All the machines using the MMCI are passing GPIOs for the
card detect and write protect using the device tree or
descriptor table (one single case, Integrator/AP IM-PD1).

Drop support for passing global GPIO numbers through
platform data, noone is using it.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If hosts provides ops->adma_write_desc, we should not fall back to the
general sdhci_adma_write_desc().
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As you are already in ISR, it is unnecessary to call spin_lock_irqsave.
Signed-off-by: Njun qian <hangdianqj@163.com>
Reviewed-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size. The
size used is the result of a discussion with Renesas hardware engineers
and unfortunately not found in the datasheet.

  renesas_sdhi_internal_dmac ee140000.sd: DMA-API: mapping sg segment
  longer than device claims to support [len=126976] [max=65536]
Reported-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[wsa: simplified some logic after validating intended dma_parms life cycle
      and added comment]
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The eMMC controller is also a new timing mode controller, but it doesn't
have the timing mode switch. It does however have signal delay and
calibration controls, typical of Allwinner MMC controllers that support
the new timing mode.

Enable the new timing mode setting for the A64 eMMC controller. This
also enables MMC HS-DDR modes, which gives higher throughput for eMMC
chips that support it, and can deliver such throughput.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Newer sunxi mmc controller variants support what they call the "new
timing mode". Support for this was implemented in two ways, according
to the hardware that was seen at the time.

The first type retained the old timing mode, and both the clock and mmc
controllers had switches to select which mode was used. Both switches
had to be set to the same setting. This variant was denoted with the
.has_timings_switch field in the sunxi_mmc_cfg structure. This hardware
is only seen on the A83T.

The second type did away with the old timing mode. The clock controller
no longer had the mode selection or clock delay setting bits. In some
cases the mmc controller retained its mode selection bit, but this
always needed to be set to the new mode, or instabilities would occur.
In a few cases, such as the A64 and H6 eMMC controller, the mode
selection bit is gone, but the controller still behaves like the new
timing mode, requiring the module clock to be double the card clock
in DDR transfer modes. This variant is denoted with the
.needs_new_timings field.

This patch adds more comments explaining the two fields, as well as
the possibly nonexistent mode switch in the mmc controller.

The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify
its meaning.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.

R11 is a variant based on SD v4.0 specification.

With this driver, R11 mmc can be initialized, can be mounted, read and
written.
Original-by: NBillows Wu <billows.wu@unisoc.com>
Signed-off-by: NChunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds the device-tree binding documentation for Spreadtrum
SDHCI driver.
Signed-off-by: NChunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When Host Version 4 Enable is set to 1, SDMA uses ADMA System Address
register (05Fh-058h) instead of using register (000h-004h) to indicate
its system address of data location. The register (000h-004h) is
re-assigned to 32-bit Block Count and Auto CMD23 argument, so then SDMA
may use Auto CMD23.
Signed-off-by: NChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As SD Host Controller Specification v4.10 documents:
Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
Selection of Auto CMD depends on setting of CMD23 Enable in the Host
Control 2 register which indicates whether card supports CMD23. If CMD23
Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
recommended rather than use of Auto CMD12 Enable or Auto CMD23
Enable.

This patch add this new mode support.
Signed-off-by: NChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Host Controller Version 4.10 re-defines SDMA System Address register
as 32-bit Block Count for v4 mode, and SDMA uses ADMA System
Address register (05Fh-058h) instead if v4 mode is enabled. Also
when using 32-bit block count, 16-bit block count register need
to be set to zero.

Since using 32-bit Block Count would cause problems for auto-cmd23,
it can be chosen via host->quirk2.
Signed-off-by: NChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

ADMA2 64-bit addressing support is divided into V3 mode and V4 mode.
So there are two kinds of descriptors for ADMA2 64-bit addressing
i.e. 96-bit Descriptor for V3 mode, and 128-bit Descriptor for V4
mode. 128-bit Descriptor is aligned to 8-byte.

