- 31 8月, 2013 1 次提交
-
-
由 Alan Stern 提交于
This patch fixes a build error that occurs when CONFIG_PM is enabled and CONFIG_PM_SLEEP isn't: >> drivers/usb/host/ohci-pci.c:294:10: error: 'usb_hcd_pci_pm_ops' undeclared here (not in a function) .pm = &usb_hcd_pci_pm_ops Since the usb_hcd_pci_pm_ops structure is defined and used when CONFIG_PM is enabled, its declaration should not be protected by CONFIG_PM_SLEEP. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Reported-by: Nkbuild test robot <fengguang.wu@intel.com> CC: <stable@vger.kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 29 8月, 2013 1 次提交
-
-
由 Dmitry Kasatkin 提交于
When DEBUG is defined, dev_dbg_ratelimited uses dynamic debug data structures even when CONFIG_DYNAMIC_DEBUG is not defined. It leads to build break. For example, when I try to use dev_dbg_ratelimited in USB code and CONFIG_USB_DEBUG is enabled, but CONFIG_DYNAMIC_DEBUG is not, I get: CC [M] drivers/usb/host/xhci-ring.o drivers/usb/host/xhci-ring.c: In function ‘xhci_queue_intr_tx’: drivers/usb/host/xhci-ring.c:3059:3: error: implicit declaration of function ‘DEFINE_DYNAMIC_DEBUG_METADATA’ [-Werror=implicit-function-declaration] drivers/usb/host/xhci-ring.c:3059:3: error: ‘descriptor’ undeclared (first use in this function) drivers/usb/host/xhci-ring.c:3059:3: note: each undeclared identifier is reported only once for each function it appears in drivers/usb/host/xhci-ring.c:3059:3: error: implicit declaration of function ‘__dynamic_pr_debug’ [-Werror=implicit-function-declaration] drivers/usb/host/xhci-ring.c: In function ‘xhci_queue_isoc_tx_prepare’: drivers/usb/host/xhci-ring.c:3847:3: error: ‘descriptor’ undeclared (first use in this function) cc1: some warnings being treated as errors make[2]: *** [drivers/usb/host/xhci-ring.o] Error 1 make[1]: *** [drivers/usb/host] Error 2 make: *** [drivers/usb/] Error 2 This patch separates definition for CONFIG_DYNAMIC_DEBUG and DEBUG cases. [Note, Sarah moved the comment above the macro to avoid checkpatch warnings.] Signed-off-by: NDmitry Kasatkin <d.kasatkin@samsung.com> Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 16 8月, 2013 3 次提交
-
-
由 Linus Torvalds 提交于
Ben Tebulin reported: "Since v3.7.2 on two independent machines a very specific Git repository fails in 9/10 cases on git-fsck due to an SHA1/memory failures. This only occurs on a very specific repository and can be reproduced stably on two independent laptops. Git mailing list ran out of ideas and for me this looks like some very exotic kernel issue" and bisected the failure to the backport of commit 53a59fc6 ("mm: limit mmu_gather batching to fix soft lockups on !CONFIG_PREEMPT"). That commit itself is not actually buggy, but what it does is to make it much more likely to hit the partial TLB invalidation case, since it introduces a new case in tlb_next_batch() that previously only ever happened when running out of memory. The real bug is that the TLB gather virtual memory range setup is subtly buggered. It was introduced in commit 597e1c35 ("mm/mmu_gather: enable tlb flush range in generic mmu_gather"), and the range handling was already fixed at least once in commit e6c495a9 ("mm: fix the TLB range flushed when __tlb_remove_page() runs out of slots"), but that fix was not complete. The problem with the TLB gather virtual address range is that it isn't set up by the initial tlb_gather_mmu() initialization (which didn't get the TLB range information), but it is set up ad-hoc later by the functions that actually flush the TLB. And so any such case that forgot to update the TLB range entries would potentially miss TLB invalidates. Rather than try to figure out exactly which particular ad-hoc range setup was missing (I personally suspect it's the hugetlb case in zap_huge_pmd(), which didn't have the same logic as zap_pte_range() did), this patch just gets rid of the problem at the source: make the TLB range information available to tlb_gather_mmu(), and initialize it when initializing all the other tlb gather fields. This makes the patch larger, but conceptually much simpler. And the end result is much more understandable; even if you want to play games with partial ranges when invalidating the TLB contents in chunks, now the range information is always there, and anybody who doesn't want to bother with it won't introduce subtle bugs. Ben verified that this fixes his problem. Reported-bisected-and-tested-by: NBen Tebulin <tebulin@googlemail.com> Build-testing-by: NStephen Rothwell <sfr@canb.auug.org.au> Build-testing-by: NRichard Weinberger <richard.weinberger@gmail.com> Reviewed-by: NMichal Hocko <mhocko@suse.cz> Acked-by: NPeter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Thomas Pugliese 提交于
