Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 26 3月, 2019 2 次提交
  3. 20 2月, 2019 1 次提交
  5. 09 2月, 2019 5 次提交
    • R
      iw_cxgb4: fix srqidx leak during connection abort · f368ff18
      由 Raju Rangoju 提交于 
      When an application aborts the connection by moving QP from RTS to ERROR,
then iw_cxgb4's modify_rc_qp() RTS->ERROR logic sets the
*srqidxp to 0 via t4_set_wq_in_error(&qhp->wq, 0), and aborts the
connection by calling c4iw_ep_disconnect().

c4iw_ep_disconnect() does the following:
 1. sends up a close_complete_upcall(ep, -ECONNRESET) to libcxgb4.
 2. sends abort request CPL to hw.

But, since the close_complete_upcall() is sent before sending the
ABORT_REQ to hw, libcxgb4 would fail to release the srqidx if the
connection holds one. Because, the srqidx is passed up to libcxgb4 only
after corresponding ABORT_RPL is processed by kernel in abort_rpl().

This patch handle the corner-case by moving the call to
close_complete_upcall() from c4iw_ep_disconnect() to abort_rpl().  So that
libcxgb4 is notified about the -ECONNRESET only after abort_rpl(), and
libcxgb4 can relinquish the srqidx properly.
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
      f368ff18
    • R
      iw_cxgb4: complete the cached SRQ buffers · 11a27e21
      由 Raju Rangoju 提交于 
      If TP fetches an SRQ buffer but ends up not using it before the connection
is aborted, then it passes the index of that SRQ buffer to the host in
ABORT_REQ_RSS or ABORT_RPL CPL message.

But, if the srqidx field is zero in the received ABORT_RPL or
ABORT_REQ_RSS CPL, then we need to read the tcb.rq_start field to see if
it really did have an RQE cached. This works around a case where HW does
not include the srqidx in the ABORT_RPL/ABORT_REQ_RSS CPL.

The final value of rq_start is the one present in TCB with the
TF_RX_PDU_OUT bit cleared. So, we need to read the TCB, examine the
TF_RX_PDU_OUT (bit 49 of t_flags) in order to determine if there's a rx
PDU feedback event pending.
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
      11a27e21
    • S
      iw_cxgb4: use tos when finding ipv6 routes · c8a7eb55
      由 Steve Wise 提交于 
      When IPv6 support was added, the correct tos was not passed to
cxgb_find_route6(). This potentially results in the wrong route entry.

Fixes: 830662f6 ("RDMA/cxgb4: Add support for active and passive open connection with IPv6 address")
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
      c8a7eb55
    • S
      iw_cxgb4: use tos when importing the endpoint · cb3ba0bd
      由 Steve Wise 提交于 
      import_ep() is passed the correct tos, but doesn't use it correctly.

Fixes: ac8e4c69 ("cxgb4/iw_cxgb4: TOS support")
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
      cb3ba0bd
    • S
      iw_cxgb4: use listening ep tos when accepting new connections · 7235ea22
      由 Steve Wise 提交于 
      If the parent listening endpoint has a service type set, then use that
when setting up the connection.  This allows server-side applications to
mandate the tos for passive side connections via rdma_set_service_type()
on the listening endpoints.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
      7235ea22
  7. 16 1月, 2019 1 次提交
  9. 24 11月, 2018 1 次提交
  11. 22 11月, 2018 1 次提交
  13. 09 11月, 2018 1 次提交
  15. 22 9月, 2018 1 次提交
  17. 08 8月, 2018 1 次提交
  19. 01 8月, 2018 2 次提交
  21. 26 7月, 2018 1 次提交
  23. 19 6月, 2018 1 次提交
  25. 23 5月, 2018 1 次提交
  27. 30 12月, 2017 1 次提交
  29. 14 12月, 2017 1 次提交
  31. 14 11月, 2017 1 次提交
  33. 18 10月, 2017 1 次提交
  35. 15 10月, 2017 4 次提交
  37. 29 9月, 2017 2 次提交
    • S
      iw_cxgb4: add referencing to wait objects · 2015f26c
      由 Steve Wise 提交于 
      For messages sent from the host to fw that solicit a reply from fw,
the c4iw_wr_wait struct pointer is passed in the host->fw message, and
included in the fw->host fw6_msg reply.  This allows the sender to wait
until the reply is received, and the code processing the ingress reply
to wake up the sender.

If c4iw_wait_for_reply() times out, however, we need to keep the
c4iw_wr_wait object around in case the reply eventually does arrive.
Otherwise we have touch-after-free bugs in the wake_up paths.

