The Wacom Pro Pen 3D includes a third barrel switch which is intended to
be particularly useful in applications where one frequency uses pan, zoom,
and rotate to navigate around a scene or model. The pen is compatible with
the MobileStudio Pro, 2nd-gen Intuos Pro, and Cintiq Pro. When the third
button is pressed, these devices set both the HID_DG_BARRELSWITCH and
HID_DG_BARRELSWITCH2 usages since their HID descriptors do not include a
usage specific to the button.

Rather than send both BTN_STYLUS and BTN_STYLUS2 when the third button is
pressed, userspace (libinput) has requested that we detect this condition
and report a newly-defined BTN_STYLUS3 event instead. We could define a
quirk specific to devices compatible with the Pro Pen 3D, but the liklihood
of seeing both barrel switch bits set with other pens/devices is low enough
to not worry about (pens mechanically prevent accidental activation of
multiple switches).
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: NPeter Hutterer <peter.hutterer@who-t.net>
Acked-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This reverts commit 3e70969e.

This commit causes a few problems for userspace. The most noteworthy are
problems related to the distinguishing of different pens and pointer jumps
when entering proximity. Userspace is written with the expectation that a
pen will provide its tool ID and serial number (if available) in the very
first in-prox report. By sending BTN_TOOL_PEN when the tablet starts
communicating rather than waiting until a tool ID/serial number is
available, userspace ends up treating all pens as being the same and
lacking a serial number. Similarly, userspace assumes that the first
report will contain X/Y data, but by marking the pen as being in-prox
without an X/Y coordinate, userspace ends up warping the pen to the last-
known X/Y location. As of commit 5b40104e ("HID: wacom: generic: Reset
events back to zero when pen leaves") this means warping to (0,0).
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Acked-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

As a pen leaves, we need to be sure to reset all events back to zero
so that userspace is able to get the complete pen state when it enters
proximity again.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When a pen is first able to to be sensed by the tablet, we would like
to inform userspace that a tool is nearby so that it can attempt to
perform palm rejection. Unfortunately, we don't know any information
about the tool that is nearby, so the best we can do is send a prox
event for a generic BTN_TOOL_PEN. If the pen later comes closer and
enters proximity, we can determine the actual tool type and send
BTN_TOOL_PEN out of prox if necessary.
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The legacy Intuos codepath and tablet behavior (e.g. the 1st-gen Intuos
Pro, Cintiq 27, etc.) would result in a BTN_TOOL_* event not being cleared
to zero until the tool had completely left the sensing range of the
tablet. Before the final "out of prox" packet would be sent, zero or
more "in range" packets could be sent to indicate that a pen was still
detectable but not within a useful distance. These "in range" packets
were used by the driver to keep touch input disabled at greater pen
distances. In addition to keeping the `stylus_in_proximity` flag set,
the driver would leave the current BTN_TOOL_* marked as being in
proximity as well.

The new HID codepath also sets `stylus_in_proximity` based on the "sense"
flag, but does not leave the current BTN_TOOL_* marked as being in prox.
This information is potentially useful to for a future userspace-based
palm rejection, so this patch modifies the driver to continue sending it.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The terminology used to describe the various degrees of pen proximity
within the wacom_wac_pen_report function does not match that used elsewhere
in the generic codepath. Specifically, the names of the variables "prox"
and "range" were inspired by the non-generic codepaths. To make the generic
codepath internally consistent, replace these terms with "range" and "sense"
respectively.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The tool ID information sent in ABS_MISC is expected to be reset to 0
when a tool leaves proximity. Not doing this can cause problems if a
tool is removed and then re-introduced. Kernel event filtering will
prevent the (identical) ABS_MISC event from being sent when the tool
re-enters proxmity. This can cause userspace to not properly set the
tool ID.

