Use unload to handle initialization failures instead of complex goto
label mess. To do this the initialization sequence needed slight
reordering and some unload functions needed to become conditional.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Stop using struct drm_driver load() and unload() callbacks. The
callbacks should not be used anymore. Instead of using load the
drm_device is allocated with drm_dev_alloc() and registered with
drm_dev_register() only after the driver is completely initialized.
The deinitialization is done directly either in component unbind
callback or in platform driver demove callback.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove obsolete drm_connector_register() calls from tilcdc_panel.c and
tilcdc_tfp410.c. All connectors are registered when drm_dev_register()
is called.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

This error message will be printed when a FIFO underflow irq has
triggered. Since this happens sometimes and the error message will be
displayed on the console, it should have a correct spelling.
Signed-off-by: NDaniel Schultz <d.schultz@phytec.de>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

The commit d8ff0c63fbcb ("drm/tilcdc: Adjust the FB_CEILING address")
added an adjustment of the FB_CEILING address. This is done by decrementing
the address by one.

On the AM335x (rev 0x4F201000) the framebuffer is rotated left over the
display border, because the ceiling address is 8f276fff instead of
8f277000. Since this adjustment isn't necessary for the LCDC v2, the
origin ceiling address should be used.
Signed-off-by: NDaniel Schultz <d.schultz@phytec.de>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Due to some potential tweaks for the da850 LCDC (for example: the
required memory bandwith settings) we need a separate compatible
for the IP present on the da850 boards.
Suggested-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Some architectures don't use the common clock framework and don't
implement all the clk interfaces for every clock. This is the case
for da850-lcdk where clk_set_rate() only works for PLL0 and PLL1.

Trying to set the clock rate for the LCDC clock results in -EINVAL
being returned.

As a workaround for that: if the call to clk_set_rate() fails, fall
back to adjusting the clock divider instead. Proper divider value is
calculated by dividing the current clock rate by the required pixel
clock rate in HZ.

This code is based on a hack initially developed internally for
baylibre by Karl Beldan <kbeldan@baylibre.com>.

Tested with a da850-lcdk with an LCD display connected over VGA.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

If we define drm_compat_ioctl NULL on CONFIG_COMPAT=n, we don't have to
check for the config everywhere.
Reviewed-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1478014844-27454-1-git-send-email-jani.nikula@intel.com

Convert DT component matching to use component_match_add_release().
Acked-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/E1bwo6l-0005Io-Q1@rmk-PC.armlinux.org.uk

The driver needs the number of bytes per pixel, not the bpp and depth
info meant for fbdev compatibility. Use the right API.

In the tilcdc_crtc_mode_set() function compute the hardware register
value directly from the pixel format instead of computing the number of
bits per pixels first.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1476744081-24485-7-git-send-email-laurent.pinchart@ideasonboard.com

drm_atomic_state has a complicated single owner model that tracks the
single reference from allocation through to destruction on another
thread - or perhaps on a local error path. We can simplify this tracking
by using reference counting (at a cost of a few more atomics). This is
even more beneficial when the lifetime of the state becomes more
convoluted than being passed to a single worker thread for the commit.

v2: Double check !intel atomic_commit functions for missing gets
v3: Update kerneldocs
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: NEric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161014121833.439-27-chris@chris-wilson.co.uk

When 'component_bind_all' fails it should not try to unbind components
in the error handling. This will produce a null pointer kernel panic when
no component exist.

This patch changes the order of the error handling. Now, it will only
unbind components if the are bound. Otherwise, the module will jump to
an error label below.
Signed-off-by: NDaniel Schultz <d.schultz@phytec.de>
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Return directly after a memory allocation failed in this function
at the beginning.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Fixes the following sparse warning:

drivers/gpu/drm/tilcdc/tilcdc_drv.c:64:5: warning:
 symbol 'tilcdc_atomic_check' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

We get 3 warnings when building kernel with W=1:
drivers/gpu/drm/tilcdc/tilcdc_slave_compat.c:142:29: warning: no previous prototype for 'tilcdc_get_overlay' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_slave_compat.c:198:13: warning: no previous prototype for 'tilcdc_convert_slave_node' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_slave_compat.c:264:12: warning: no previous prototype for 'tilcdc_slave_compat_init' [-Wmissing-prototypes]

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

We get 4 warnings when building kernel with W=1:
drivers/gpu/drm/tilcdc/tilcdc_tfp410.c:393:12: warning: no previous prototype for 'tilcdc_tfp410_init' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_tfp410.c:398:13: warning: no previous prototype for 'tilcdc_tfp410_fini' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_panel.c:443:12: warning: no previous prototype for 'tilcdc_panel_init' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_panel.c:448:13: warning: no previous prototype for 'tilcdc_panel_fini' [-Wmissing-prototypes]

In fact, these functions are declared in
drivers/gpu/drm/tilcdc/tilcdc_tfp410.h,
drivers/gpu/drm/tilcdc/tilcdc_panel.h,
so this patch adds missing header dependencies.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Also reorder alphabetically and fix up drm_flip_work header.
Reviewed-by: NDaniel Vetter <daniel@ffwll.ch>
Signed-off-by: NSean Paul <seanpaul@chromium.org>

WARN if CRTC is touched without CRTC lock. The crtc functions should
not be called simultaneously from multiple threads. Having the DRM
CRTC lock should take care of that.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Take CRTC lock when calling tilcdc_crtc_disable() in
tilcdc_crtc_destroy().

In theory there could still be some operation ongoing, which should
finish before destroying the CRTC. However, the main reason for
adding this is to be able to add WARNing in tilcdc_crtc_disable() if
CRTC is not locked.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove unnecessary tilcdc_crtc_disable() from tilcdc_unload(). The
tilcdc_crtc_disable() called via tilcdc_crtc_destroy() by
drm_mode_config_cleanup() couple of lines later.