When the HWA encounters a STALL on a control endpoint, it should clear the RPIPE_STALL feature on the RPIPE before processing the next transfer request. Otherwise, all transfer requests on that endpoint after the first STALL will fail because the RPIPE is still in the halted state. This also removes the unneccessary call to spin_lock_irqsave for a nested lock that was present in the first patch. Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Moshe Lazer 提交于
In the previous QUERY_PAGES command version we used one command to get the required amount of boot, init and post init pages. The new version uses the op_mod field to specify whether the query is for the required amount of boot, init or post init pages. In addition the output field size for the required amount of pages increased from 16 to 32 bits. In MANAGE_PAGES command the input_num_entries and output_num_entries fields sizes changed from 16 to 32 bits and the PAS tables offset changed to 0x10. In the pages request event the num_pages field also changed to 32 bits. In the HCA-capabilities-layout the size and location of max_qp_mcg field has been changed to support 24 bits. This patch isn't compatible with firmware versions < 5; however, it turns out that the first GA firmware we will publish will not support previous versions so this should be OK. Signed-off-by: NMoshe Lazer <moshel@mellanox.com> Signed-off-by: NEli Cohen <eli@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 8月, 2013 4 次提交
-
-
由 Jesper Dangaard Brouer 提交于
commit 56b765b7 ("htb: improved accuracy at high rates") broke the "linklayer atm" handling. tc class add ... htb rate X ceil Y linklayer atm The linklayer setting is implemented by modifying the rate table which is send to the kernel. No direct parameter were transferred to the kernel indicating the linklayer setting. The commit 56b765b7 ("htb: improved accuracy at high rates") removed the use of the rate table system. To keep compatible with older iproute2 utils, this patch detects the linklayer by parsing the rate table. It also supports future versions of iproute2 to send this linklayer parameter to the kernel directly. This is done by using the __reserved field in struct tc_ratespec, to convey the choosen linklayer option, but only using the lower 4 bits of this field. Linklayer detection is limited to speeds below 100Mbit/s, because at high rates the rtab is gets too inaccurate, so bad that several fields contain the same values, this resembling the ATM detect. Fields even start to contain "0" time to send, e.g. at 1000Mbit/s sending a 96 bytes packet cost "0", thus the rtab have been more broken than we first realized. Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter Chen 提交于
Currently, the controller only runs when the ci->vbus_active is true. So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer. If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change to update ci->vbus_active. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Peter Chen 提交于
Since we need otgsc to know vbus's status at some chipidea controllers even it is peripheral-only mode. Besides, some SoCs (eg, AR9331 SoC) don't have otgsc register even the DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS. We inroduce flag CI_HDRC_DUAL_ROLE_NOT_OTG to indicate if the controller is dual role, but not supports OTG. If this flag is not set, we follow the rule that if DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS, then this controller is otg capable. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Peter Chen 提交于
The vbus regulator is a common element for USB vbus operation, So, move it from glue layer to core. Tested-by: NMarek Vasut <marex@denx.de> Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 14 8月, 2013 5 次提交
-
-
由 Radu Caragea 提交于
When the stack is set to unlimited, the bottomup direction is used for mmap-ings but the mmap_base is not used and thus effectively renders ASLR for mmapings along with PIE useless. Cc: Michel Lespinasse <walken@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Reviewed-by: NRik van Riel <riel@redhat.com> Acked-by: NIngo Molnar <mingo@kernel.org> Cc: Adrian Sendroiu <molecula2788@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Michal Simek 提交于
Fix inadvertent breakage in the clone syscall ABI for Microblaze that was introduced in commit f3268edb ("microblaze: switch to generic fork/vfork/clone"). The Microblaze syscall ABI for clone takes the parent tid address in the 4th argument; the third argument slot is used for the stack size. The incorrectly-used CLONE_BACKWARDS type assigned parent tid to the 3rd slot. This commit restores the original ABI so that existing userspace libc code will work correctly. All kernel versions from v3.8-rc1 were affected. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Cyrill Gorcunov 提交于
