Skip to content

K
Kernel

openeuler / Kernel
大约 1 年 前同步成功

通知 5
Star 0
Fork 0
K
Kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 01 9月, 2014 1 次提交
  3. 24 8月, 2014 2 次提交
  5. 22 8月, 2014 5 次提交
  7. 20 8月, 2014 3 次提交
  9. 19 8月, 2014 6 次提交
  11. 18 8月, 2014 9 次提交
    • I
      drm/i915: don't try to retrain a DP link on an inactive CRTC · 1a125d8a
      由 Imre Deak 提交于 
      Atm we may retrain the DP link even if the CRTC is inactive through
HPD work->intel_dp_check_link_status(). This in turn can lock up the PHY
(at least on BYT), since the DP port is disabled.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81948Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
      1a125d8a
    • I
      drm/i915: make sure VDD is turned off during system suspend · 07f9cd0b
      由 Imre Deak 提交于 
      Atm we may leave eDP VDD enabled during system suspend after the CRTCs
are disabled through an HPD->DPCD read event. So disable VDD during
suspend at a point when no HPDs can occur.

Note that runtime suspend doesn't have the same problem, since there the
RPM ref held by VDD provides already the needed serialization.

v2:
- add note to commit message about the runtime suspend path (Ville)
- use edp_panel_vdd_off_sync(), so we can keep the WARN in
  edp_panel_vdd_off() (Ville)
v3:
- rebased on -fixes (for_each_intel_encoder()->list_for_each_entry())
  (Imre)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
[Jani: fix sparse warning reported by Fengguang Wu]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
      07f9cd0b
    • I
      drm/i915: cancel hotplug and dig_port work during suspend and unload · 1d0d343a
      由 Imre Deak 提交于 
      Make sure these work handlers don't run after we system suspend or
unload the driver. Note that we don't cancel the handlers during runtime
suspend. That could lead to a lockup, since we take a runtime PM ref
from the handlers themselves. Fortunaltely canceling there is not needed
since the RPM ref itself provides for the needed serialization.

v2:
- fix the order of canceling dig_port_work wrt. hotplug_work (Ville)
- zero out {long,short}_hpd_port_mask and hpd_event_bits for speed
  (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
      1d0d343a
    • I
      drm/i915: fix HPD IRQ reenable work cancelation · 6323751d
      由 Imre Deak 提交于 
      Atm, the HPD IRQ reenable timer can get rearmed right after it's
canceled. Also to access the HPD IRQ mask registers we need to wake up
the HW.

Solve both issues by converting the reenable timer to a delayed work and
grabbing a runtime PM reference in the work. By this we can also forgo
canceling the timer during runtime suspend, since the only important
thing there is that the HW is awake when we write the registers and
that's ensured by the RPM ref. So do the cancelation only during driver
unload time; this is also a requirement for an upcoming patch where we
want to cancel all HPD related works only during system suspend and
driver unload time, but not during runtime suspend.

Note that there is still a race between the HPD IRQ reenable work and
drm_irq_uninstall() during driver unload, where the work can reenable
the HPD IRQs disabled by drm_irq_uninstall(). This isn't a problem since
the HPD IRQs will still be effectively masked by the first level
interrupt mask.

v2-3:
- unchanged
v4:
- use proper API for changing the expiration time for an already pending
  delayed work (Jani)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
      6323751d
    • I
      drm/i915: take display port power domain in DP HPD handler · 1c767b33
      由 Imre Deak 提交于 
      Ville noticed that we can call ibx_digital_port_connected() which accesses
the HW without holding any power well/runtime pm reference. Fix this by
holding a display port power domain reference around the whole hpd_pulse
handler.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
      1c767b33
    • D
      Merge branch 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux · c39502c5
      由 Dave Airlie 提交于 
      radeon fixes for 3.17, kind of all over the place (dpm, GPUVM, etc.)
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: Remove duplicate include from Makefile
  drm/radeon/dpm: select the appropriate vce power state for KV/KB/ML
  drm/radeon: Add ability to get and change dpm state when radeon PX card is turned off
  drm/radeon: Add missing lines to ci_set_thermal_temperature_range
  drm/radeon: Always flush VM again on < CIK
  drm/radeon: add a check for allocation failure (v2)
  drm/radeon: use pfp for all vm_flush related updates
  drm/radeon: add bapm module parameter
      c39502c5
    • V
      drm/i915: Don't try to enable cursor from setplane when crtc is disabled · 1add143c
      由 Ville Syrjälä 提交于 
      Make sure the cursor gets fully clipped when enabling it on a disabled
crtc via setplane. This will prevent the lower level code from
attempting to enable the cursor in hardware.

Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
      1add143c
    • V
      drm/i915: Skip load detect when intel_crtc->new_enable==true · a459249c
      由 Ville Syrjälä 提交于 
      During suspend we turn off the crtcs, but leave the staged config in
place so that we can restore the display(s) to their previous state on
resume.

During resume when we attempt to apply the force pipe A quirk we use the
load detect mechanism. That doesn't check whether there was an already
staged configuration for the crtc since that's not even possible during
normal runtime load detection. But during resume it is possible, and if
we just blindly go and overwrite the staged crtc configuration for the
load detection we can no longer restore the display to the correct
state.

Even worse, we don't even clear all the staged connector->encoder->crtc
links so we may end up using a cloned setup for the load detection, and
after we're done we just clear the links related to the VGA output
leaving the links for the other outputs in place. This will eventually
result in calling intel_set_mode() with mode==NULL but with valid
connector->encoder->crtc links which will result in dereferencing the
NULL mode since the code thinks it will have to a modeset.

To avoid these problems don't use any crtc with new_enabled==true for
load detection.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (for 3.16)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
      a459249c
    • V
      drm/i915: Fix locking for intel_enable_pipe_a() · 208bf9fd
      由 Ville Syrjälä 提交于 
      intel_enable_pipe_a() gets called with all the modeset locks already
held (by drm_modeset_lock_all()), so trying to grab the same
locks using another drm_modeset_acquire_ctx is going to fail miserably.

Move most of the drm_modeset_acquire_ctx handling (init/drop/fini)
out from intel_{get,release}_load_detect_pipe() into the callers
(intel_{crt,tv}_detect()). Only the actual locking and backoff
handling is left in intel_get_load_detect_pipe(). And in
intel_enable_pipe_a() we just share the mode_config.acquire_ctx from
drm_modeset_lock_all() which is already holding all the relevant locks.

It's perfectly legal to lock the same ww_mutex multiple times using the
same ww_acquire_ctx. drm_modeset_lock() will convert the returned
-EALREADY into 0, so the caller doesn't need to do antyhing special.

Fixes a hang on resume on my 830.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
      208bf9fd
  13. 17 8月, 2014 1 次提交
  15. 16 8月, 2014 13 次提交