Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 04 10月, 2018 1 次提交
    • F
      net/mlx5: Add Fast teardown support · fcd29ad1
      由 Feras Daoud 提交于 
      Today mlx5 devices support two teardown modes:
1- Regular teardown
2- Force teardown

This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the pages.

Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Reviewed-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
      fcd29ad1
  3. 09 8月, 2018 1 次提交
  5. 24 7月, 2018 1 次提交
    • F
      net/mlx5: FW tracer, events handling · c71ad41c
      由 Feras Daoud 提交于 
      The tracer has one event, event 0x26, with two subtypes:
- Subtype 0: Ownership change
- Subtype 1: Traces available

An ownership change occurs in the following cases:
1- Owner releases his ownership, in this case, an event will be
sent to inform others to reattempt acquire ownership.
2- Ownership was taken by a higher priority tool, in this case
the owner should understand that it lost ownership, and go through
tear down flow.

The second subtype indicates that there are traces in the trace buffer,
in this case, the driver polls the tracer buffer for new traces, parse
them and prepares the messages for printing.

The HW starts tracing from the first address in the tracer buffer.
Driver receives an event notifying that new trace block exists.
HW posts a timestamp event at the last 8B of every 256B block.
Comparing the timestamp to the last handled timestamp would indicate
that this is a new trace block. Once the new timestamp is detected,
the entire block is considered valid.

Block validation and parsing, should be done after copying the current
block to a different location, in order to avoid block overwritten
during processing.
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
      c71ad41c
  7. 19 7月, 2018 1 次提交
  9. 20 6月, 2018 1 次提交
  11. 01 6月, 2018 2 次提交
  13. 25 5月, 2018 1 次提交
  15. 17 5月, 2018 2 次提交
  17. 06 4月, 2018 1 次提交
  19. 31 3月, 2018 1 次提交
    • T
      net/mlx5e: Use linear SKB in Striding RQ · 619a8f2a
      由 Tariq Toukan 提交于 
      Current Striding RQ HW feature utilizes the RX buffers so that
there is no wasted room between the strides. This maximises
the memory utilization.
This prevents the use of build_skb() (which requires headroom
and tailroom), and demands to memcpy the packets headers into
the skb linear part.

In this patch, whenever a set of conditions holds, we apply
an RQ configuration that allows combining the use of linear SKB
on top of a Striding RQ.

To use build_skb() with Striding RQ, the following must hold:
1. packet does not cross a page boundary.
2. there is enough headroom and tailroom surrounding the packet.

We can satisfy 1 and 2 by configuring:
	stride size = MTU + headroom + tailoom.

This is possible only when:
a. (MTU - headroom - tailoom) does not exceed PAGE_SIZE.
b. HW LRO is turned off.

Using linear SKB has many advantages:
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
  small amount (linear part) and large amount (fragment).
  This saves datapath cycles in driver and improves utilization
  of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
  assumption of equal-size fragments.

Some implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.

This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.

Performance testing:
ConnectX-5, single core, single RX ring, default MTU.

UDP packet rate, early drop in TC layer:

--------------------------------------------
| pkt size | before    | after     | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
|  500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
|   64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------

TCP streams: ~20% gain
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
      619a8f2a
  21. 27 3月, 2018 1 次提交
    • I
      net/mlx5e: Expose PFC stall prevention counters · 2fcb12df
      由 Inbar Karmy 提交于 
      Add the needed capability bit and counters to device spec description.
Expose the following two counters in ethtool:

tx_pause_storm_warning_events: when the device is stalled for a period
longer than a pre-configured watermark, the counter increase, allowing
the debug utility an insight into current device status.

tx_pause_storm_error_events: when the device is stalled for a period
longer than a pre-configured timeout, the pause transmission is disabled,
and the counter increase.
Signed-off-by: NInbar Karmy <inbark@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
      2fcb12df
  23. 15 3月, 2018 1 次提交
  25. 09 1月, 2018 2 次提交
  27. 29 12月, 2017 1 次提交
    • Y
      IB/mlx5: Extend UAR stuff to support dynamic allocation · 31a78a5a
      由 Yishai Hadas 提交于 
      This patch extends the alloc context flow to be prepared for working
with dynamic UAR allocations.

Currently upon alloc context there is some fix size of UARs that are
allocated (named 'static allocation') and there is no option to user
application to ask for more or control which UAR will be used by which
QP.

In this patch the driver prepares its data structures to manage both the
static and the dynamic allocations and let the user driver knows about
the max value of dynamic blue-flame registers that are allowed.

Downstream patches from this series will enable the dynamic allocation
and the association as part of QP creation.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
      31a78a5a
  29. 05 11月, 2017 2 次提交
  31. 28 9月, 2017 1 次提交
  33. 03 9月, 2017 1 次提交
  35. 24 8月, 2017 1 次提交
  37. 24 7月, 2017 2 次提交
  39. 27 6月, 2017 1 次提交
    • I
      net/mlx5: FPGA, Add SBU infrastructure · a9956d35
      由 Ilan Tayari 提交于 
      Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.

A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.

Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.

At high level, the FPGA configuration space is divided such:
 0x00000000 - 0x007fffff is reserved for the SBU
 0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ...        is DDR memory

A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
      a9956d35
  41. 22 6月, 2017 1 次提交
  43. 23 5月, 2017 1 次提交
  45. 14 5月, 2017 1 次提交
    • I
      net/mlx5: FPGA, Add basic support for Innova · e29341fb
      由 Ilan Tayari 提交于 
      Mellanox Innova is a NIC with ConnectX and an FPGA on the same
board. The FPGA is a bump-on-the-wire and thus affects operation of
the mlx5_core driver on the ConnectX ASIC.

Add basic support for Innova in mlx5_core.

This allows using the Innova card as a regular NIC, by detecting
the FPGA capability bit, and verifying its load state before
initializing ConnectX interfaces.

Also detect FPGA fatal runtime failures and enter error state if
they ever happen.

All new FPGA-related logic is placed in its own subdirectory 'fpga',
which may be built by selecting CONFIG_MLX5_FPGA.
This prepares for further support of various Innova features in later
patchsets.
Additional details about hardware architecture will be provided as
more features get submitted.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Reviewed-by: NBoris Pismenny <borisp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
      e29341fb
  47. 06 2月, 2017 1 次提交
  49. 20 1月, 2017 6 次提交
  51. 10 1月, 2017 1 次提交
    • E
      IB/mlx5: Allow future extension of libmlx5 input data · b037c29a
      由 Eli Cohen 提交于 
      Current check requests that new fields in struct
mlx5_ib_alloc_ucontext_req_v2 that are not known to the driver be zero.
This was introduced so new libraries passing additional information to
the kernel through struct mlx5_ib_alloc_ucontext_req_v2 will be notified
by old kernels that do not support their request by failing the
operation. This schecme is problematic since it requires libmlx5 to issue
the requests with descending input size for struct
mlx5_ib_alloc_ucontext_req_v2.

To avoid this, we require that new features that will obey the following
rules:
If the feature requires one or more fields in the response and the at
least one of the fields can be encoded such that a zero value means the
kernel ignored the request then this field will provide the indication
to the library. If no response is required or if zero is a valid
response, a new field should be added that indicates to the library
whether its request was processed.

Fixes: b368d7cb ('IB/mlx5: Add hca_core_clock_offset to udata in init_ucontext')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
      b037c29a
  53. 08 1月, 2017 2 次提交
  55. 03 1月, 2017 1 次提交
  57. 29 12月, 2016 1 次提交