* Firmware Initialization with SCM enabled based on NVRAM setting and
  firmware support (About Firmware).

* Enable PUREX and add support for fabric performance impact
  notification (FPIN) handling.

* Allocate a default PUREX item for each vha to handle memory allocation
  failures in ISR.

Link: https://lore.kernel.org/r/20200630102229.29660-3-njavali@marvell.comReviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NShyam Sundar <ssundar@marvell.com>
Signed-off-by: NArun Easi <aeasi@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

SAN Congestion Management generates ELS pkts whose size can vary and be >
64 bytes. Change the PUREX handling code to support non-standard ELS pkt
size.

Link: https://lore.kernel.org/r/20200630102229.29660-2-njavali@marvell.comReviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NShyam Sundar <ssundar@marvell.com>
Signed-off-by: NArun Easi <aeasi@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Annotate members of FC protocol and firmware dump data structures as big
endian. Annotate members of RISC control structures as little endian.
Annotate mailbox registers as little endian. Annotate the mb[] arrays as
CPU-endian because communication of the mb[] values with the hardware
happens through the readw() and writew() functions. readw() converts from
__le16 to u16 and writew() converts from u16 to __le16. Annotate 'handles'
as CPU-endian because for the firmware these are opaque values.

Link: https://lore.kernel.org/r/20200518211712.11395-15-bvanassche@acm.org
CC: Hannes Reinecke <hare@suse.de>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This was suggested by Daniel Wagner.

Link: https://lore.kernel.org/r/20200518211712.11395-12-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: NArun Easi <aeasi@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Make the MMIO accessors strongly typed such that the compiler checks
whether the accessor function is used that matches the register width. Fix
those MMIO accesses where another number of bits was read or written than
the size of the register.

Link: https://lore.kernel.org/r/20200518211712.11395-11-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead of passing an argument to the firmware dumping functions that tells
these functions whether or not to obtain the hardware lock, obtain that
lock before calling these functions. This patch fixes the following
recently introduced C=2 build error:

  CHECK   drivers/scsi/qla2xxx/qla_tmpl.c
drivers/scsi/qla2xxx/qla_tmpl.c:1133:1: error: Expected ; at end of statement
drivers/scsi/qla2xxx/qla_tmpl.c:1133:1: error: got }
drivers/scsi/qla2xxx/qla_tmpl.h:247:0: error: Expected } at end of function
drivers/scsi/qla2xxx/qla_tmpl.h:247:0: error: got end-of-input

Link: https://lore.kernel.org/r/20200518211712.11395-4-bvanassche@acm.org
Fixes: cbb01c2f ("scsi: qla2xxx: Fix MPI failure AEN (8200) handling")
Cc: Arun Easi <aeasi@marvell.com>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The bitfields mpi_fw_dump_reading and mpi_fw_dumped are currently signed
which is not recommended as the representation is an implementation defined
behaviour.  Fix this by making the bit-fields unsigned ints.

Link: https://lore.kernel.org/r/20200428102013.1040598-1-colin.king@canonical.com
Fixes: cbb01c2f ("scsi: qla2xxx: Fix MPI failure AEN (8200) handling")
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Today, upon an MPI failure AEN, on top of collecting an MPI dump, a regular
firmware dump is also taken and then chip reset. This is disruptive to IOs
and not required. Make the firmware dump collection, followed by chip
reset, optional (not done by default).

Firmware dump buffer and MPI dump buffer are independent of each
other with this change and each can have dump that was taken at two
different times for two different issues. The MPI dump is saved in a
separate buffer and is retrieved differently from firmware dump.

To collect full dump on MPI failure AEN, a module parameter is
introduced:
    ql2xfulldump_on_mpifail (default: 0)

Link: https://lore.kernel.org/r/20200331104015.24868-2-njavali@marvell.comReported-by: Nkbuild test robot <lkp@intel.com>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NArun Easi <aeasi@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

commit e4e3a2ce ("scsi: qla2xxx: Add ability to autodetect SFP
type") takes a heavy handed approach to BPM (Buffer Plus Management)
enablement:

1) During hardware initialization, if an LR-capable transceiver is
   recognized, the driver schedules a disruptive post-initialization
   chip-reset (ISP-ABORT) to allow the BPM settings to be sent to the
   firmware.  This chip-reset will result in (short-term) path-loss to
   all fc-rports and their attached SCSI devices.

2) LR-detection is triggered during any link-up event, resulting in a
   refresh and potential chip-reset

Based on firmware-team guidance, upon LR-capable transceiver
recognition, the driver's hardware initialization code will now
re-execute firmware with the new BPM settings, then continue on with
driver initialization.  To address the second issue, the driver
performs LR-capable detection upon the driver receiving a
transceiver-insertion asynchronous event from firmware.  No short-term
path loss is needed with this new semantic.

