Currently we don't check that the link type is Eth and hence crash
on IB ports when attempting to deref esw->xxx, fix that.

To avoid repeating this check over and over, put the existing
checks and the one on link type in a single helper.

Fixes: 7768d197 ('net/mlx5: E-Switch, Add control for encapsulation')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NMohamad Badarnah <mohamadb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The offending commit only changed the code path for PF/VF, but it
didn't take care of VF representors. As a result, since
params->tx_min_inline_mode for VF representors is kzalloced to 0
(MLX5_INLINE_MODE_NONE), all VF reps SQs were set to that mode.

This actually works on CX5 by default but broke CX4. Fix that by
adding a call to query the min inline mode from the VF rep build up code.

Fixes: a6f402e4 ("net/mlx5e: Tx, no inline copy on ConnectX-5")
Signed-off-by: NChris Mi <chrism@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Misuse of (BIT) macro caused to report wrong flags for
"Hardware Transmit Timestamp Modes" and "Hardware Receive
Filter Modes"

Fixes: ef9814de ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: NMaor Dickman <maord@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.

If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address.  This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.

Fixes: e3297246 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The referenced file dsa.txt is located at
Documentation/devicetree/bindings/net/dsa/dsa.txt
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In sctp_for_each_transport, pos is used to save how many objs it has
dumped. Now it gets the last obj by sctp_transport_get_idx, then gets
the next obj by sctp_transport_get_next.

The issue is that in the meanwhile if some objs in transport hashtable
are removed and the objs nums are less than pos, sctp_transport_get_idx
would return NULL and hti.walker.tbl is NULL as well. At this moment
it should stop hti, instead of continue getting the next obj. Or it
would cause a NULL pointer dereference in sctp_transport_get_next.

This patch is to pass pos + 1 into sctp_transport_get_idx to get the
next obj directly, even if pos > objs nums, it would return NULL and
stop hti.

Fixes: 626d16f5 ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes CVE-2017-7482.

When a kerberos 5 ticket is being decoded so that it can be loaded into an
rxrpc-type key, there are several places in which the length of a
variable-length field is checked to make sure that it's not going to
overrun the available data - but the data is padded to the nearest
four-byte boundary and the code doesn't check for this extra.  This could
lead to the size-remaining variable wrapping and the data pointer going
over the end of the buffer.

Fix this by making the various variable-length data checks use the padded
length.
Reported-by: N石磊 <shilei-c@360.cn>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Reviewed-by: NMarc Dionne <marc.c.dionne@auristor.com>
Reviewed-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now when starting the dad work in addrconf_mod_dad_work, if the dad work
is idle and queued, it needs to hold ifa.

The problem is there's one gap in [1], during which if the pending dad work
is removed elsewhere. It will miss to hold ifa, but the dad word is still
idea and queue.

        if (!delayed_work_pending(&ifp->dad_work))
                in6_ifa_hold(ifp);
                    <--------------[1]
        mod_delayed_work(addrconf_wq, &ifp->dad_work, delay);

An use-after-free issue can be caused by this.

Chen Wei found this issue when WARN_ON(!hlist_unhashed(&ifp->addr_lst)) in
net6_ifa_finish_destroy was hit because of it.

As Hannes' suggestion, this patch is to fix it by holding ifa first in
addrconf_mod_dad_work, then calling mod_delayed_work and putting ifa if
the dad_work is already in queue.

Note that this patch did not choose to fix it with:

  if (!mod_delayed_work(delay))
          in6_ifa_hold(ifp);

As with it, when delay == 0, dad_work would be scheduled immediately, all
addrconf_mod_dad_work(0) callings had to be moved under ifp->lock.
Reported-by: NWei Chen <weichen@redhat.com>
Suggested-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) The netlink attribute passed in to dev_set_alias() is not
    necessarily NULL terminated, don't use strlcpy() on it. From
    Alexander Potapenko.

 2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
    Borkmann.

 3) Correct the release of netdevs and driver private data in certain
    circumstances.

 4) Sanitize netlink message length properly in decnet, from Mateusz
    Jurczyk.

 5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
    Yuval Mintz.

 6) Hash secret is never initialized in ipv6 ILA translation code, from
    Arnd Bergmann. I guess those clang warnings about unused inline
    functions are useful for something!

 7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.

 8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
    and CAIF. From Mateusz Jurczyk.

 9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
    Molitor.

10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
    Johannes Berg.

11) Fix locking in sctp_for_each_endpoint(), from Xin Long.

12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.

13) Fix use after free in ip_mc_clear_src(), from WANG Cong.

