This is required per SBP-2 clause 5.2.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

noticed by Jay Fenlason
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Replace a cast with a container_of().  As long as nobody reorders the
structure elements, they do the same thing, but container_of() is more
readable.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added complete_command_orb)
Acked-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This affects of course only the "soft shutdown" case, e.g. "modprobe -r
firewire-sbp2", while it doesn't matter for hot unplug.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This currently only affects one bridge in the hardwired blacklist.
I don't own one of those, hence haven't tested it.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

cleanup after "firewire: support S100B...S400B and link slower than PHY"
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Use a speed probe to determine the speed over 1394b buses and of nodes
which report a link speed less than their PHY speed.

Log the effective maximum speed of newly created nodes in dmesg.

Also, read the config ROM (except bus info block) at the maximum speed
rather than S100.  This isn't a real optimization though because we
still only use quadlet read requests for the entire ROM.

The patch also adds support for S1600 and S3200, although such hardware
does not exist yet.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Table-based gap count optimization cannot be used if 1394b repeater PHYs
are present.  But it does work with 1394b leaf nodes.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Also remove some errno printouts which will be shown by infrastructure
code anyway.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

cleanup after support of single-buffer requests was dropped
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>

Based on patch "the scheduled removal of RAW1394_REQ_ISO_{SEND,LISTEN}"
from Adrian Bunk, November 20 2006.

This patch also removes the underlying facilities in ohci1394 and
disables them in pcilynx.  That is, hpsb_host_driver.devctl() and
hpsb_host_driver.transmit_packet() are no longer used for iso reception
and transmission.

Since video1394 and dv1394 only work with ohci1394 and raw1394's rawiso
interface has never been implemented in pcilynx, pcilynx is now no
longer useful for isochronous applications.

raw1394 will still handle the request types but will complete the
requests with errors that indicate API version conflicts.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This is upwards compatible, except that integer values other than 0 or 1
are no longer accepted.  But values like "Y", "N", "no", "nnoooh!" work
now.

Also, improve a comment on the serialize_io parameter and make the
ORB_SET_EXCLUSIVE macro ultra-safe.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Association of a host device with a node on NUMA machines optimizes
allocations of skbs given from the networking stack to eth1394.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

After ieee1394 was converted away from class_device like the networking
subsystem was already in 2.6.21, eth1394's device may point to the
fw-host device as its parent again like in 2.6.20.

This affects userspace tools which examine the sysfs representation of
eth1394's device.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Remove the global nodemgr_serialize mutex which enclosed most of the
host thread event loop.  This allows for parallelism between several
host adapter cards.

Properly serialize the driver hooks .update(), .suspend(), .resume(),
and .remove() by means of device->sem.  These hooks can be called from
outside the host threads' contexts.

Get() and put() the device.driver when calling its hooks.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Here is a straightforward conversion to "struct device". The "struct
class_device" will be removed from the kernel.

It seems to work fine for me with and without CONFIG_SYSFS_DEPRECATED
set.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

I was told that only i386 aligns 64 bit integers at 4 bytes boundaries
while all other architectures (32 bit architectures with 64 bit
siblings) align it on 8 bytes boundaries.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Pointed out by Arnd Bergmann:  PPC32 aligns this at 64bit, IA32 packs
it.  A kernel-wide available __compat_u64 which is 4-byte aligned on
AMD64 and IA64 would be nicer though.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Add compat_ioctl.  Although all structures are more or less same,
raw1394_iso_packets got pointer inside, and raw1394_cycle_timer got unwanted
padding in the middle.  I did not add any translation for ioctls passing array
of integers around as integers seem to have same size (32 bits) on all
architectures supported by Linux.
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Acked-by: NDan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)

* write(fd, buf, 52) from 32bit app was returning 56.  Most of callers did not
  care, but some (arm registration) did, and anyway it looks bad if request for
  writing 52 bytes returns 56.  And returning sizeof anything in 'int' is not
  good as well.  So all functions now return '0' instead of
  sizeof(struct raw1394_request) on success, and write() itself provides correct
  return value (it just returns value it was asked to write on success as raw1394
  does not do any partial writes at all).

* Related to this was problem that write() could have returned 0 when kernel
  state would become corrupted and moved to different state than
  opened/initialized/connected.  Now it returns -EBADFD which seemed appropriate.
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Acked-by: NDan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)

read() always failed with -EFAULT.  This was happening due to
raw1394_compat_read copying data to wrong location - access_ok always
failed as 'r' is kernel address, not user.  Whole function just tried to
copy data from 'r' to 'r', which is not good.
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Acked-by: NDan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)

to clarify who is supposed to set what
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

spotted by Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

PIO4 is a maximum PIO mode supported by a driver.  Using "255" as a max_mode
argument to ide_get_best_pio_mode() could result in wrong timings being used
by a driver (for "pio" equal to 5) or OOPS (for "pio" values > 5 && < 255).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Reviewed-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>

The SiS966 has one additional PCI-ID 1180.