Andy reported that if file page get reclaimed we lose the soft-dirty bit if it was there, so save _PAGE_BIT_SOFT_DIRTY bit when page address get encoded into pte entry. Thus when #pf happens on such non-present pte we can restore it back. Reported-by: NAndy Lutomirski <luto@amacapital.net> Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org> Acked-by: NPavel Emelyanov <xemul@parallels.com> Cc: Matt Mackall <mpm@selenic.com> Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Cyrill Gorcunov 提交于
Andy Lutomirski reported that if a page with _PAGE_SOFT_DIRTY bit set get swapped out, the bit is getting lost and no longer available when pte read back. To resolve this we introduce _PTE_SWP_SOFT_DIRTY bit which is saved in pte entry for the page being swapped out. When such page is to be read back from a swap cache we check for bit presence and if it's there we clear it and restore the former _PAGE_SOFT_DIRTY bit back. One of the problem was to find a place in pte entry where we can save the _PTE_SWP_SOFT_DIRTY bit while page is in swap. The _PAGE_PSE was chosen for that, it doesn't intersect with swap entry format stored in pte. Reported-by: NAndy Lutomirski <luto@amacapital.net> Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org> Acked-by: NPavel Emelyanov <xemul@parallels.com> Cc: Matt Mackall <mpm@selenic.com> Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Reviewed-by: NMinchan Kim <minchan@kernel.org> Reviewed-by: NWanpeng Li <liwanp@linux.vnet.ibm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Pravin B Shelar 提交于
Using inner-id for tunnel id is not safe in some rare cases. E.g. packets coming from multiple sources entering same tunnel can have same id. Therefore on tunnel packet receive we could have packets from two different stream but with same source and dst IP with same ip-id which could confuse ip packet reassembly. Following patch reverts optimization from commit 490ab081 (IP_GRE: Fix IP-Identification.) CC: Jarno Rajahalme <jrajahalme@nicira.com> CC: Ansis Atteka <aatteka@nicira.com> Signed-off-by: NPravin B Shelar <pshelar@nicira.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 8月, 2013 6 次提交
-
-
由 Oleg Nesterov 提交于
This is only theoretical, but after try_to_wake_up(p) was changed to check p->state under p->pi_lock the code like __set_current_state(TASK_INTERRUPTIBLE); schedule(); can miss a signal. This is the special case of wait-for-condition, it relies on try_to_wake_up/schedule interaction and thus it does not need mb() between __set_current_state() and if(signal_pending). However, this __set_current_state() can move into the critical section protected by rq->lock, now that try_to_wake_up() takes another lock we need to ensure that it can't be reordered with "if (signal_pending(current))" check inside that section. The patch is actually one-liner, it simply adds smp_wmb() before spin_lock_irq(rq->lock). This is what try_to_wake_up() already does by the same reason. We turn this wmb() into the new helper, smp_mb__before_spinlock(), for better documentation and to allow the architectures to change the default implementation. While at it, kill smp_mb__after_lock(), it has no callers. Perhaps we can also add smp_mb__before/after_spinunlock() for prepare_to_wait(). Signed-off-by: NOleg Nesterov <oleg@redhat.com> Acked-by: NPeter Zijlstra <peterz@infradead.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Ming Lei 提交于
This patch introduces support of DMA SG if the USB host controller which usbnet device is attached to is capable of building packet from discontinuous buffers. The patch supports passing the skb fragment buffers to usb stack directly via urb->sg. Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Grant Grundler <grundler@google.com> Cc: Freddy Xin <freddy@asix.com.tw> Cc: Alan Stern <stern@rowland.harvard.edu> Acked-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NMing Lei <ming.lei@canonical.com> Reviewed-by: NEric Dumazet <edumazet@google.com> Acked-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Ming Lei 提交于
Some host controllers(such as xHCI) can support building packet from discontinuous buffers, so introduce one flag and helper for this kind of host controllers, then the feature can help some applications(such as usbnet) by supporting arbitrary length of sg buffers. Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NMing Lei <ming.lei@canonical.com> Reviewed-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Ming Lei 提交于
