Texas Instruments' K3 generation SoCs has an IP Interrupt Aggregator
which is an interrupt controller that does the following:
- Converts events to interrupts that can be understood by
  an interrupt router.
- Allows for multiplexing of events to interrupts.

Configuration of the interrupt aggregator registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol. Add the required infrastructure to
allow the allocation and routing of these events.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Texas Instruments' K3 generation SoCs has an IP Interrupt Router
that does allows for redirection of input interrupts to host
interrupt controller. Interrupt Router inputs are either from a
peripheral or from an Interrupt Aggregator which is another
interrupt controller.

Configuration of the interrupt router registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol.

Add support for Interrupt Router driver over TISCI protocol.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

IRQ_DOMAIN_HIERARCHY selects IRQ_DOMAIN, hence there is no need for
drivers to select both.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The cp-intc driver has now been cleaned up. Move it to drivers/irqchip
where it belongs.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The aintc driver has now been cleaned up. Move it to drivers/irqchip
where it belongs. There's no device-tree support for any dm* board so
there's no IRQCHIP_OF_DECLARE() - there's only the exported init
function called from machine code.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This controller appeared on Loongson-1 family MCUs
including Loongson-1B and Loongson-1C.
Signed-off-by: NJiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The irqsteer block is a interrupt multiplexer/remapper found on the
i.MX8 line of SoCs.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The Cirrus Logic Madera codecs (Cirrus Logic CS47L35/85/90/91 and WM1840)
are highly complex devices containing up to 7 programmable DSPs and many
other internal sources of interrupts plus a number of GPIOs that can be
used as interrupt inputs. The large number (>150) of internal interrupt
sources are managed by an on-board interrupt controller.

This driver provides the handling for the interrupt controller. As the
codec is accessed via regmap, we can make use of the generic IRQ
functionality from regmap to do most of the work. Only around half of
the possible interrupt source are currently of interest from the driver
so only this subset is defined. Others can be added in future if needed.

The KConfig options are not user-configurable because this driver is
mandatory so is automatically included when the parent MFD driver is
selected.
Signed-off-by: NRichard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Add interrupt driver for RDA Micro RDA8810PL SoC.
Signed-off-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The driver is for C-SKY APB bus interrupt controller. It's a simple
interrupt controller which use pending reg to detect the irq and use
enable/disable reg to mask/unmask interrupt sources.

A lot of SOCs based on C-SKY CPU use the interrupt controller as root
controller.
Signed-off-by: NGuo Ren <ren_guo@c-sky.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>

The driver is for C-SKY SMP interrupt controller. It support 16
soft-irqs, 16 private-irqs, and 992 max external-irqs, a total of
1024 interrupts.

C-SKY CPU 807/810/860 SMP/non-SMP could use it.
Signed-off-by: NGuo Ren <ren_guo@c-sky.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>

This is a cascaded interrupt controller in the AP806 GIC that collapses
SEIs (System Error Interrupt) coming from the AP and the CPs (through
the ICU).

The SEI handles up to 64 interrupts. The first 21 interrupts are wired
from the AP. The next 43 interrupts are from the CPs and are triggered
through MSI messages. To handle this complexity, the driver has to
declare to the upper layer: one IRQ domain for the wired interrupts,
one IRQ domain for the MSIs; and acts as a MSI controller ('parent')
by declaring an MSI domain.
Suggested-by: NHaim Boot <hayim@marvell.com>
Suggested-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Add a driver for the SiFive implementation of the RISC-V Platform Level
Interrupt Controller (PLIC).  The PLIC connects global interrupt sources
to the local interrupt controller on each hart.