If the chipset is using this PCI-ID, the primary channel is connected to the
first PATA-port. The secondary channel is connected to SATA-ports in IDE
emulation mode.  The legacy IO-ports are used.

The including of the PCI-ID into pata_sis is not sufficient, because the legacy
driver in drivers/ide is initialized before pata_sis.
Signed-off-by: NUwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

In 7d12e780 David Howells performed
this evolution:
 "IRQ: Maintain regs pointer globally rather than passing to IRQ handlers"

He correctly updated many of the function definitions that were using this
extra regs pointer parameter but forgot to update some caller sites of
those functions.  The reason the modifications was not properly done on all
drivers is that some drivers were rarely compiled because they are for
AMIGA, or that some code sites were inside #ifdefs where the option is not
set or inside #if 0.

Here is the semantic patch that found the occurences
and fixed the problem.

@ rule1 @
identifier fn;
identifier irq, dev_id;
typedef irqreturn_t;
@@

static irqreturn_t fn(int irq, void *dev_id)
{
   ...
}

@@
identifier rule1.fn;
expression E1, E2, E3;
@@

 fn(E1, E2
-   ,E3
   )
Signed-off-by: NYoann Padioleau <padator@wanadoo.fr>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When we enable the SMCf010 IR device, the Toshiba Portege 4000 BIOS claims
the device is working, but it really isn't configured correctly.  The BIOS
*will* configure it, but only if we call _SRS after (1) reversing the order
of the SIR and FIR I/O port regions and (2) changing the IRQ from
active-high to active-low.

This patch addresses the 2.6.22 regression:
    "no irda0 interface (2.6.21 was OK), smsc does not find chip"

I tested this on a Portege 4000.  The smsc-ircc2 driver correctly detects
the device, and "irattach irda0 -s && irdadump" shows transmitted and
received packets.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Yeah, we could have just disabled it, but there's work on a new one that
isn't as fundamentally broken, so there really doesn't seem to be any
point in keeping it around.

The recent timer cleanup broke the only valid use, and when I say
"valid", I obviously mean "totally broken".  So it's not like it works,
or really even can work in the current format that uses the unsafe
"panic" LED blinking routines..
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/ide/setup-pci.c: In function 'ide_scan_pcibus':
drivers/ide/setup-pci.c:879: warning: ignoring return value of '__pci_register_driver', declared with attribute warn_unused_result
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Recently the PLL input clock of Promise 2027x is sometimes detected
higher than expected (e.g. 20.027 MHz compared to 16.714 MHz).
It seems sometimes the mdelay() function is not as precise as it
used to be. Per Alan's advice, HT or power management might affect
the precision of mdelay().

This patch calls gettimeofday() to measure the time elapsed and
calculate the PLL input clock accordingly.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bahadir Balban <bahadir.balban@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

SWDMA modes are unsupported by it821x.  Attempts to tune SWDMA modes always
fail (due to sanity check in ->speedproc) and result in PIO being tuned.

* Fix incorrect SWDMA mask so core code won't try these modes and will just
  tune PIO if no other DMA modes are available.

* Bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

* Driver can't skip programming transfer mode on the device in amd_set_drive()
  (similar fix has been applied to via82cxxx driver ages ago).

* While at it remove redundant warning (ide_config_drive_speed() already
  produces more valuable one).

* Bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The HPT36x chips finally turned out to have the channel enable bits -- however,
badly implemented.  Make use of them despite it's probably only going to burden
the driver's code -- assuming both channels are always enabled by the HighPoint
BIOS anyway...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NLinas Vepstas <linas@austin.ibm.com>
Cc: michal.kepien@poczta.onet.pl
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add the MAXTOR STM3320620A drive into the UltraDMA/66 mode blacklist
for the HPT36x chips.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Found by a static analyser. It is in theory possible we dereference
dev->id when it has become invalid. Re-order to avoid this.

Not needed for new-ide as we no longer support the crazy exabyte nest stuff
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Look at wait_drive_not_busy in drivers/ide/ide-taskfile.c:

    static u8 wait_drive_not_busy(ide_drive_t *drive)
    {
            ide_hwif_t *hwif = HWIF(drive);
            int retries = 100;
            u8 stat;

            /*
             * Last sector was transfered, wait until drive is ready.
             * This can take up to 10 usec, but we will wait max 1 ms
             * (drive_cmd_intr() waits that long).
             */
            while (((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) && retries--)
                    udelay(10);

            if (!retries)
                    printk(KERN_ERR "%s: drive still BUSY!\n", drive->name);

            return stat;
    }

`printk' is never called because `retries' never holds zero at the
outside of `while' loop: when `retries' holds zero at the while's loop
condition, `retries' will hold -1 at the if condition.
Signed-off-by: NMasatake YAMATO <jet@gyve.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: joe@perches.com
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

if the call to budget_register() fails in ttpci_budget_int(),
ttpci_budget_init() returns success. The attached patch will
fix this problem.
Signed-off-by: NHartmut Birr <e9hack@googlemail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>