Fixes: f85c9dc6 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable # v4.10 <stable@vger.kernel.org>
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The latest generation of pro devices (MobileStudio Pro, 2nd-gen Intuos
Pro, Cintiq Pro) send a serial number of '0' whenever the pen is too far
away for reliable communication. Userspace defines that a serial number
of '0' is invalid, so we need to be careful not to actually forward
this value. Additionally, since EMR ISDv4 devices do not support serial
numbers or tool IDs, we'd like to not send these events if they aren't
necessary.

The existing code achieves these goals by adding a check for a non-zero
serial number within the wacom_wac_pen_report function. The MSC_SERIAL
and ABS_MISC events are only sent if the serial number is non-zero. This
code fails, however when the pen for a pro device leaves proximity. When
the pen leaves prox and the tablet sends a serial of 0, wacom_wac_pen_event
dutifully clears the serial number. When wacom_wac_pen_report is called,
it does not send either the MSC_SERIAL of the exiting tool nor an ABS_MISC
event.

This patch prevents the wacom_wac_pen_event function from clearing an
already-set serial number. This ensures that we have the serial number
handy when exiting proximity, but requires us to manually clear it
afterwards to ensure the driver does not send stale data (e.g. when
switching between AES pens that report a serial nubmer of 0 for the
first few fully in-proximity packets).

Fixes: f85c9dc6 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable # v4.10 <stable@vger.kernel.org>
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The MobileStudio Pro, Cintiq Pro, and 2nd-gen Intuos Pro devices use a
different coordinate system for their touchring and pen twist than prior
devices. Prior devices had zero aligned to the tablet's left and would
increase clockwise. Userspace expects data from the kernel to be in this
old coordinate space, so adjustments are necessary.

While the coordinate system for pen twist is formally defined by the HID
standard, no such definition existed for the touchring at the time these
tablets were introduced. Future tablets are expected to report touchring
data using the same "zero-up clockwise-increasing" coordinate system
defined for twist.

Fixes: 50066a04 ("HID: wacom: generic: Add support for height, tilt, and twist usages")
Fixes: 4922cd26 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Fixes: 60a22186 ("HID: wacom: generic: add support for touchring")
Cc: stable@vger.kernel.org # 4.10, 4.11
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The wacom driver's IRQ handler for Bluetooth reports from the 2nd-gen
Intuos Pro does not correctly process negative numbers. Values for
tilt and rotation (which can go negative) are instead interpreted as
unsigned and so jump to very large values when the data should be
negative. This commit properly casts the data to ensure we report
negative numbers when necessary.

Fixes: 4922cd26 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: stable@vger.kernel.org # v4.11
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Cintiq 12 has 10 expresskey buttons. The bit shift for the last
two buttons were off by 5.

Fixes: c7f0522a ("HID: wacom: Slim down wacom_intuos_pad processing")
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Tested-by: NMatthieu Robin <matthieu@macolu.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The WACOM_HID_WD_TOUCHRINGSTATUS usage is a single bit which tells us
whether the touchring is currently in use or not. Because we need to
reset the axis value to 0 when the finger is removed, we call
'wacom_map_usage' to ensure that the required type/code values are
associated with the usage. The 'wacom_map_usage' also sets up the axis
range and resolution, however, which is not desired in this particular
case.

Although xf86-input-wacom doesn't do really do anything with the ring's
range or resolution, the libinput driver (for Wayland environments)
uses these values to provide proper angle indications to userspace.

Fixes: 60a22186 ("HID: wacom: generic: add support for touchring")
Cc: stable@vger.kernel.org
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

trivial fix to spelling mistake in hid_warn warning message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Generic battery handling code is spread between the pen and pad codepaths
since battery usages may appear in reports for either. This makes it
difficult to concisely see the logic involved. Since battery data is
not treated like other data (i.e., we report it through the power_supply
subsystem rather than through the input subsystem), it makes reasonable
sense to split the functionality out into its own functions.