The early call to tilcdc_crtc_disable() was a wrong fix (that worked)
for calling drm_flip_work_cleanup() before flushing the flip-work
queue.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Flush flip-work workqueue before drm_flip_work_cleanup(). It causes a
nasty warning if there is unfinished flip-work in the queue when
drm_flip_work_cleanup() is called. The flush_workqueue() has to be
called before drm_crtc_cleanup() for unref_worker() to be able to do
its job.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Clean up LCDC functional clock rate setting code.

The LCDC functional clock is set by two functions: mode_set_nofb() and
cpufreq_transition().

When tilcdc_crtc_mode_set_nofb() is called in atomic commit phase the
drm atomic helpers have taken all the necessary drm locks and turned
off the crtc, while tilcdc_commit() is keeping LCDC powered on. For
mode_set_nofb() just a simple clock setting function without any
locking or power management code is enough. The new tilcdc_crtc_set_clk()
is implemented for that purpose.

cpufreq_transition() on the other hand is called from outside DRM and
it needs to take the necessary locks and turn off the CRTC while
keeping the LCDC powered. The reimplemented tilcdc_crtc_update_clk()
is for that purpose and it uses the new tilcdc_crtc_set_clk() to
actually set the clock.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Take crtc modeset lock while updating the crtc clock rate. To avoid a
race in tilcdc_crtc_update_clk(), we do not want crtc mode to change
while we update crtc clock.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Choose console BPP that supports RGB and remove the old fbdev bpp
selection code. LCDC on AM335x has red and blue wires switched between
24 bit and 16 bit colors. If 24 format is wired for RGB colors, the 16
bit format is wired for BGR. drm_fbdev_cma_init() does not currently
like anything else but RGB formats, so we must choose such bytes per
pixel value that supports RGB.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add "blue-and-red-wiring"-device tree property and update devicetree
binding document.

The red and blue components are reversed between 24 and 16 bit modes
on am335x LCDC output pins. To get 24 RGB format the red and blue
wires has to be crossed and this in turn causes 16 colors output to be
in BGR format. With straight wiring the 16 color is RGB and 24 bit is
BGR.

The new property describes whether the red and blue wires are crossed
or not. If the property is not present or its value is not recognized
the legacy mode is assumed. The legacy configuration supports RGB565,
RGB888 and XRGB8888 formats. However, depending on wiring, the red and
blue colors are swapped in either 16 or 24-bit color modes.

For more details see section 3.1.1 in AM335x Silicon Errata:
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Write DMA base and ceiling address with a single instruction, if
available. This should make it more unlikely that LCDC would fetch the
DMA addresses in the middle of an update. Having bad combination of
addresses in dma base and ceiling (e.g base > ceiling) can cause
unpredictaple behavior in LCDC.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

drm_helper_disable_unused_functions() should not be called by atomic
drivers.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This got accidentally dropped in the fixed commit and is required for
the driver to properly work on the rev1 IP, such as found on the LCDK.

Fixes: 2b2080d7 ("drm/tilcdc: Get rid of complex ping-pong mechanism")
Signed-off-by: NKarl Beldan <kbeldan@baylibre.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

The LCDC seems to expect its framebuffer ceiling address pointer to be
an inclusive bound.  The IP rev2 seems to cope with that but rev1 (as
found on the LCDK) don't.
Also note that this is what the framebuffer code does in da8xx-fb.c.

Since, as the TRM puts it, "The 2 LSBs are hardwired to 00b", the
dma_addr_t can be decremented without cast.
I tested it with a v2 (AM335x, rev  0x4F201000) and an LCDK (v1).
Signed-off-by: NKarl Beldan <kbeldan@baylibre.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

In function tilcdc_get_external_components the check for
the remote port parent is not correct. We need a '||' instead of
an '&&'.
Signed-off-by: NTeresa Remmet <t.remmet@phytec.de>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: NLiu Ying <gnuiyl@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com

Change tilcdc_crtc_page_flip() to tilcdc_crtc_update_fb(). The
function is not used as a page_flip() callback anymore so it is only
confusing to call it that. The function should only be used by dummy
primary plane commit() callback.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Remove unnecessary pm_runtime_get() and *_put() calls from commit
phase callbacks. Those calls are not needed since we have the whole
commit phase between pm_runtime_get_sync() and pm_runtime_put_sync().
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Get rid of legacy dpms mechanism. This simplifies the code quite a
bit. The old start() and stop() functions become tilcdc_crtc_enable()
and *_disable(). The functions are added with all the necessary
mechanisms from the old dpms function and they are used directly as
the crtc helper enable() and disable() callbacks.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Use drm_atomic_helper_resume/suspend() and get rid off all the obsolete
register level context restoring code.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Enable and disable interrupts in crtc start() and stop(). None of the
interrupts can fire if CRTC is disabled, so it is cleaner - when
considering suspend/resume code etc. - to enable the interrupts when
CRTC is turned on and to disable them when CRTC is turned off.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Add atomic modeset helpers to tfp410 connector funcs. Property handling
related helpers, atomic reset helper, and new dpms helper is needed in
connector for atomic modeseting to work. The default helper functions
are enough.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Set crtc panel info at init phase. Setting it at prepare callback does
it multiple times for no good reason and it is also too late when atomic
modeset is used.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Add atomic modeset helpers to panel connector funcs. Property handling
related helpers, atomic reset helper, and new dpms helper is needed in
connector for atomic modeseting to work. The default helper functions
are enough.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Set crtc panel info at init phase. Setting it at prepare callback does
it multiple times for no good reason and it is also too late when atomic
modeset is used.
Signed-off-by: NJyri Sarha <jsarha@ti.com>