This patch implements the mechanism of giveback of URB in tasklet context, so that hardware interrupt handling time for usb host controller can be saved much, and HCD interrupt handling can be simplified. Motivations: 1), on some arch(such as ARM), DMA mapping/unmapping is a bit time-consuming, for example: when accessing usb mass storage via EHCI on pandaboard, the common length of transfer buffer is 120KB, the time consumed on DMA unmapping may reach hundreds of microseconds; even on A15 based box, the time is still about scores of microseconds 2), on some arch, reading DMA coherent memoery is very time-consuming, the most common example is usb video class driver[1] 3), driver's complete() callback may do much things which is driver specific, so the time is consumed unnecessarily in hardware irq context. 4), running driver's complete() callback in hardware irq context causes that host controller driver has to release its lock in interrupt handler, so reacquiring the lock after return may busy wait a while and increase interrupt handling time. More seriously, releasing the HCD lock makes HCD becoming quite complicated to deal with introduced races. So the patch proposes to run giveback of URB in tasklet context, then time consumed in HCD irq handling doesn't depend on drivers' complete and DMA mapping/unmapping any more, also we can simplify HCD since the HCD lock isn't needed to be released during irq handling. The patch should be reasonable and doable: 1), for drivers, they don't care if the complete() is called in hard irq context or softirq context 2), the biggest change is the situation in which usb_submit_urb() is called in complete() callback, so the introduced tasklet schedule delay might be a con, but it shouldn't be a big deal: - control/bulk asynchronous transfer isn't sensitive to schedule delay - the patch schedules giveback of periodic URBs using tasklet_hi_schedule, so the introduced delay should be very small - for ISOC transfer, generally, drivers submit several URBs concurrently to avoid interrupt delay, so it is OK with the little schedule delay. - for interrupt transfer, generally, drivers only submit one URB at the same time, but interrupt transfer is often used in event report, polling, ... situations, and a little delay should be OK. Considered that HCDs may optimize on submitting URB in complete(), the patch may cause the optimization not working, so introduces one flag to mark if the HCD supports to run giveback URB in tasklet context. When all HCDs are ready, the flag can be removed. [1], http://marc.info/?t=136438111600010&r=1&w=2 Cc: Oliver Neukum <oliver@neukum.org> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NMing Lei <ming.lei@canonical.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Tuomas Tynkkynen 提交于
The Tegra30 TRM recommends configuration of certain PHY parameters for optimal quality. Program the following registers based on device tree parameters: - UTMIP_XCVR_HSSLEW: HS slew rate control. - UTMIP_HSSQUELCH_LEVEL: HS squelch detector level - UTMIP_HSDISCON_LEVEL: HS disconnect detector level. These registers exist in Tegra20, but programming them hasn't been necessary, so these parameters won't be set on Tegra20 to keep the device trees backward compatible. Additionally, the UTMIP_XCVR_SETUP parameter can be set from fuses instead of a software-programmed value, as the optimal value can vary between invidual boards. The boolean property nvidia,xcvr-setup-use-fuses can be used to enable this behaviour. Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com> Tested-by: NStephen Warren <swarren@nvidia.com> Reviewed-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Tuomas Tynkkynen 提交于
The Tegra30 USB PHY is a bit different than the Tegra20 PHY: - The EHCI controller supports the HOSTPC register extension, and some of the fields that the PHY needs to modify (PHCD and PTS) have moved to the new HOSTPC register. - Some of the UTMI PLL configuration registers have moved from the USB register space to the Clock-And-Reset controller space. In Tegra30 the clock driver is responsible for configuring the UTMI PLL. - The USBMODE register must be explicitly written to enter host mode. - Certain PHY parameters need to be programmed for optimal signal quality. Support for this will be added in the next patch. The new tegra_phy_soc_config structure is added to describe the differences between the SoCs. Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com> Tested-by: NStephen Warren <swarren@nvidia.com> Reviewed-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
- 10 8月, 2013 1 次提交
-
-
由 Eliezer Tamir 提交于