This commit has the generic battery handling duplicate the same pattern
that is used by the pen, pad, and touch interfaces. A "mapping" function
is provided to set up the battery, an "event" function is provided to
update the battery data, and a "report" function is provided to notify
the power_supply subsystem after all the data has been read. We look at
the usage itself rather than its collection to determine if one of the
battery functions should handle it. Additionally, we unconditionally
call the "report" function since there is no particularly good way to
know if a report contained a battery usage; 'wacom_notify_battery()'
will filter out any duplicate updates, however.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

At the moment, our driver relies on 'wacom_battery_get_property()' to
determine the most likely battery state (e.g charging, discharging, or
full) based on the information available. It is not always possible
for the function to properly determine this, however. For instance,
whenever an AES pen leaves proximity the battery state becomes
indeterminite. This commit adds the ability to provide it with explict
state information if desired. Whenever explicit state is not required
(the majority of circumstances), WACOM_POWER_SUPPLY_STATUS_AUTO can
be used in its place.

Three uses of explicit battery status are added: two wireless disconnect
paths and the AES case mentioned above.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When support for the HID_DG_BATTERYSTRENGTH usage was added for AES devices,
it appears that the value was read, but never actually forwarded to the
power_supply subystem for userspace's benefit. Let's correct that.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

AES sensors use the value 0 to indicate "not available" rather than
"completely dead". Such values are often sent for dozens of reports
while the pen is being brought into proximity and can cause userspace
to get the wrong impression about the actual battery state.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The power_supply subsystem expects us to provide it with capacity values
measured in percent. In particular, AES devices (HID_DG_BATTERYSTRENGTH)
use the range 0-255, which needs to be rescaled. The MobileStudio Pro
(WACOM_HID_WD_BATTERY_LEVEL) uses the range 0-100, but there's no guarantee
that future devices will share the same range.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The following Smatch complaint was generated in response to commit
2a6cdbdd ("HID: wacom: Introduce new 'touch_input' device"):

    drivers/hid/wacom_wac.c:1586 wacom_tpc_irq()
             error: we previously assumed 'wacom->touch_input' could be null (see line 1577)

The 'touch_input' and 'pen_input' variables point to the 'struct input_dev'
used for relaying touch and pen events to userspace, respectively. If a
device does not have a touch interface or pen interface, the associated
input variable is NULL. The 'wacom_tpc_irq()' function is responsible for
forwarding input reports to a more-specific IRQ handler function. An
unknown report could theoretically be mistaken as e.g. a touch report
on a device which does not have a touch interface. This can be prevented
by only calling the pen/touch functions are called when the pen/touch
pointers are valid.

Fixes: 2a6cdbdd ("HID: wacom: Introduce new 'touch_input' device")
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

It apears that devices designed around Wacom's G11 chipset (e.g. Lenovo
ThinkPad Yoga 260, Lenovo ThinkPad X1 Yoga, Dell XPS 12 9250, Dell Venue
8 Pro 5855, etc.) suffer from a common issue in their HID descriptors.
The logical maximum is not updated for the "Contact Identifier" usage,
leaving it as just "1" despite these devices being capable of tracking
far more touches.

Commit 60a22186 began ignoring usages with out-of-range values,
causing problems for devices based on this chipset. Touches after
the first will have an out-of-range Contact Identifier, and ignoring
that usage will cause the kernel to incorrectly slot each finger's
events (along with all the knock-on userspace effects that entails).

This commit checks for these buggy descriptors and updates the maximum
where required. Prior chipsets have used "255" as the maximum (and the
G11, at least, doesn't seem to actually use IDs outside the range of
1..CONTACTMAX) so continue using this value.

Cc: stable@vger.kernel.org
Fixes: 60a22186 ("HID: wacom: generic: add support for touchring")
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Because HID_DG_TOOLSERIALNUMBER doesn't first cast the value recieved from HID
to an unsigned type, sign-extension rules can cause the value of
wacom_wac->serial[0] to inadvertently wind up with all 32 of its highest bits
set if the highest bit of "value" was set.