This was hit due to a bad kernel driver that blocked ingress processing
of cxgb4 for a long time, causing iw_cxgb4 timeouts, but eventually
resuming ingress processing and thus hitting the touch-after-free bug.

So I want to fix iw_cxgb4 such that we'll at least keep the wait object
around until the reply comes.  If it never comes we leak a small amount of
memory, but if it does come late, we won't potentially crash the system.

So add a kref struct in the c4iw_wr_wait struct, and take a reference
before sending a message to FW that will generate a FW6 reply.  And remove
the reference (and potentially free the wait object) when the reply
is processed.

The ep code also uses the wr_wait for non FW6 CPL messages and doesn't
embed the c4iw_wr_wait object in the message sent to firmware.  So for
those cases we add c4iw_wake_up_noref().

The mr/mw, cq, and qp object create/destroy paths do need this reference
logic.  For these paths, c4iw_ref_send_wait() is introduced to take the
wr_wait reference, send the msg to fw, and then wait for the reply.

So going forward, iw_cxgb4 either uses c4iw_ofld_send(),
c4iw_wait_for_reply() and c4iw_wake_up_noref() like is done in the some
of the endpoint logic, or c4iw_ref_send_wait() and c4iw_wake_up_deref()
(formerly c4iw_wake_up()) when sending messages with the c4iw_wr_wait
object pointer embedded in the message and resulting FW6 reply.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>
      2015f26c
    • S
      iw_cxgb4: allocate wait object for each ep object · ef885dc6
      由 Steve Wise 提交于 
      Remove the embedded c4iw_wr_wait object in preparation for correctly
handling timeouts.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>
      ef885dc6
  39. 27 9月, 2017 2 次提交
  41. 23 9月, 2017 3 次提交
  43. 18 8月, 2017 1 次提交
  45. 21 6月, 2017 1 次提交
    • Y
      net: introduce __skb_put_[zero, data, u8] · de77b966
      由 yuan linyu 提交于 
      follow Johannes Berg, semantic patch file as below,
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = __skb_put(skb, len);
+p = __skb_put_zero(skb, len);
|
-p = (t)__skb_put(skb, len);
+p = __skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)

@@
identifier p;
expression len;
expression skb;
type t;
@@
(
-t p = __skb_put(skb, len);
+t p = __skb_put_zero(skb, len);
)
... when != p
(
-memset(p, 0, len);
)

@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = __skb_put(skb, sizeof(t));
+p = __skb_put_zero(skb, sizeof(t));
|
-p = (t *)__skb_put(skb, sizeof(t));
+p = __skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)

@@
expression skb, len;
@@
-memset(__skb_put(skb, len), 0, len);
+__skb_put_zero(skb, len);

@@
expression skb, len, data;
@@
-memcpy(__skb_put(skb, len), data, len);
+__skb_put_data(skb, data, len);

@@
expression SKB, C, S;
typedef u8;
identifier fn = {__skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      de77b966
  47. 16 6月, 2017 3 次提交
    • J
      networking: make skb_push & __skb_push return void pointers · d58ff351
      由 Johannes Berg 提交于 
      It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

    @@
    expression SKB, LEN;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    @@
    - fn(SKB, LEN)[0]
    + *(u8 *)fn(SKB, LEN)

Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d58ff351
    • J
      networking: make skb_put & friends return void pointers · 4df864c1
      由 Johannes Berg 提交于 
      It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_put, __skb_put };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_put, __skb_put };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

which actually doesn't cover pskb_put since there are only three
users overall.

A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4df864c1
    • J
      networking: convert many more places to skb_put_zero() · b080db58
      由 Johannes Berg 提交于 
      There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.

The following spatch found many more and also removes the
now unnecessary casts:

    @@
    identifier p, p2;
    expression len;
    expression skb;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_zero(skb, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_zero(skb, len);
    )
    ... when != p
    (
    p2 = (t2)p;
    -memset(p2, 0, len);
    |
    -memset(p, 0, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_zero(skb, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_zero(skb, sizeof(t));
    )
    ... when != p
    (
    p2 = (t2)p;
    -memset(p2, 0, sizeof(*p));
    |
    -memset(p, 0, sizeof(*p));
    )

    @@
    expression skb, len;
    @@
    -memset(skb_put(skb, len), 0, len);
    +skb_put_zero(skb, len);

Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b080db58
  49. 08 6月, 2017 1 次提交