Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 17 11月, 2011 1 次提交
    • C
      KVM: s390: Fix RUNNING flag misinterpretation · 9e6dabef
      由 Cornelia Huck 提交于 
      CPUSTAT_RUNNING was implemented signifying that a vcpu is not stopped.
This is not, however, what the architecture says: RUNNING should be
set when the host is acting on the behalf of the guest operating
system.

CPUSTAT_RUNNING has been changed to be set in kvm_arch_vcpu_load()
and to be unset in kvm_arch_vcpu_put().

For signifying stopped state of a vcpu, a host-controlled bit has
been used and is set/unset basically on the reverse as the old
CPUSTAT_RUNNING bit (including pushing it down into stop handling
proper in handle_stop()).

Cc: stable@kernel.org
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>
      9e6dabef
  3. 12 11月, 2011 3 次提交
  5. 11 11月, 2011 4 次提交
  7. 10 11月, 2011 3 次提交
    • Y
      arm/tegra: enable headphone detection gpio on seaboard · 686448d7
      由 Yufeng Shen 提交于 
      Enable the headphone detection gpio on tegra platform.
Signed-off-by: NYufeng Shen <miletus@chromium.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>
      686448d7
    • S
      arm/dt: Fix ventana SDHCI power-gpios · c406eeb3
      由 Stephen Warren 提交于 
      Ventana uses the same SDHCI GPIOs as Seaboard; PI6 (70) is the power GPIO
for the SD port, and there is no power GPIO for the MMC chip.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>
      c406eeb3
    • S
      arm/tegra: Don't create duplicate gpio and pinmux devices · 4b91b6fb
      由 Stephen Warren 提交于 
      *_pinmux_init() register the GPIO and pinmux devices so that they're ready
before any other device needs them.

*_pinmux_init() are also called by board-dt.c in order to set up the GPIO
and pinmux configurations. In this case, if we register the devices, they
end up being probed once due to this registration, and a second time due
to a device-tree node (or vice-versa). The second probe fails since the
memory regions are already requested. Besides, we don't actually want the
duplicated devices.

To avoid this duplicate registration, modify *_pinmux_init() to check
whether it's running on a DT machine. If not, register the pinmux devices.
If so, don't register them.

Finally, modify board-dt.c to call the *_pinmux_init() after all devices have
been instantiated from device-tree. This allows the GPIO and pinmux devices
to be instantiated and initialized before calling functions to configure the
hardware.

This has one disadvantage: The pinmux and GPIO initialization now happens
after /all/ devices are instantiated, rather than after just gpio and
pinmux but before anything else. So the correct HW configuration is not
in place when e.g. the SD/MMC device is probed. Long-term, this should be
solved by doing both:

a) Initializing the HW state from DT nodes during GPIO and pinmux device
   probe.
b) Using the deferred driver probe mechanism, so that drivers can defer
   their probe until after the gpio and pinmux drivers have probed.

v2: s/int is_dt/bool is_dt/
v3: Use of_machine_is_compatible inside *_pinmux_init() rather than passing
an explicit parameter into the function from outside.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>
      4b91b6fb
  9. 09 11月, 2011 29 次提交