14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
    Jesper Dangaard Brouer.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
  i40e: Fix a sleep-in-atomic bug
  net: don't global ICMP rate limit packets originating from loopback
  net/act_pedit: fix an error code
  net: update undefined ->ndo_change_mtu() comment
  net_sched: move tcf_lock down after gen_replace_estimator()
  caif: Add sockaddr length check before accessing sa_family in connect handler
  qed: fix dump of context data
  qmi_wwan: new Telewell and Sierra device IDs
  net: phy: Fix MDIO_THUNDER dependencies
  netconsole: Remove duplicate "netconsole: " logging prefix
  igmp: acquire pmc lock for ip_mc_clear_src()
  r8152: give the device version
  net: rps: fix uninitialized symbol warning
  mac80211: don't send SMPS action frame in AP mode when not needed
  mac80211/wpa: use constant time memory comparison for MACs
  mac80211: set bss_info data before configuring the channel
  mac80211: remove 5/10 MHz rate code from station MLME
  mac80211: Fix incorrect condition when checking rx timestamp
  mac80211: don't look at the PM bit of BAR frames
  i40e: fix handling of HW ATR eviction
  ...

Pull crypto fix from Herbert Xu:
 "This fixes a bug on sparc where we may dereference freed stack memory"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: Work around deallocated stack frame reference gcc bug on sparc.

Pull ACPI fixes from Rafael Wysocki:
 "These revert an ACPICA commit from the 4.11 cycle that causes problems
  to happen on some systems and add a protection against possible kernel
  crashes due to table reference counter imbalance.

  Specifics:

   - Revert a 4.11 ACPICA change that made assumptions which are not
     satisfied on some systems and caused the enumeration of resources
     to fail on them (Rafael Wysocki).

   - Add a mechanism to prevent tables from being unmapped prematurely
     due to reference counter overflows (Lv Zheng)"

* tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
  Revert "ACPICA: Disassembler: Enhance resource descriptor detection"

Pull power management fixes from Rafael Wysocki:
 "These revert a recent cpufreq schedutil governor change that turned
  out to be problematic and fix a few minor issues in cpufreq, cpuidle
  and the Exynos devfreq drivers.

  Specifics:

   - Revert a recent cpufreq schedutil governor change that caused some
     systems to behave undesirably (Rafael Wysocki).

   - Fix a cpufreq conservative governor issue introduced during the
     3.10 cycle that prevents it from working as expected in some
     situations (Tomasz Wilczyński).

   - Fix an error code path in the generic cpuidle driver for DT-based
     systems (Christophe Jaillet).

   - Fix three minor issues in devfreq drivers for Exynos (Arvind Yadav,
     Krzysztof Kozlowski)"

* tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: dt: Add missing 'of_node_put()'
  cpufreq: conservative: Allow down_threshold to take values from 1 to 10
  Revert "cpufreq: schedutil: Reduce frequencies slower"
  PM / devfreq: exynos-ppmu: Staticize event list
  PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
  PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable

Merge branch 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid

Pull HID fix from Jiri Kosina:

 - ifdef-based bandaid for a long-standing issue with HID driver
   matching, avoiding regressions in cases where specific driver is not
   enabled in kernel .config, from Jiri Kosina

* 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: let generic driver yield control iff specific driver has been enabled

Pull media fixes from Mauro Carvalho Chehab:

 - some build dependency issues at CEC core with randconfigs

 - fix an off by one error at vb2

 - a race fix at cec core

 - driver fixes at tc358743, sir_ir and rainshadow-cec

* tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] media/cec.h: use IS_REACHABLE instead of IS_ENABLED
  [media] cec: race fix: don't return -ENONET in cec_receive()
  [media] sir_ir: infinite loop in interrupt handler
  [media] cec-notifier.h: handle unreachable CONFIG_CEC_CORE
  [media] cec: improve MEDIA_CEC_RC dependencies
  [media] vb2: Fix an off by one error in 'vb2_plane_vaddr'
  [media] rainshadow-cec: Fix missing spin_lock_init()
  [media] tc358743: fix register i2c_rd/wr function fix

The driver may sleep under a spin lock, and the function call path is:
i40e_ndo_set_vf_port_vlan (acquire the lock by spin_lock_bh)
  i40e_vsi_remove_pvid
    i40e_vlan_stripping_disable
      i40e_aq_update_vsi_params
        i40e_asq_send_command
          mutex_lock --> may sleep

To fixed it, the spin lock is released before "i40e_vsi_remove_pvid", and
the lock is acquired again after this function.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* acpica-fixes:
  ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
  Revert "ACPICA: Disassembler: Enhance resource descriptor detection"

* pm-cpufreq:
  cpufreq: conservative: Allow down_threshold to take values from 1 to 10
  Revert "cpufreq: schedutil: Reduce frequencies slower"

* pm-cpuidle:
  cpuidle: dt: Add missing 'of_node_put()'

* pm-devfreq:
  PM / devfreq: exynos-ppmu: Staticize event list
  PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
  PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable

Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited.  This was broken by
commit c0303efe ("net: reduce cycles spend on ICMP replies that
gets rate limited").