Rename mib counter from "low latency" to "busy poll" v1 also moved the counter to the ip MIB (suggested by Shawn Bohrer) Eric Dumazet suggested that the current location is better. So v2 just renames the counter to fit the new naming convention. Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 8月, 2013 2 次提交
-
-
The "nop" driver isn't a do-nothing-stub but supports a couple functions like clock on/off or is able to use a voltage regulator. This patch simply renames the driver to "generic" since it is easy possible to extend it by a simple function istead of writing a complete driver. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Oleg Nesterov 提交于
Ensure that user_namespace->parent chain can't grow too much. Currently we use the hardroded 32 as limit. Reported-by: NAndy Lutomirski <luto@amacapital.net> Signed-off-by: NOleg Nesterov <oleg@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 08 8月, 2013 2 次提交
-
-
由 Trond Myklebust 提交于
If rpcbind causes our connection to the AF_LOCAL socket to close after we've registered a service, then we want to be careful about reconnecting since the mount namespace may have changed. By simply refusing to reconnect the AF_LOCAL socket in the case of unregister, we avoid the need to somehow save the mount namespace. While this may lead to some services not unregistering properly, it should be safe. Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com> Cc: Nix <nix@esperi.org.uk> Cc: Jeff Layton <jlayton@redhat.com> Cc: stable@vger.kernel.org # 3.9.x
-
由 Rafael J. Wysocki 提交于
In theory, under a given ACPI namespace node there should be only one child device object with _ADR whose value matches a given bus address exactly. In practice, however, there are systems in which multiple child device objects under a given parent have _ADR matching exactly the same address. In those cases we use _STA to determine which of the multiple matching devices is enabled, since some systems are known to indicate which ACPI device object to associate with the given physical (usually PCI) device this way. Unfortunately, as it turns out, there are systems in which many device objects under the same parent have _ADR matching exactly the same bus address and none of them has _STA, in which case they all should be regarded as enabled according to the spec. Still, if those device objects are supposed to represent bridges (e.g. this is the case for device objects corresponding to PCIe ports), we can try harder and skip the ones that have no child device objects in the ACPI namespace. With luck, we can avoid using device objects that we are not expected to use this way. Although this only works for bridges whose children also have ACPI namespace representation, it is sufficient to address graphics adapter detection issues on some systems, so rework the code finding a matching device ACPI handle for a given bus address to implement this idea. Introduce a new function, acpi_find_child(), taking three arguments: the ACPI handle of the device's parent, a bus address suitable for the device's bus type and a bool indicating if the device is a bridge and make it work as outlined above. Reimplement the function currently used for this purpose, acpi_get_child(), as a call to acpi_find_child() with the last argument set to 'false' and make the PCI subsystem use acpi_find_child() with the bridge information passed as the last argument to it. [Lan Tianyu notices that it is not sufficient to use pci_is_bridge() for that, because the device's subordinate pointer hasn't been set yet at this point, so use hdr_type instead.] This change fixes a regression introduced inadvertently by commit 33f767d7 (ACPI: Rework acpi_get_child() to be more efficient) which overlooked the fact that for acpi_walk_namespace() "post-order" means "after all children have been visited" rather than "on the way back", so for device objects without children and for namespace walks of depth 1, as in the acpi_get_child() case, the "post-order" callbacks ordering is actually the same as the ordering of "pre-order" ones. Since that commit changed the namespace walk in acpi_get_child() to terminate after finding the first matching object instead of going through all of them and returning the last one, it effectively changed the result returned by that function in some rare cases and that led to problems (the switch from a "pre-order" to a "post-order" callback was supposed to prevent that from happening, but it was ineffective). As it turns out, the systems where the change made by commit 33f767d7 actually matters are those where there are multiple ACPI device objects representing the same PCIe port (which effectively is a bridge). Moreover, only one of them, and the one we are expected to use, has child device objects in the ACPI namespace, so the regression can be addressed as described above. References: https://bugzilla.kernel.org/show_bug.cgi?id=60561Reported-by: NPeter Wu <lekensteyn@gmail.com> Tested-by: NVladimir Lalov <mail@vlalov.com> Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: NBjorn Helgaas <bhelgaas@google.com> Cc: 3.9+ <stable@vger.kernel.org> # 3.9+
