- 13 5月, 2006 15 次提交
-
-
由 Rusty Scott 提交于
Frequency range values in the current driver for the LG TDVS H06xF tuners appear to have been a transposing of the 5 in the mid range 160-455 instead of 165-450. This patch corrects the pll programming for these tuners as per the datasheet. Signed-off-by: NRusty Scott <rustys@ieee.org> Signed-off-by: NMac Michaels <wmichaels1@earthlink.net> Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
This patch prevents a bug where the frontend is unable to tune after waking from powered down state. Now, the device remains powered on until it is disconnected, just like the windows driver. It seems that the bluebird firmware is unable to successfully handle tuning after a powered down state. This patch fixes all of the FusionHDTV Bluebird USB2 devices. The Medion MD95700 will still behave as before, since it was unaffected by this bug. Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Yeasah Pell 提交于
*) Allow forcing the bandselect value with a module parameter to facilitate determining the correct bandselect frequencies. *) Changes the bandselect frequency thresholds based on experiments with the above parameter in conjunction with the values in the spec. Signed-off-by: Yeasah Pell <yeasah at schwide.net> Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Yeasah Pell 提交于
*) Sets an additional tuner parameter (demodulator sample gain) that wasn't being set before. *) Removes the low symbol rate tuner parameter tweaks in the previous patch -- it appears those tweaks are not necessary with the demodulator sample gain set correctly. *) Cleanup and document the demodulator register initialization sequence. *) Change set_fec routine to disable FEC auto scan when a specific code rate is selected. *) Remove error message when reported FEC is invalid (which happens sometimes when the card has no signal) Signed-off-by: Yeasah Pell <yeasah at schwide.net> Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Yeasah Pell 提交于
The previous DISEQC code didn't wait, so it was unreliable Signed-off-by: Yeasah Pell <yeasah at schwide.net> Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Mauro Carvalho Chehab 提交于
Current debug messages at cx24123 are next to useless, since they don't print the values sent/read to registers. With this patch, debug=1 will show comprehensive messages. debug=2 will show also read/write operations at I2C bus. Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
-
由 Vadim Catana 提交于
- fixed the reception of channels with low symbol rates. ( The VGA1 and VGA2 offsets recommended by cx24109 docs for symbol rates from 1 to 5 MSps do not work. I changed them to values found experimentally. The charge pump current and FILTUNE voltage are now set to values recommended in the docs. This improves reception for symbol rates < 15 MSps. The values written in the SYSSymbolRate registers are calculated with better precision. ) - fixed the cx24123_get_fec() function. It was returning the values for DCII mode. - removed some unused variables Signed-off-by: Vadim Catana <skystar at moldova.cc> Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Mauro Carvalho Chehab 提交于
V4L1 API is depreciated and should be removed soon from kernel. This patch adds two new options, one to disable V4L1 drivers, and another to disable V4L1 compat module. This way, it would be easy to check what still depends on V4L1 stuff, allowing also to test if app works fine with V4L2 only support. Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Mauro Carvalho Chehab 提交于
When pluto2 were selected, all other module dependencies were just discarded. Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Andrew de Quincey 提交于
Spotted a couple more places where it fails to check if dvb_register_adapter() fails. Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Andrew de Quincey 提交于
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Andrew de Quincey 提交于
Now that the CI code reinitialises the frontend, need to move the CI initialisation to after the frontend init in order to ensure the frontend is always in a good state. Fixes an oops caused by the frontend being NULL as well. Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Andrew de Quincey 提交于
It turns out the firmware on the TT budget-ci 1.1 slots doesn't generate interrupts. This patch adds support for this using polling mode on these slots. Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Andrew de Quincey 提交于
This mutex is meant to stop two devices getting the same ID. dvbdev_get_free_id() scans the list of already allocated devices to find a free id. Unfortunately, since the mutex is unlocked before the card is added to the above list, it is still possible for two of them to get the same id. Its debatable whether this mutex lock is actually needed, but I'm unwilling to just remove it in case something does depend on it. Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 02 4月, 2006 11 次提交
-
-
由 Andrew de Quincey 提交于
Unfortunately on the budget-av board, the CAM reset line is tied to the frontend reset line, so resetting the CAM also zaps the frontend. This breaks the tda1004x at least, and causes it to fail to tune until the budget-av module is reloaded. This patch adds an exported function to dvb_frontend that allows a card to forcibly reinitialise a frontend. The budget-av now does this on CAM reset, which corrects this problem. since they do not tie the CAM reset line to the frontend reset line. Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Trent Piepho 提交于
The dvr device could be opened multiple times simultaneously in O_RDONLY mode. Each open after the first would allocate a new dvr buffer (1880 KB) and leak the old buffer. The first close would de-allocate the dvr buffer and cause all other open dvrs to stop working. This patch allows only a single O_RDONLY open of the drv device, as per the API specification. Multiple O_WRONLY opens are still allowed and don't appear to cause any problems. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 C.Y.M 提交于