Link: https://lore.kernel.org/r/20200226224022.24518-10-hmadhani@marvell.comSigned-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NAndrew Vasquez <andrewv@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There's no point checking flags.disable_msix_handshake in the
interrupt handler hot-path.  Instead perform the check during
queue-pair instantiation and use the proper interrupt handler.

Link: https://lore.kernel.org/r/20200226224022.24518-8-hmadhani@marvell.comSigned-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NAndrew Vasquez <andrewv@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch allows sparse to verify the endianness of the arguments passed
to make_handle().

Link: https://lore.kernel.org/r/20200220043441.20504-5-bvanassche@acm.org
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Reviewed-by: NRoman Bolshakov <r.bolshakov@yadro.com>
Acked-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead of changing endianness in-place, write the data in CPU endian
format in another buffer and copy that buffer back. This patch does not
change any functionality but silences some sparse endianness warnings.

Link: https://lore.kernel.org/r/20200220043441.20504-3-bvanassche@acm.org
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Reviewed-by: NRoman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Since the SCSI core does not reuse the tag of the SCSI command that is
being aborted by .eh_abort() before .eh_abort() has finished it is not
necessary to check from inside that callback whether or not the SCSI
command has already completed. Instead, rely on the firmware to return an
error code when attempting to abort a command that has already
completed. Additionally, rely on the firmware to return an error code when
attempting to abort an already aborted command.

In qla2x00_abort_srb(), use blk_mq_request_started() instead of
sp->completed and sp->aborted.

Link: https://lore.kernel.org/r/20200220043441.20504-2-bvanassche@acm.org
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Reviewed-by: NRoman Bolshakov <r.bolshakov@yadro.com>
Acked-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds deferred queue for processing aborts and RDP in the driver.

Link: https://lore.kernel.org/r/20200212214436.25532-14-hmadhani@marvell.comSigned-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds support for extended FDMI commands and cleans up code to
reduce duplication.

Link: https://lore.kernel.org/r/20200212214436.25532-10-hmadhani@marvell.comSigned-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds RDP command support in the driver. With the help of new
ql2xsmartsan parameter, driver will use PUREX IOCB mode to send RDP command
to switch and will be able to receive various diagnostic data.

Link: https://lore.kernel.org/r/20200212214436.25532-8-hmadhani@marvell.comSigned-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch prepares code for implementing Vendor specific extended FDMI/RDP
commands. It also addes support for MBC_GET_PORT_DATABASE and
MBC_GET_RNID_PARAMS commands.

Link: https://lore.kernel.org/r/20200212214436.25532-7-hmadhani@marvell.comSigned-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes endian warning for fc_host_stats.

Link: https://lore.kernel.org/r/20200212214436.25532-6-hmadhani@marvell.comSigned-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds sysfs node to show D-Port diag data.

Link: https://lore.kernel.org/r/20200212214436.25532-4-hmadhani@marvell.comSigned-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch provides an interface to do the following (using MBC 0x3B):

 - Displays (in hex) the LED config words for all three LEDs.

 - Programs the config words for one LED or for all three LEDs.

The sysfs node defined is named beacon_config.

First, to allow driver to gain LED control, do this:
 # echo 1 > /sys/class/scsi_host/host#/beacon

Then, to display config words for all three LEDs do this:
 # cat /sys/class/scsi_host/host#/beacon_config

To set config words for all three LEDs do this:
 # echo 3 xxxx yyyy zzzz > /sys/class/scsi_host/host#/beacon_config

Or, to set config word for a specific single LED n do this:
 # echo n xxxx > /sys/class/scsi_host/host#/beacon_config
  where n is the LED number (0, 1, 2)

Finally, to restore LED control back to firmware, do this:
 # echo 0 > /sys/class/scsi_host/host#/beacon

Link: https://lore.kernel.org/r/20200212214436.25532-2-hmadhani@marvell.comSigned-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Declare qla_hw_data.flt as a qla_flt_header pointer instead of as a void
pointer. Add a zero-length array at the end of struct qla_flt_header to
make it clear that qla_flt_header and qla_flt_region are contiguous. This
patch removes several casts but does not change any functionality.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Link: https://lore.kernel.org/r/20191219004706.39039-1-bvanassche@acm.orgReviewed-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Session is stuck if driver sees FW has received a PRLI. Driver allows FW to
finish with processing of PRLI by checking back with FW at a later time to
see if the PRLI has finished. Instead, driver failed to push forward after
re-checking PRLI completion.

Fixes: ce0ba496 ("scsi: qla2xxx: Fix stuck login session")
Cc: stable@vger.kernel.org # 5.3
Link: https://lore.kernel.org/r/20191217220617.28084-9-hmadhani@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch removes unused qla2x00_async_logout_done from the code.