-
- 07 8月, 2013 1 次提交
-
-
由 Mateusz Krawczuk 提交于
regmap.h requires linux/err.h if CONFIG_REGMAP is not defined. Without it I get error. CC drivers/media/platform/exynos4-is/fimc-reg.o In file included from drivers/media/platform/exynos4-is/fimc-reg.c:14:0: include/linux/regmap.h: In function ‘regmap_write’: include/linux/regmap.h:525:10: error: ‘EINVAL’ undeclared (first use in this function) include/linux/regmap.h:525:10: note: each undeclared identifier is reported only once for each function it appears in Signed-off-by: NMateusz Krawczuk <m.krawczuk@partner.samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NMark Brown <broonie@linaro.org> Cc: stable@kernel.org
-
- 06 8月, 2013 2 次提交
-
-
由 Rafael J. Wysocki 提交于
The physical_node_id_bitmap in struct acpi_device is only used for looking up the first currently unused dependent phyiscal node ID by acpi_bind_one(). It is not really necessary, however, because acpi_bind_one() walks the entire physical_node_list of the given device object for sanity checking anyway and if that list is always sorted by node_id, it is straightforward to find the first gap between the currently used node IDs and use that number as the ID of the new list node. This also removes the artificial limit of the maximum number of dependent physical devices per ACPI device object, which now depends only on the capacity of unsigend int. As a result, it fixes a regression introduced by commit e2ff3940 (ACPI / memhotplug: Bind removable memory blocks to ACPI device nodes) that caused acpi_memory_enable_device() to fail when the number of 128 MB blocks within one removable memory module was greater than 32. Reported-and-tested-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: NToshi Kani <toshi.kani@hp.com> Reviewed-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
-
由 Eli Cohen 提交于
Remove this code, per Dave Miller's request, since it is not being used anywhere in the kernel. Signed-off-by: NEli Cohen <eli@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 8月, 2013 1 次提交
-
-
由 Eliezer Tamir 提交于
When renaming ll_poll to busy poll, I introduced a typo in the name of the do-nothing placeholder for sk_busy_loop and called it sk_busy_poll. This broke compile when busy poll was not configured. Cong Wang submitted a patch to fixed that. This patch removes the now redundant, misspelled placeholder. Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 8月, 2013 3 次提交
-
-
由 Yacine Belkadi 提交于
When building the htmldocs (in verbose mode), scripts/kernel-doc reports the following type of warnings: Warning(drivers/usb/core/usb.c:76): No description found for return value of 'usb_find_alt_setting' Fix them by: - adding some missing descriptions of return values - using "Return" sections for those descriptions Signed-off-by: NYacine Belkadi <yacine.belkadi.1@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Dhaval Giani 提交于
When CONFIG_TRACING is not enabled, the stub prototype for trace_dump_stack() is incorrect. It has (void) when it should be (int). Link: http://lkml.kernel.org/r/CAPhKKr_H=ukFnBL4WgDOVT5ay2xeF-Ho+CA0DWZX0E2JW-=vSQ@mail.gmail.comSigned-off-by: NDhaval Giani <dhaval.giani@gmail.com> Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
-
由 Andrew Vagin 提交于
tracing_read_pipe zeros all fields bellow "seq". The declaration contains a comment about that, but it doesn't help. The first field is "snapshot", it's true when current open file is snapshot. Looks obvious, that it should not be zeroed. The second field is "started". It was converted from cpumask_t to cpumask_var_t (v2.6.28-4983-g4462344e), in other words it was converted from cpumask to pointer on cpumask. Currently the reference on "started" memory is lost after the first read from tracing_read_pipe and a proper object will never be freed. The "started" is never dereferenced for trace_pipe, because trace_pipe can't have the TRACE_FILE_ANNOTATE options. Link: http://lkml.kernel.org/r/1375463803-3085183-1-git-send-email-avagin@openvz.org Cc: stable@vger.kernel.org # 2.6.30 Signed-off-by: NAndrew Vagin <avagin@openvz.org> Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
-
- 02 8月, 2013 3 次提交
-
-
由 Cong Wang 提交于
Eliezer renames several *ll_poll to *busy_poll, but forgets CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too. Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: NCong Wang <amwang@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Cong Wang 提交于