This attached patch was originally proposed by Anssi Hannula to the dvb-kernel user to choose the default broadcast mode when using the ttpci driver. NTSC users need to only add the following line to modprobe.d: options dvb-ttpci tv_standard=1 PAL users will not need to change anything, for this will be the default. Signed-off-by: NC.Y.M <syphir@syphir.sytes.net> Signed-off-by: NOliver Endriss <o.endriss@gmx.de> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Adrian Bunk 提交于
This patch fixes a typo in a comment. Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NOliver Endriss <o.endriss@gmx.de> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Ingo Schneider 提交于
- Issue a warning when more than 80% of the DMA buffer is being used (probably due to bad IRQ latency). Warnings are rate-limited. - Introduce a new parameter 'bufsize' (in KByte) which increases the default DMA buffer of 188 KByte up to 1410 KByte (Activy: 564 KByte). Signed-off-by: NIngo Schneider <mail@ingo-schneider.de> Signed-off-by: NOliver Endriss <o.endriss@gmx.de> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Trent Piepho 提交于
- Added firmware download comments to or51211 and or51132 Kconfig help text. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Patrick Boettcher 提交于
There seems to be a new version of the USB DVB-T stick from WideView with a new demod-revision inside and thus a new firwmare. This patch enables support for that. Thanks to Mikel Martin for early testing. Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
Thanks to: Andrew Cohen <cohen@andy.bu.edu> Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
- Added keycodes for the DViCO FusionHDTV portable remote control. - Enabled the remote control for both versions of FusionHDTV DVB-T USB and the FusionHDTV 5 USB Gold (ATSC) Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 maximilian attems 提交于
The bt8xx drivers uses request_firmware() and thus needs to select FW_LOADER. Signed-off-by: Nmaximilian attems <maks@sternwelten.at> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Mauro Carvalho Chehab 提交于
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 29 3月, 2006 1 次提交
-
-
由 Arjan van de Ven 提交于
Mark the f_ops members of inodes as const, as well as fix the ripple-through this causes by places that copy this f_ops and then "do stuff" with it. Signed-off-by: NArjan van de Ven <arjan@infradead.org> Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 25 3月, 2006 7 次提交
-
-
由 Hans Verkuil 提交于
Add a new audio mode V4L2_TUNER_MODE_LANG1_LANG2 (used by VIDIOC_G/S_TUNER). This mode allows the user to select both languages of a bilingual transmission, one language on the left, one on the right audio channel. If there is no bilingual transmission, or it is not supported, then this mode should act like V4L2_TUNER_MODE_STEREO. This mode is introduced for PVR-like drivers where it is useful to be able to record both languages of a bilingual broadcast. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
Only the Medion boxes return 0x08 after an i2c read/write. The bluebird devices do not return anything at all. This patch conditionalizes the test for the 0x08 return code to produce a warning message when using the Medion box, only. Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
- corrects the wording in some of the debug messages. Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
Removed the FIXME comment from bluebird_patch_dvico_firmware_download: /* FIXME: are we allowed to change the fw-data ? */ Yes, we are allowed. DViCO's Windows driver also does the same thing. A single firmware image is used to support all of the bluebird boxes. The firmware sets all devices to PID: d700. Instead of using that, the driver replaces the d700 with the cold PID+1 before the download. Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
This patch removes the (harmless) -ETIMEDOUT during device init for the DViCO FusionHDTV Bluebird boxes, by conditionalizing the gpio write inside cxusb_i2c_xfer to happen only for Medion boxes. Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Patrick Boettcher 提交于
There was no MODULE_DEVICE_TABLE for the b2c2-flexcop-usb module. This makes it impossible for hotplug to load the module automatically, when such a device is connected. Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Manu Abraham 提交于
Signed-off-by: NManu Abraham <manu@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 22 3月, 2006 6 次提交
-
-
由 Linus Torvalds 提交于
This reverts commit 08f1d0b9 The "bt8xx/ conversion" for drivers/video/ hasn't actually percolated all the way to this tree, so the Makefile change escaped too soon. Build breakage noticed by Jeff Garzik <jeff@garzik.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Manu Abraham 提交于
Signed-off-by: NManu Abraham <manu@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Oliver Endriss 提交于
Add wss_cfg_4_3 and wss_cfg_16_9 configuration options. Firmware 2623 or later required. Both parameters are bit masks: - bit 15: disable WSS - bit 14: send short WSS burst, then turn off WSS - bit 13..0: WSS bits as specified by the standard These parameters are useful if you own a broken tv set which does not handle wss correctly. Default settings: - wss_cfg_4_3: 0x4008 - wss_cfg_16_9: 0x0007 These should work with most devices. Signed-off-by: NOliver Endriss <o.endriss@gmx.de> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Perceval Anichini 提交于
Moved duplicated code of ALPS BSRU6 tuner to a standalone file. Modified av7110 and budget drivers to include the new file. Signed-off-by: NPerceval Anichini <perceval.anichini@streamvision.fr> Signed-off-by: NOliver Endriss <o.endriss@gmx.de> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Michael Krufky 提交于
- Corrected typo for NxtWave NXT200X - Added "Oren" manufacturer name to menu items for OR51132 and OR51211 - Removed "(pcHDTV HDx000 card)" from Oren frontends menu item names, This isn't necessary, as these frontends are selected by the card drivers, build configuration (DVB_BT8XX and VIDEO_CX88_DVB). Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Adrian Bunk 提交于
Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-