This can cause problems for Tablet PC devices which use AES sensors and the
xf86-input-wacom userspace driver. It is not uncommon for AES sensors to send a
serial number of '0' while the pen is entering or leaving proximity. The
xf86-input-wacom driver ignores events with a serial number of '0' since it
cannot match them up to an in-use tool.  To ensure the xf86-input-wacom driver
does not ignore the final out-of-proximity event, the kernel does not send
MSC_SERIAL events when the value of wacom_wac->serial[0] is '0'. If the highest
bit of HID_DG_TOOLSERIALNUMBER is set by an in-prox pen which later leaves
proximity and sends a '0' for HID_DG_TOOLSERIALNUMBER, then only the lowest 32
bits of wacom_wac->serial[0] are actually cleared, causing the kernel to send
an MSC_SERIAL event. Since the 'input_event' function takes an 'int' as
argument, only those lowest (now-cleared) 32 bits of wacom_wac->serial[0] are
sent to userspace, causing xf86-input-wacom to ignore the event. If the event
was the final out-of-prox event, then xf86-input-wacom may remain in a state
where it believes the pen is in proximity and refuses to allow other devices
under its control (e.g. the touchscreen) to move the cursor.

It should be noted that EMR devices and devices which use both the
HID_DG_TOOLSERIALNUMBER and WACOM_HID_WD_SERIALHI usages (in that order) would
be immune to this issue. It appears only AES devices are affected.

Fixes: f85c9dc6 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable@vger.kernel.org
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Acked-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

These two functions awkwardly break up the otherwise-contiguous chunk of
related Intuos IRQ functions with a 500 line tangent about the operation
of the EKR. Their presence makes it difficult to read/navigate through the
the Intuos code. Since there is no dependency between these functions, it
is possible to simply move them down somewhat. This commit moves them
to be after the final Intuos IRQ function.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commits d793ff81 and 4082da80 introduced two pad usages which do not
actually send pad input events. To make sure we do not post empty
pad packets, pad_input_event_flag is introduced. Turn on the flag
for real pad input events so we can synchronize them properly.
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit 3b164a00 ("HID: wacom: Cleanup unsupported device_type
for BAMBOO_PT") cleaned up Bamboo devices which our driver falsely
claimed had touch. Bamboo One Medium also does not have touch.
Signed-off-by: NAaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit f85c9dc6 ("Support tool ID and additional tool types") introduced mouse
and lens cursor tools to generic codepath, which covers both display (direct)
and opaque tablets (indirect devices). However, mouse and lens cursor tools are
only provided for opaque tablets. This patch ignores mouse and lens cursor tools
if the device is a display tablet.
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Reviewed-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The features struct for the second gen Intuos Pro uses the wrong constant for
the resolution. This fix is for commit 4922cd26.

Fixes: 4922cd26 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Signed-off-by: NAaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Wacom Cintiq Pro has a softkey to turn touch on/off. Since it is
a softkey, hardware/firmware still reports touch events no matter
what state the softkey is. We need to ignore touch events when
the key is in off mode.
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: NAaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Wacom Cintiq Pro added a touch key to switch the tablet between
display and opaque mode. This patch informs the change by removing
the old devices and creating new ones with proper properties.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Tested-by: NAaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch add support to the 3 touch keys on Wacom Cintiq Pro.  These touch
keys are in the middle of the other two keys on the top edge of the tablet.
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: NAaron Armstrong Skomra <aaron.skomra@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The prox/range bits included in the Bluetooth reports from the Intuos Pro
were being ignored, leading to two issues. Firstly, the pen would never
announce a BTN_TOOL_PEN event with value 0, leaving userspace to believe
the pen was always active. Secondly, the driver would continue to send
events for data while the packet's "prox" bit was clear. This can lead
to sudden incorrect pointer jumps if the pen is slowly moved away from
the tablet surface.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <ping.cheng@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Non-generic devices have numbered_buttons set for both pen and
touch interfaces by default. The actual number of buttons on the
interface is normally manually decided later, which is different
from what those HID generic devices are processed, where number
of buttons are directly retrieved from HID descriptors.