When CONFIG_NET_LL_RX_POLL is not set, I got: net/socket.c: In function ‘sock_poll’: net/socket.c:1165:4: error: implicit declaration of function ‘sk_busy_loop’ [-Werror=implicit-function-declaration] Fix this by adding a nop when !CONFIG_NET_LL_RX_POLL. Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: NCong Wang <amwang@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubeček 提交于
On a high-traffic router with many processors and many IPv6 dst entries, soft lockup in fib6_run_gc() can occur when number of entries reaches gc_thresh. This happens because fib6_run_gc() uses fib6_gc_lock to allow only one thread to run the garbage collector but ip6_dst_gc() doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc() returns. On a system with many entries, this can take some time so that in the meantime, other threads pass the tests in ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for the lock. They then have to run the garbage collector one after another which blocks them for quite long. Resolve this by replacing special value ~0UL of expire parameter to fib6_run_gc() by explicit "force" parameter to choose between spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with force=false if gc_thresh is reached but not max_size. Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 8月, 2013 5 次提交
-
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Hocko 提交于
vmpressure is called synchronously from reclaim where the target_memcg is guaranteed to be alive but the eventfd is signaled from the work queue context. This means that memcg (along with vmpressure structure which is embedded into it) might go away while the work item is pending which would result in use-after-release bug. We have two possible ways how to fix this. Either vmpressure pins memcg before it schedules vmpr->work and unpin it in vmpressure_work_fn or explicitely flush the work item from the css_offline context (as suggested by Tejun). This patch implements the later one and it introduces vmpressure_cleanup which flushes the vmpressure work queue item item. It hooks into mem_cgroup_css_offline after the memcg itself is cleaned up. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: NMichal Hocko <mhocko@suse.cz> Reported-by: NTejun Heo <tj@kernel.org> Cc: Anton Vorontsov <anton.vorontsov@linaro.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Li Zefan <lizefan@huawei.com> Acked-by: NTejun Heo <tj@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Michal Hocko 提交于
There is nothing that can sleep inside critical sections protected by this lock and those sections are really small so there doesn't make much sense to use mutex for them. Change the log to a spinlock Signed-off-by: NMichal Hocko <mhocko@suse.cz> Reported-by: NTejun Heo <tj@kernel.org> Cc: Anton Vorontsov <anton.vorontsov@linaro.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Li Zefan <lizefan@huawei.com> Reviewed-by: NTejun Heo <tj@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Eli Cohen 提交于
Introduce enbale_hca and disable_hca commands to signify when the driver starts or ceases to operate on the device. In addition the driver will use boot and init pages count; boot pages is required to allow firmware to complete boot commands and the other to complete init hca. Command interface revision is bumped to 4 to enforce using supported firmware. This patch breaks compatibility with old versions of firmware (< 4); however, the first GA firmware we will publish will support version 4 so this should not be a problem. Signed-off-by: NEli Cohen <eli@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Oleg Nesterov 提交于
Change trace_remove_event_call(call) to return the error if this call is active. This is what the callers assume but can't verify outside of the tracing locks. Both trace_kprobe.c/trace_uprobe.c need the additional changes, unregister_trace_probe() should abort if trace_remove_event_call() fails. The caller is going to free this call/file so we must ensure that nobody can use them after trace_remove_event_call() succeeds. debugfs should be fine after the previous changes and event_remove() does TRACE_REG_UNREGISTER, but still there are 2 reasons why we need the additional checks: - There could be a perf_event(s) attached to this tp_event, so the patch checks ->perf_refcount. - TRACE_REG_UNREGISTER can be suppressed by FTRACE_EVENT_FL_SOFT_MODE, so we simply check FTRACE_EVENT_FL_ENABLED protected by event_mutex. Link: http://lkml.kernel.org/r/20130729175033.GB26284@redhat.comReviewed-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: NOleg Nesterov <oleg@redhat.com> Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
-