This driver is based on the driver in the RISC-V tree from Palmer Dabbelt,
but has been almost entirely rewritten since, and includes many fixes
from Atish Patra.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAtish Patra <atish.patra@wdc.com>
[Binding update by Palmer]
Signed-off-by: NPalmer Dabbelt <palmer@sifive.com>

Now that every user of MULTI_IRQ_HANDLER has been convereted over to use
GENERIC_IRQ_MULTI_HANDLER remove the references to MULTI_IRQ_HANDLER.
Signed-off-by: NPalmer Dabbelt <palmer@sifive.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: linux@armlinux.org.uk
Cc: catalin.marinas@arm.com
Cc: Will Deacon <will.deacon@arm.com>
Cc: jonas@southpole.se
Cc: stefan.kristiansson@saunalahti.fi
Cc: shorne@gmail.com
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: nicolas.pitre@linaro.org
Cc: vladimir.murzin@arm.com
Cc: keescook@chromium.org
Cc: jinb.park7@gmail.com
Cc: yamada.masahiro@socionext.com
Cc: alexandre.belloni@bootlin.com
Cc: pombredanne@nexb.com
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: kstewart@linuxfoundation.org
Cc: jhogan@kernel.org
Cc: mark.rutland@arm.com
Cc: ard.biesheuvel@linaro.org
Cc: james.morse@arm.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: openrisc@lists.librecores.org
Link: https://lkml.kernel.org/r/20180622170126.6308-6-palmer@sifive.com

GENERIC_IRQ_MULTI_HANDLER is incompatible with MULTI_IRQ_HANDLER because
they define the same symbols.  Multiple generic irqchip drivers select
MULTI_IRQ_HANDLER, which is now defined on all architectures that
provide set_handle_irq().

To solve this select GENERIC_IRQ_MULTI_HANDLER for all drivers that used to
select MULTI_IRQ_HANDLER, but only when MULTI_IRQ_HANDLER doesn't exist.

After that every architecture can be converted over from MULTI_IRQ_HANDLER
to GENERIC_IRQ_MULTI_HANDLER before removing the extra MULTI_IRQ_HANDLER
scaffolding.
Signed-off-by: NPalmer Dabbelt <palmer@sifive.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: linux@armlinux.org.uk
Cc: catalin.marinas@arm.com
Cc: Will Deacon <will.deacon@arm.com>
Cc: jonas@southpole.se
Cc: stefan.kristiansson@saunalahti.fi
Cc: shorne@gmail.com
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: nicolas.pitre@linaro.org
Cc: vladimir.murzin@arm.com
Cc: keescook@chromium.org
Cc: jinb.park7@gmail.com
Cc: yamada.masahiro@socionext.com
Cc: alexandre.belloni@bootlin.com
Cc: pombredanne@nexb.com
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: kstewart@linuxfoundation.org
Cc: jhogan@kernel.org
Cc: mark.rutland@arm.com
Cc: ard.biesheuvel@linaro.org
Cc: james.morse@arm.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: openrisc@lists.librecores.org
Cc: Shea Levy <shea@shealevy.com>
Link: https://lkml.kernel.org/r/20180622170126.6308-2-palmer@sifive.com

The Microsemi Ocelot SoC has a pretty simple IRQ controller in its ICPU
block. Add a driver for it.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The Power Domain Controller (PDC) on QTI SoCs like SDM845 houses an
interrupt controller along with other domain control functions to handle
interrupt related functions like handle falling edge or active low which
are not detected at the GIC and handle wakeup interrupts.

The interrupt controller is on an always-on domain for the purpose of
waking up the processor. Only a subset of the processor's interrupts are
routed through the PDC to the GIC. The PDC powers on the processors'
domain, when in low power mode and replays pending interrupts so the GIC
may wake up the processor.
Signed-off-by: NArchana Sathyakumar <asathyak@codeaurora.org>
Signed-off-by: NLina Iyer <ilina@codeaurora.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Now that the fsl-mc bus core infrastructure is out of staging, the
remaining irqchip glue code used (irq-gic-v3-its-fsl-mc-msi.c) goes
to drivers/irqchip.

