The Armada XP SoCs have multiple PCIe interfaces. The MV78230 has 2
PCIe units (one 4x or quad 1x, the other 1x only), the MV78260 has 3
PCIe units (two 4x or quad 1x and one 4x/1x), the MV78460 has 4 PCIe
units (two 4x or quad 1x and two 4x/1x). We therefore add the
necessary Device Tree informations to make those PCIe interfaces
usable.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada 370 SoC has two 1x PCIe 2.0 interfaces, so we add the
necessary Device Tree informations to make these interfaces availabel.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

In order to be able to use more than 4GB address-cells and size-cells
have to be set to 2
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NLior Amsalem <alior@marvell.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Plat'home Openblocks AX3 has a 128 MiB NOR flash device connected
to the Device Bus. This commit adds the device tree node to support this device.

The SoC supports a flexible and dynamic decoding window allocation scheme;
but since this feature is still not implemented we need to specify the window
base address in the device tree node itself.
This base address has been selected in a completely arbitrary fashion.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada XP Development Board DB-MV784MP-GP has a NOR flash device
connected to the Device Bus. This commit adds the device tree node
to support this device.

This SoC supports a flexible and dynamic decoding window allocation
scheme; but since this feature is still not implemented we need
to specify the window base address in the device tree node itself.

This base address has been selected in a completely arbitrary fashion.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Armada 370 and Armada XP SoC have a Device Bus controller to
handle NOR, NAND, SRAM and FPGA devices.
This patch adds the device tree node to enable the controller.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds support for the thermal controller available in
all Armada 370 boards. This controller has two 4-byte registers:
one to read the thermal sensor, the other for sensor initialization.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds support for the thermal controller available in
all Armada XP boards. This controller has two 4-byte registers:
one to read the thermal sensor, the other for sensor initialization.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add the three external LED definitions to the device tree file on
the Mirabox.

The Mirabox user guide calls out one as a power LED, and the other
two are defined for WiFi, but as the current mwifiex drivers don't
have LED support, we make them status LEDs.

These have been tested working by writing to the appropriate
/sys/class/leds trigger.
Signed-off-by: NRyan Press <ryan@presslab.us>
Tested-by: NNeil Greatorex <neil@fatboyfat.co.uk>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The orion5x SoC includes DMA functionality, so lets enable that
and turn it on by default.
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The orion5x SoC also includes a USB EHCI componment so lets add that
to the dtsi (disable by default incase the pins are not broken out).
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Device tree based guruplug boards still use mvsdio platform_data and
kirkwood_sdio_init to enable sdio. DT support for sdio is already there,
so make use of it.

This also fixes mvsdio accidentially breaking nand by configuring mpp0
to gpio, while used also by nand (nand_io2 on mpp0).
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NSoeren Moch <smoch@web.de>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Marvell Armada 370 Reference Design board has a software-controlled
button on the front side, marked as "SW".
This patch adds minimal support for this button.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add a device tree node to instantiate the dove thermal driver.
Enable the driver and the thermal framework in dove_defconfig.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Kirkwood 88F6282 and 88F6283 have a thermal sensor.
This patch adds a DT node and enables the driver in the kernel config.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Globalscale Mirabox platform can be connected to the JTAG/GPIO box
through the Multi-IO port. The GPIO box use the NXP PCA9505 I/O port
expansion IC to provide 40-bit parallel input/output GPIOs. This patch
enable the use of this expander on the Mirabox.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Before jumping to (position independent) C-code from the decompressor's
assembler world we set-up the C environment. This setup currently does not
set r9, which for arm-none-uclinux-uclibceabi toolchains is by default
expected to be the PIC offset base register (IE should point to the
beginning of the GOT).

Currently, therefore, in order to build working kernels that use the
decompressor it is necessary to use an arm-linux-gnueabi toolchain, or
similar. uClinux toolchains cause a prefetch abort to occur at the beginning
of the decompress_kernel function.

This patch allows uClinux toolchains to build bootable zImages by forcing
the -mno-single-pic-base option, which ensures that the location of the GOT
is re-derived each time it is required, and r9 becomes free for use as a
general purpose register.

This has a small (4% in instruction terms) advantage over the alternative of
setting r9 to point to the GOT before calling into the C-world.
Signed-off-by: NJonathan Austin <jonathan.austin@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Armada 370 Reference Design board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this IP. there are no
GPIOs for card-detect and write-protect so we do not specify any.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Tested-by: NAndrew Lunn <andrew@lunn.ch>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add a DT node for I2C and pinctrl hog for the pins. There appears to
be an i2c bus on topkick with a device on it:

i2cdetect 0
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-0.
I will probe address range 0x03-0x77.
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- 64 -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>

of_serial now has support for using clocks property and we have
a DT clock provider. This patch replaces the hard coded clock-frequency
property with a clocks phandle to tclk.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch add support for the SPI flash MX25l25635E which is present
on the Armada 370 DB board. This flash stores the bootloader and its
environment.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch add support for the SPI flash M25P64 which is present on
the Armada XP DB board. This flash stores the bootloader and its
environment.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds an SPI master device node for Armada XP-GP board.
This master node is an SPI flash controller 'n25q128a13'.

Since there is no 'partitions' node declared, one full sized
partition named as the device will be created.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Tested-by: NGregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NGregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada 370 and Armada XP SoC has an SPI controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.

Note that the Armada XP SPI register length is 0x50 bytes,
while Armada 370 SPI register length is 0x28 bytes,
so we choose the smaller of the two.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: NGregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Now that the time-armada-370-xp support local timers, updated the
device tree to take it into account.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

With DT support for orion-ehci also convert Dove to it and
remove the legacy calls and clock aliases.

This patch is based on "ARM: Dove: split legacy and DT setup"
applied to mvebu/boards recently.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.

Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada 370 and Armada XP SoC has an Orion EHCI USB controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.

Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The OpenBlocks AX3-4 board has one software-controlled button on the
front side, labeled "INIT", so we add minimal support for this button
in the kernel.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Remove C code and add a Device Tree node in its place.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add a sub-node into the I2C node to represent the adt7476 device.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Remove the C code and add a Device Tree node for gpio-poweroff.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

CuBox needs to enable USB power on a gpio pin. Add a fixed regulator
to always enable usb power on boot.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

gpio-leds has support for pinctrl allocation, make use of it.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>