Link: https://lore.kernel.org/r/20191217220617.28084-5-hmadhani@marvell.comSigned-off-by: NShyam Sundar <ssundar@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds a shadow variable to hold disc_state history for the fcport
and prints state transition when the logging is enabled.

Link: https://lore.kernel.org/r/20191217220617.28084-4-hmadhani@marvell.comSigned-off-by: NShyam Sundar <ssundar@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Target makes implicit LOGO on session teardown. LOGO ELS is not send on the
wire and initiator is not aware that target no longer wants talking to
it. Initiator keeps sending I/O requests, target responds with BA_RJT, they
time out and then initiator sends ABORT TASK (ABTS-LS).

Current behaviour incurs unneeded I/O timeout and can be fixed for some
initiators by making explicit LOGO on session deletion.

Link: https://lore.kernel.org/r/20191125165702.1013-3-r.bolshakov@yadro.comReviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NRoman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoid an uninitialized value (0) for ha->fc4_type_priority being falsely
interpreted as NVMe priority. Not strictly needed any more after the
previous patch, but makes the fc4_type_priority handling more explicit.

Link: https://lore.kernel.org/r/20191107224839.32417-3-martin.wilck@suse.comTested-by: NDavid Bond <dbond@suse.com>
Acked-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin Wilck <mwilck@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current code assumes abort will remove the original command from the active
list where scsi_done will not be called. Instead, the eh_abort thread will
do the scsi_done. That is not the case.  Instead, we have a double
scsi_done calls triggering use after free.

Abort will tell FW to release the command from FW possesion. The original
command will return to ULP with error in its normal fashion via scsi_done.
eh_abort path would wait for the original command completion before
returning.  eh_abort path will not perform the scsi_done call.

Fixes: 219d27d7 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands")
Cc: stable@vger.kernel.org # 5.2
Link: https://lore.kernel.org/r/20191105150657.8092-6-hmadhani@marvell.comReviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NArun Easi <aeasi@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

On switch, fabric and mgt command timeout, driver send Abort to tell FW to
return the original command.  If abort is timeout, then return both Abort
and original command for cleanup.

Fixes: 219d27d7 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands")
Cc: stable@vger.kernel.org # 5.2
Link: https://lore.kernel.org/r/20191105150657.8092-3-hmadhani@marvell.comReviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Some storage arrays advertise FCP LUNs and NVMe namespaces behind the same
WWN.  The driver now offers a user option by way of NVRAM parameter to
allow users to choose, on a per port basis, the kind of FC-4 type they
would like to prioritize for login.

Link: https://lore.kernel.org/r/20190912180918.6436-9-hmadhani@marvell.comSigned-off-by: NMichael Hernandez <mhernandez@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix stalled link recovery for N2N with FC-NVMe connection.

Link: https://lore.kernel.org/r/20190912180918.6436-6-hmadhani@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In the case of NPIV port is being torn down, this patch will set a flag to
indicate VPORT_DELETE. This would prevent relogin to be triggered.

Link: https://lore.kernel.org/r/20190912180918.6436-5-hmadhani@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch reduces code duplication.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead of calling qla2x00_fcport_event_handler() and letting the switch
statement inside that function decide which other function to call, call
the latter function directly. Remove the event member from the event_arg
structure because it is no longer needed. Remove the
qla_handle_els_plogi_done() function because it is never called.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It is easy to mix up the QLA_* and the MBS_* status codes. Complain loudly
if that happens.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Split srb_cmd.ctx into two pointers such that the compiler can check the
type of that pointer.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead of allocating a struct srb dynamically from inside .queuecommand(),
set qla2xxx_driver_template.cmd_size such that struct scsi_cmnd and struct
srb are contiguous. Do not call QLA_QPAIR_MARK_BUSY() /
QLA_QPAIR_MARK_NOT_BUSY() for SRBs associated with SCSI commands. That is
safe because scsi_remove_host() is called before queue pairs are deleted
and scsi_remove_host() waits for all outstanding SCSI commands to finish.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Since all pointers passed to the srb_t.done() and srb_t.free() functions
have type srb_t, change the type of the first argument of these functions
from void * into struct srb *. This allows the compiler to verify the
argument types for these functions. This patch does not change any
functionality.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Introduce the be_id_t and le_id_t data types for Fibre Channel source and
destination ID formats supported by the firmware instead of using an
uint8_t[3] array. Introduce functions for converting from and to the
port_id_t data types. This patch does not change the behavior of the
qla2xxx driver but improves source code readability and also allows the
compiler to verify the endianness of Fibre Channel IDs.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Pass the output buffer size to the code that generates a PCI info string
and check the output buffer size while generating a PCI info string.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch does not change any functionality but fixes a Coverity complaint
about using a scalar as an array.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>