Create new Kconfig option for irqchip code that depends on
FSL_MC_BUS and ARM_GIC_V3_ITS. This ensures irqchip code only
gets built on ARM64 platforms. We can now remove #ifdef
GENERIC_MSI_DOMAIN_OPS as it was only needed for x86.
Signed-off-by: NStuart Yoder <stuyoder@gmail.com>
[rebased, add dpaa2_eth and dpio #include updates]
Signed-off-by: NLaurentiu Tudor <laurentiu.tudor@nxp.com>
[rebased, split irqchip to separate patch]
Signed-off-by: NBogdan Purcareata <bogdan.purcareata@nxp.com>
[add Kconfig dependency on ARM_GIC_V3_ITS]
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add device driver for a virtual programmable interrupt controller

The virtual PIC is designed as a device tree-based interrupt controller.

The compatible string used by OS for binding the driver is
"google,goldfish-pic".
Signed-off-by: NMiodrag Dinic <miodrag.dinic@mips.com>
Signed-off-by: NGoran Ferenc <goran.ferenc@mips.com>
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@mips.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The GICv3 ITS doesn't really depend on PCI. Only the PCI/MSI
part of it does, and there is no reason not to blow away most
of the irqchip stack because PCI is not selected (though not
selecting PCI seem to be asking for punishment, but hey...).

So let's split the PCI-specific part from the ITS in the Kconfig
file, and let's make that part depend on PCI. Architecture specific
hacks (arch/arm{,64}/Kconfig) will be addressed in a separate patch.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This patch adds GENERIC_IRQ_CHIP to stm32 exti
config.
Signed-off-by: NLudovic Barre <ludovic.barre@st.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

IPI driver for the Open Multi-Processor Interrupt Controller (ompic) as
described in the Multi-core support section of the OpenRISC 1.2
architecture specification:

  https://github.com/openrisc/doc/raw/master/openrisc-arch-1.2-rev0.pdf

Each OpenRISC core contains a full interrupt controller which is used in
the SMP architecture for interrupt balancing.  This IPI device, the
ompic, is the only external device required for enabling SMP on
OpenRISC.

Pending ops are stored in a memory bit mask which can allow multiple
pending operations to be set and serviced at a time. This is mostly
borrowed from the alpha IPI implementation.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NStefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: converted ops to bitmask, wrote commit message]
Signed-off-by: NStafford Horne <shorne@gmail.com>

The driver fails to compile with CONFIG_COMPILE_TEST=y on x86:

irq-meson-gpio.c: In function ‘meson_gpio_irq_parse_dt’:
irq-meson-gpio.c:343:8: error: implicit declaration of function
			       ‘of_property_read_variable_u32_array’
  ret = of_property_read_variable_u32_array(node,

Adding COMPILE_TEST to a driver requires at least compile testing it for
x86....
Reported-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>

Add support for the interrupt gpio controller found on Amlogic's meson
SoC family.

This controller is a separate controller from the gpio controller. It is
able to spy on the SoC pad. It is essentially a 256 to 8 router with a
filtering block to select level or edge and polarity. The number of actual
mappable inputs depends on the SoC.

Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Add a menu for IRQ chip drivers. This makes the Device drivers menu be more
consistent (listing "subsystems" instead of specific options) and makes the
IRQCHIP options be listed in expected places for 'make menu|xconfig'.
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/3db7385a-c6a1-5c93-0797-6f4b6b2b2cde@infradead.org

UniPhier SoCs contain AIDET (ARM Interrupt Detector).  This is intended
to provide additional features that are not covered by GIC.  The main
purpose is to provide logic inverter to support low level and falling
edge trigger types for interrupt lines from on-board devices.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The xtensa-mx driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-13-marc.zyngier@arm.com

The MIPS GIC driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-12-marc.zyngier@arm.com

The BCM 7038-L1 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-9-marc.zyngier@arm.com

The BCM 6345-L1 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-8-marc.zyngier@arm.com

The Armada 370 XP driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-7-marc.zyngier@arm.com

The GICv3 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-5-marc.zyngier@arm.com

The GIC driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-4-marc.zyngier@arm.com

The Marvell ICU unit is found in the CP110 block of the Marvell Armada
7K and 8K SoCs. It collects the wired interrupts of the devices located
in the CP110 and turns them into SPI interrupts in the GIC located in
the AP806 side of the SoC, by using a memory transaction.

