
here.  I do not subscribe to lkml and would appreciate being kept in the
cc.

The most egregious problem was miscalculating the addresses of MTR
registers after register 0 by assuming they are 32bit rather than 16.
This caused the driver to miss half of the memories.  Most motherboards
tend to have only 8 dimm slots and not 16, so this may not have been
noticed before.

Further, the row calculations multiplied the number of dimms several
times, ultimately ending up with a maximum row of 32.  The chipset only
supports 4 dimms in each of 4 channels, so csrow could not be higher than
4 unless you use a row per-rank with dual-rank dimms.  I opted to
eliminate this behavior as it is confusing to the user and the error
reporting works by slot and not rank.  This gives a much clearer view of
memory by slot and channel in /sys.
Signed-off-by: NJeff Roberson <jroberson@jroberson.net>
Signed-off-by: NDoug Thompson <dougthompson@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The gpio_twl4030_probe() function calls gpio_twl4030_remove(), and the
former has __devinit, so the latter cannot use __devexit.  Otherwise we
hit the section mismatch warning:

WARNING: drivers/gpio/built-in.o(.devinit.text+0x71a): Section mismatch
	in reference from the function _gpio_twl4030_probe() to the function
	.devexit.text:_gpio_twl4030_remove()
The function __devinit _gpio_twl4030_probe() references a function
	__devexit _gpio_twl4030_remove().
This is often seen when error handling in the init function uses
	functionality in the exit path.
The fix is often to remove the __devexit annotation of
	_gpio_twl4030_remove() so it may be used outside an exit section.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The IBM Saturn serial card has only one port. Without that fixup,
the kernel thinks it has two, which confuses userland setup and
admin tools as well.

[akpm@linux-foundation.org: fix pci-ids.h layout]
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NAlan Cox <alan@linux.intel.com>
Cc: Michael Reed <mreed10@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for ADDI-DATA GmbH PCI-Express communication cards:

APCIe-7300
APCIe-7420
APCIe-7500
APCIe-7800

Warning: 8250_pci.c depends on pci_ids.h. 8250_pci.c
Signed-off-by: NKrauth Julien <Krauth.Julien@addi-data.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

is_power_of_2() appears not to be constant enough for BUILD_BUG_ON()
after the latest rework, so replace it with an open-coded test.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit bb214884 ("[PATCH] switch loop")
started to pass NULL bdev to ioctl hook.

Steps to reproduce:

	[boot with loop.max_part=1]
	[mount -o loop something so mount fails]

BUG: unable to handle kernel NULL pointer dereference at 00000000000000b8
IP: [<ffffffff811486ee>] blkdev_ioctl+0x2e/0xa30
PGD 0
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:35/ACPI0003:00/power_supply/ACAD/online
CPU 0
Modules linked in: zfs nvidia(P) [last unloaded: zfs]
Pid: 15177, comm: mount Tainted: P           2.6.32-rc4-zfs #2 Satellite X200
RIP: 0010:[<ffffffff811486ee>]  [<ffffffff811486ee>] blkdev_ioctl+0x2e/0xa30
RSP: 0018:ffff88003b3d5bb8  EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 000000000000125f RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88003b3d5ce8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 00007ffffffff000
R13: 0000000000000000 R14: ffff880071cef280 R15: 00000000000200da
FS:  00007fd77cfe7740(0000) GS:ffff880001600000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00000000000000b8 CR3: 0000000001001000 CR4: 00000000000026f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process mount (pid: 15177, threadinfo ffff88003b3d4000, task ffff88007572f920)
Stack:
 ffff88003b3d5c38 ffffffff812f95f5 ffff88007eeb6600 0000000000000000
<0> 0000000000000000 ffff88003b3d5c18 ffffffff811547d9 ffff88001bf11ef0
<0> 7fffffffffffffff ffff88001bf11ee8 ffff88001bf11ef0 0000000000000000
Call Trace:
 [<ffffffff812f95f5>] ? schedule_timeout+0x1f5/0x250
 [<ffffffff811547d9>] ? rb_insert_color+0x109/0x140
 [<ffffffff812fb754>] ? _spin_unlock_irq+0x14/0x40
 [<ffffffff812f84c6>] ? wait_for_common+0x66/0x170
 [<ffffffff8105a280>] ? default_wake_function+0x0/0x10
 [<ffffffff810f8258>] ioctl_by_bdev+0x38/0x50
 [<ffffffff811d2481>] loop_clr_fd+0x1e1/0x210
 [<ffffffff811d2522>] lo_release+0x72/0x80
 [<ffffffff810f934c>] __blkdev_put+0x1ac/0x1d0
 [<ffffffff810f937b>] blkdev_put+0xb/0x10
 [<ffffffff810f93b9>] blkdev_close+0x39/0x60
 [<ffffffff810ccef3>] __fput+0xd3/0x230
 [<ffffffff810cd06d>] fput+0x1d/0x30
 [<ffffffff810c9680>] filp_close+0x50/0x80
 [<ffffffff81061f11>] put_files_struct+0x81/0x100
 [<ffffffff81061fde>] exit_files+0x4e/0x60
 [<ffffffff81063ec5>] do_exit+0x6b5/0x730
 [<ffffffff8107b279>] ? up_read+0x9/0x10
 [<ffffffff8104c86e>] ? do_page_fault+0x18e/0x2a0
 [<ffffffff81063f81>] do_group_exit+0x41/0xc0
 [<ffffffff81064012>] sys_exit_group+0x12/0x20
 [<ffffffff81030deb>] system_call_fastpath+0x16/0x1b
Code: f8 48 89 e5 48 81 ec 30 01 00 00 48 89 5d d8 4c 89 6d e8 4c 89 65 e0 4c 89 75 f0 4c 89 7d f8 48 89 bd e8 fe ff ff 49 89 cd 89 f3 <49> 8b 88 b8 00 00 00 81 fa 68 12 00 00 0f 84 57 05 00 00 0f 86
RIP  [<ffffffff811486ee>] blkdev_ioctl+0x2e/0xa30
 RSP <ffff88003b3d5bb8>
CR2: 00000000000000b8
---[ end trace c0b4d3c3118d1427 ]---
Fixing recursive fault but reboot is needed!
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The missing probe handler hook will never probe the driver. Add it back.
Fixes broken MMC on OMAP.