This patch adds the missed HID_GENERIC check and moves the statement
to wacom_setup_pad_input_capabilities since it's not a quirk anymore.
Signed-off-by: NPing Cheng <ping.cheng@wacom.com>
Reviewed-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit 025bcc15 performed cleanup work on the 'wacom_pl_irq' function, making
it follow the standards used in the rest of the codebase. The change
unintiontionally allowed the function to send input events from reports
that are not marked as being in prox. This can cause problems as the
report values for X, Y, etc. are not guaranteed to be correct. In
particular, occasionally the tablet will send a report with these values
set to zero. If such a report is received it can caus an unexpected jump
in the XY position.

This patch surrounds more of the processing code with a proximity check,
preventing these zeroed reports from overwriting the current state. To
be safe, only the tool type and ABS_MISC events should be reported when
the pen is marked as being out of prox.

Fixes: 025bcc15 ("HID: wacom: Simplify 'wacom_pl_irq'")
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add support for the LEDs around the mode switch to the generic code path in
support of the second generation Intuos Pro.
Signed-off-by: NAaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The second generation Intuos Pro is the first device in the generic codepath
which has a touchswitch. We utilize a flag in wacom_shared in order to report
this switch event received from the pad on the touch input.
Signed-off-by: NAaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add vendor defined touch to support the second generation Intuos Pro.
Previously all generic Wacom devices used true HID to report their touch.
Signed-off-by: NAaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add support for the touchring to the generic code path in support of the second
generation Intuos Pro.

We also add checks for usage->type to ensure that we handle the usage before we
report it, or change the inrange_state based on it.
Signed-off-by: NAaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Input_event_flag duplicates the information we track in
wacom_wac->hid_data.inrange_state for the pad.
Signed-off-by: NAaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

In addition to its USB interface, the second-generation Intuos Pro
includes a Bluetooth radio that offers two pairing interfaces: classic
and low-energy. The classic interface functions just like the earlier
Bluetooth-enabled Intuos4 and Graphire4 tablets, appearing as a HID device
that our driver can work with. The low-energy interface is intented to
be used by userspace applications that make use of its paper-to-digital
capabilities.

Despite the USB interface using Wacom's new vendor-defined HID usages,
the Bluetooth interface provides us with useless black-box "blob"
report descriptors like past devices. We thus have to explicitly add
support for the PIDs and reports used.

These devices pack a /lot/ of information into a single Bluetooth
input report. Each report contains up to seven snapshots of the pen
state, four snapshots of the touch state (of five touches each), pad
state, and battery data. Thankfully this isn't too hard for the driver
to report -- it just takes a fair amount of code to extract!
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

There no reason a Bluetooth device with the appropriate HID descriptor couldn't
be used through the HID_GENERIC codepath in the future. Ensure that the driver
attempts to bind to these devices.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit 345857bb ("HID: wacom: generic: Add support for sensor offsets") included
a change to the operation and location of the call to 'wacom_add_shared_data'
in 'wacom_parse_and_register'. The modifications included moving it higher up
so that it would occur before the call to 'wacom_retrieve_hid_descriptor'. This
was done to prevent a crash that would have occured when the report containing
tablet offsets was fed into the driver with 'wacom_hid_report_raw_event'
(specifically: the various 'wacom_wac_*_report' functions were written with the
assumption that they would only be called once tablet setup had completed;
'wacom_wac_pen_report' in particular dereferences 'shared' which wasn't yet
allocated).

Moving the call to 'wacom_add_shared_data' effectively prevented the crash but
also broke the sibiling detection code which assumes that the HID descriptor
has been read and the various device_type flags set.

To fix this situation, we restore the original 'wacom_add_shared_data'
operation and location and instead implement an alternative change that can
also prevent the crash. Specifically, we notice that the report functions
mentioned above expect to be called only for input reports.  By adding a check,
we can prevent feature reports (such as the offset report) from
causing trouble.

Fixes: 345857bb ("HID: wacom: generic: Add support for sensor offsets")
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Tested-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>