Until now, the ICU was configured in a static fashion by the firmware,
and Linux was relying on this static configuration. By having Linux
configure the ICU, we are more flexible, and we can allocate dynamically
the GIC SPI interrupts only for devices that are actually in use.

The driver was initially written by Hanna Hawa <hannah@marvell.com>.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This commit adds a simple driver for the Marvell GICP, a hardware unit
that converts memory writes into GIC SPI interrupts. The driver provides
a number of functions to the ICU driver to allocate GICP interrupts, and
get the physical addresses that the ICUs should write to to set/clear
interrupts.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

ACPI IORT is an ACPI addendum to describe the connection topology of
devices with IOMMUs and interrupt controllers on ARM64 ACPI systems.

Currently the ACPI IORT Kbuild symbol is selected whenever the Kbuild
symbol ARM_GIC_V3_ITS is enabled, which in turn is selected by ARM64
Kbuild defaults. This makes the logic behind ACPI_IORT selection a bit
twisted and not easy to follow. On ARM64 systems enabling ACPI the
kbuild symbol ACPI_IORT should always be selected in that it is a kernel
layer provided to the ARM64 arch code to parse and enable ACPI firmware
bindings.

Make the ACPI_IORT selection explicit in ARM64 Kbuild and remove the
selection from ARM_GIC_V3_ITS entry, making the ACPI_IORT selection
logic clearer to follow.
Acked-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Introduce support for registering an IPI IRQ domain suitable for use by
systems using the MIPS MT (multithreading) ASE within a single core.
This will allow for such systems to be supported generically, without
the current kludge of IPI code split between the MIPS arch & the malta
board support code.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15836/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Gemini irqchip turns out to be a standard IP component from
Faraday Technology named FTINTC010 after some research and new
information.

- Rename the driver and all symbols to reflect the new information.
- Add the new compatible string "faraday,ftintc010"
- Create a Kconfig symbol CONFIG_FARADAY_FTINTC010 so that SoCs
  using this interrupt controller can easily select and reuse it
  instead of hardwiring it to ARCH_GEMINI

I have created a separate patch to select the new Kconfig symbol
from the Gemini machine, which will be merged through the ARM
SoC tree.

Cc: Greentime Hu <green.hu@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This driver uses the MSI domain but has no strict dependency on PCI_MSI, so we
may run into a build failure when CONFIG_GENERIC_MSI_IRQ_DOMAIN is disabled:

drivers/irqchip/irq-mvebu-odmi.c:152:15: error: variable 'odmi_msi_ops' has initializer but incomplete type
 static struct msi_domain_ops odmi_msi_ops = {
               ^~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:155:15: error: variable 'odmi_msi_domain_info' has initializer but incomplete type
 static struct msi_domain_info odmi_msi_domain_info = {
               ^~~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:3: error: 'struct msi_domain_info' has no member named 'flags'
  .flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS),
   ^~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:12: error: 'MSI_FLAG_USE_DEF_DOM_OPS' undeclared here (not in a function)
  .flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS),
            ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:39: error: 'MSI_FLAG_USE_DEF_CHIP_OPS' undeclared here (not in a function); did you mean 'MSI_FLAG_USE_DEF_DOM_OPS'?

Selecting the option from this driver seems to solve this nicely, though I could
not find any other instance of this in irqchip drivers.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Driver for interrupt combiners in the Top-level Control and Status
Registers (TCSR) hardware block in Qualcomm Technologies chips.

An interrupt combiner in this block combines a set of interrupts by
OR'ing the individual interrupt signals into a summary interrupt
signal routed to a parent interrupt controller, and provides read-
only, 32-bit registers to query the status of individual interrupts.
The status bit for IRQ n is bit (n % 32) within register (n / 32)
of the given combiner. Thus, each combiner can be described as a set
of register offsets and the number of IRQs managed.
Signed-off-by: NAgustin Vega-Frias <agustinv@codeaurora.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>