We use platform_driver_probe() API since omap_hsmmc is not a hot-pluggable
device.
Signed-off-by: NRoger Quadros <ext-roger.quadros@nokia.com>
Tested-by: NFelipe Contreras <felipe.contreras@gmail.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.

Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2

- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
  are corrupted, there are twiddled single bits 1->0 and some full 32-bit
  words corrupted, sometimes commands fail (which switches /dev/hda to
  PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
  corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.

This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Tested-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I found that the current version of drivers/net/usb/dm9601.c can be used to
successfully drive a low-power, low-cost network adapter with USB ID
0a46:9000, based on a DM9000E chipset. As no device with this ID is yet
present in the kernel, I have created a patch that adds support for the device
to the dm9601 driver.

Created and tested against linux-2.6.32-rc5.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mailbox command process would only process a maximum of 5 unrelated
firmware events while waiting for it's command completion status.
It should process an unlimited number of events while waiting for a maximum of 5 seconds.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up driver resources without touch the hardware. Add pci
save/restore state.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In mii monitor mode, bond_check_dev_link() calls the the ioctl
handler of slave devices. It stores the ndo_do_ioctl function
pointer to a static (!) ioctl variable and later uses it to call the
handler with the IOCTL macro.

If another thread executes bond_check_dev_link() at the same time
(even with a different bond, which none of the locks prevent), a
race condition occurs. If the two racing slaves have different
drivers, this may result in one driver's ioctl handler being
called with a pointer to a net_device controlled with a different
driver, resulting in unpredictable breakage.

Unless I am overlooking something, the "static" must be a
copy'n'paste error (?).
Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On SMP guests, reads from the ring might bypass used index reads. This
causes guest crashes because host writes to used index to signal ring
data readiness.  Fix this by inserting rmb before used ring reads.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org

Commit f68d2408
in 2.6.32-rc1 broke requesting IRQs for per-VQ MSI-X vectors:
- vector number was used instead of the vector itself
- we try to request an IRQ for VQ which does not
  have a callback handler

This is a regression that causes warnings in kernel log,
potentially lower performance as we need to scan vq list,
and might cause system failure if the interrupt
requested is in fact needed by another system.

This was not noticed earlier because in most cases
we were falling back on shared interrupt for all vqs.

The warnings often look like this:

virtio-pci 0000:00:03.0: irq 26 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 27 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 28 for MSI/MSI-X
IRQ handler type mismatch for IRQ 1
current handler: i8042
Pid: 2400, comm: modprobe Tainted: G        W
2.6.32-rc3-11952-gf3ed8d8-dirty #1
Call Trace:
 [<ffffffff81072aed>] ? __setup_irq+0x299/0x304
 [<ffffffff81072ff3>] ? request_threaded_irq+0x144/0x1c1
 [<ffffffff813455af>] ? vring_interrupt+0x0/0x30
 [<ffffffff81346598>] ? vp_try_to_find_vqs+0x583/0x5c7
 [<ffffffffa0015188>] ? skb_recv_done+0x0/0x34 [virtio_net]
 [<ffffffff81346609>] ? vp_find_vqs+0x2d/0x83
 [<ffffffff81345d00>] ? vp_get+0x3c/0x4e
 [<ffffffffa0016373>] ? virtnet_probe+0x2f1/0x428 [virtio_net]
 [<ffffffffa0015188>] ? skb_recv_done+0x0/0x34 [virtio_net]
 [<ffffffffa00150d8>] ? skb_xmit_done+0x0/0x39 [virtio_net]
 [<ffffffff8110ab92>] ? sysfs_do_create_link+0xcb/0x116
 [<ffffffff81345cc2>] ? vp_get_status+0x14/0x16
 [<ffffffff81345464>] ? virtio_dev_probe+0xa9/0xc8
 [<ffffffff8122b11c>] ? driver_probe_device+0x8d/0x128
 [<ffffffff8122b206>] ? __driver_attach+0x4f/0x6f
 [<ffffffff8122b1b7>] ? __driver_attach+0x0/0x6f
 [<ffffffff8122a9f9>] ? bus_for_each_dev+0x43/0x74
 [<ffffffff8122a374>] ? bus_add_driver+0xea/0x22d
 [<ffffffff8122b4a3>] ? driver_register+0xa7/0x111
 [<ffffffffa001a000>] ? init+0x0/0xc [virtio_net]
 [<ffffffff81009051>] ? do_one_initcall+0x50/0x148
 [<ffffffff8106e117>] ? sys_init_module+0xc5/0x21a
 [<ffffffff8100af02>] ? system_call_fastpath+0x16/0x1b
virtio-pci 0000:00:03.0: irq 26 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 27 for MSI/MSI-X
Reported-by: NMarcelo Tosatti <mtosatti@redhat.com>
Reported-by: NShirley Ma <xma@us.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

virtio net used to unlink skbs from send queues on error,
but ever since 48925e37
we do not do this. This causes guest data corruption and crashes
with vhost since net core can requeue the skb or free it without
it being taken off the list.

This patch fixes this by queueing the skb after successful
transmit.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Page buffers containing packets with an incorrect checksum or using a
protocol not handled by hardware checksum offload were previously not
passed to LRO.  The conversion to GRO changed this, but did not set
the ip_summed value accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BNX2_L2CTX_STATUSB_NUM definition needs to be changed to match
the recent firmware update:

commit 078b0735
bnx2: Update firmware to 5.0.0.j3.

Without the fix, bnx2 can crash intermittently in bnx2_rx_int() when
iSCSI is enabled.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This sets the fbcon to use TRUECOLOR by default, it then
only modifies the pseudo palette for fbcon, and only touches
the real palette when in 8-bit pseudo color mode.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Sometimes we will get the incorrect display modeline when parsing the detailed
timing in EDID. For example:
   >hsync/vsync width is zero
   >sync is beyond the blank.

So add the basic check for the detailed timing in EDID to avoid the incorrect
display modeline.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Since we register all radeon devices, and the arbiter only cares about
VGA class ones, we will fail to startup on display controller class devices.
We don't gain anything by using the return value here.

this helps kms on sparc64 get started.
Reported-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Test whether index is within bounds before reading the element
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the following sparse warnings:

$ make modules SUBDIRS=drivers/net/wireless/libertas C=1 CF=-D__CHECK_ENDIAN__
make: Entering directory `/usr/src/linux-wl'
  CHECK   drivers/net/wireless/libertas/if_spi.c
drivers/net/wireless/libertas/if_spi.c:137:16: warning: incorrect type in initializer (different base types)
drivers/net/wireless/libertas/if_spi.c:137:16:    expected unsigned short [unsigned] [usertype] reg_out
drivers/net/wireless/libertas/if_spi.c:137:16:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:191:16: warning: incorrect type in initializer (different base types)
drivers/net/wireless/libertas/if_spi.c:191:16:    expected unsigned short [unsigned] [usertype] reg_out
drivers/net/wireless/libertas/if_spi.c:191:16:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:256:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:256:24:    expected restricted __le32 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:256:24:    got unsigned int *<noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'struct b43_wl' declaration is missing at 'leds.h'.
It should be declared to avoid getting some GCC warnings at 'b43_leds_unregister'.
Signed-off-by: NMiguel Botón <mboton@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"b43: Fix PPC crash in rfkill polling on unload" fixed the bug reported
in Bugzilla No. 14181; however, it introduced a new bug. Whenever the
radio switch was turned off, it was necessary to unload and reload
the driver for it to recognize the switch again.

This patch fixes both the original bug in #14181 and the bug introduced by
the previous patch. It must be stated, however, that if there is a BCM4306/3
with an rfkill switch (not yet proven), then the driver will need an
unload/reload cycle to turn the device back on.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBenoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 308cf8e1.  This
patch had trouble with transparent bridges, among other things.  A more
readable and correct version should land in 2.6.33.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add include asm/cacheflush.h,  because declaration of __flush_purge_region
moved to asm/cacheflush.h.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>