For V4 mode, ADMA2 64-bit addressing is enabled via Host Control 2
register.
Signed-off-by: NChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed conflict while applying]
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

According to the SD host controller specification version 4.10, when
Host Version 4 is enabled, SDMA uses ADMA System Address register
(05Fh-058h) instead of using SDMA System Address register to
support both 32-bit and 64-bit addressing.
Signed-off-by: NChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For SD host controller version 4.00 or later ones, there're two
modes of implementation - Version 3.00 compatible mode or
Version 4 mode.  This patch introduced an interface to enable
v4 mode.
Signed-off-by: NChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Added definitions for v400, v410, v420.
Signed-off-by: NChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix inconsistent IS_ERR and PTR_ERR in tegra_sdhci_init_pinctrl_info,
the proper pointer to be passed as argument is 'pinctrl_state_1v8'
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NAapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Rerun the pad calibration procedure before sdhci_request() if
the 100 ms recalibration interval has been exceeded.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Implement HS400 specific delay line calibration procedure. This is a
Tegra specific procedure and has to be performed regardless whether
enhanced strobe or HS400 tuning is used.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Implement eMMC HS400 enhanced strobe. Enhanced strobe is an alternative
mechanism to the HS400 tuning procedure.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Parse and program the HS400 DQS trim value from DT. Program a fallback
value in case the property is missing.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Document HS400 DQS trim value device tree property.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Set nvquirks to enable higher speed modes.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Set nvquirks to enable higher speed modes.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Implement tegra210_sdhci_writew() to disable card clock and issue a
reset when the tuning command is sent. This is done to prevent an
intermittent hang with around 10 % failure rate during tuning.

Add tegra186_sdhci_ops because this workaround is specific to Tegra210.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

tegra_sdhci_writew() defers the write to SDHCI_TRANSFER_MODE until
SDHCI_COMMAND is written. This is not necessary on Tegra210 and Tegra186
and it breaks read-modify-write operations on SDHCI_TRANSFER_MODE
because writes to SDHCI_TRANSFER_MODE aren't visible until SDHCI_COMMAND
has been written to. This results in tuning failures on Tegra210.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a new sdhci_ops struct for Tegra210 and Tegra186 which doesn't
set the custom tuning callback used on previous SoC generations.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Program the outbound sampling trim value in tegra_sdhci_reset(). Unlike
the outbound tap value this does not depend on the signaling mode and
needs to be only programmed once.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Set the default inbound timing adjustment tap value on reset and on
non-tunable modes.

The default tap value is not programmed on tunable modes because the
tuning sequence is used instead to determine the tap value.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Parse the default inbound and outbound sampling trimmer values from
the device tree.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add quirk to disable the card clock during configuration of the tap
value in tegra_sdhci_set_tap() and issue sdhci_reset() after value
change. This is a workaround to avoid propagation of a potential
glitch caused by setting the tap value.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Set NVQUIRK_HAS_PADCALIB on Tegra210 and Tegra186 to enable automatic
pad drive strength calibration.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Run the automatic pad calibration after voltage switching if
tegra_host->pad_calib_required is set.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Parse the pad drive strength calibration offsets from the device tree.
Program the calibration offsets in accordance with the current signaling
mode.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Disable the card clock during automatic pad drive strength calibration
and re-enable it afterwards.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Automatic pad drive strength calibration is performed on a separate pad
identical to the ones used for driving the actual bus. Power on the
calibration pad during the calibration procedure and power it off
afterwards to save power.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Reviewed-by: NMikko Perttunen <mperttunen@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Configure the voltage reference used by the automatic pad drive strength
calibration procedure. The value is a magic number from the TRM.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Implement polling with 10 ms timeout for automatic pad drive strength
calibration.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Parse the pinctrl state and nvidia,only-1-8-v properties from the device
tree. Validate the pinctrl and regulator configuration before unmasking
UHS modes. Implement pad voltage state reconfiguration in the mmc
start_signal_voltage_switch() callback. Add NVQUIRK_NEEDS_PAD_CONTROL
and add set it for Tegra210 and Tegra186.

The pad configuration is done in the mmc callback because the order of
pad reconfiguration and sdhci voltage switch depend on the voltage to
which the transition occurs.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Document the Tegra SDHCI inbound and outbound sampling trimmer values.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add bindings documentation for pad pull up and pull down offset values to be
programmed before executing automatic pad drive strength calibration.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>