An ICMP response will usually be routed back-out the same incoming
interface.  Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback.  In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow().  Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").

This seems to fix the reproducer given by Florian.  While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).

Fixes: c0303efe ("net: reduce cycles spend on ICMP replies that gets rate limited")
Reported-by: NFlorian Weimer <fweimer@redhat.com>
Reported-by: N"H.J. Lu" <hjl.tools@gmail.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I'm reviewing static checker warnings where we do ERR_PTR(0), which is
the same as NULL.  I'm pretty sure we intended to return ERR_PTR(-EINVAL)
here.  Sometimes these bugs lead to a NULL dereference but I don't
immediately see that problem here.

Fixes: 71d0ed70 ("net/act_pedit: Support using offset relative to the conventional network headers")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update ->ndo_change_mtu() callback comment to remove text
about returning error in case of undefined callback. This
change makes the comment match the existing code behavior.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Laura reported a sleep-in-atomic kernel warning inside
tcf_act_police_init() which calls gen_replace_estimator() with
spinlock protection.

It is not necessary in this case, we already have RTNL lock here
so it is enough to protect concurrent writers. For the reader,
i.e. tcf_act_police(), it needs to make decision based on this
rate estimator, in the worst case we drop more/less packets than
necessary while changing the rate in parallel, it is still acceptable.
Reported-by: NLaura Abbott <labbott@redhat.com>
Reported-by: NNick Huber <nicholashuber@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Verify that the caller-provided sockaddr structure is large enough to
contain the sa_family field, before accessing it in the connect()
handler of the AF_CAIF socket. Since the syscall doesn't enforce a minimum
size of the corresponding memory region, very short sockaddrs (zero or one
byte long) result in operating on uninitialized memory while referencing
sa_family.
Signed-off-by: NMateusz Jurczyk <mjurczyk@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are two batman-adv bugfixes:

 - fix rx packet counters for local ARP replies, by Sven Eckelmann

 - fix memory leaks for unicast packetes received from another gateway
   in bridge loop avoidance, by Andreas Pape
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Some fixes:
 * Avi fixes some fallout from my mac80211 RX flags changes
 * Emmanuel fixes an issue with adhering to the spec, and
   an oversight in the SMPS management code
 * Jason's patch makes mac80211 use constant-time memory
   comparisons for message authentication, to avoid having
   potentially observable timing differences
 * my fix makes mac80211 set the basic rates bitmap before
   the channel so the next update to the driver has more
   consistent data - this required another rework patch to
   remove some useless 5/10 MHz code that can never be hit
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when dumping a context data only word number '1' is read for the
entire context.

Fixes: c965db44 ("qed: Add support for debug data collection")
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: NPetr Kloc <petr_kloc@yahoo.com>
Reported-by: NTeemu Likonen <tlikonen@iki.fi>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 90eff909 ("net: phy: Allow splitting MDIO
bus/device support from PHYs") we could create a configuration where
MDIO_DEVICE=y and PHYLIB=m which leads to the following undefined
references:

 drivers/built-in.o: In function `thunder_mdiobus_pci_remove':
>> mdio-thunder.c:(.text+0x2a212f): undefined reference to
>> `mdiobus_unregister'
>> mdio-thunder.c:(.text+0x2a2138): undefined reference to
>> `mdiobus_free'
   drivers/built-in.o: In function `thunder_mdiobus_pci_probe':
   mdio-thunder.c:(.text+0x2a22e7): undefined reference to
`devm_mdiobus_alloc_size'
   mdio-thunder.c:(.text+0x2a236f): undefined reference to
`of_mdiobus_register'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Fixes: 90eff909 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's already added by pr_fmt so remove the explicit use.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrey reported a use-after-free in add_grec():

        for (psf = *psf_list; psf; psf = psf_next) {
		...
                psf_next = psf->sf_next;

where the struct ip_sf_list's were already freed by:

 kfree+0xe8/0x2b0 mm/slub.c:3882
 ip_mc_clear_src+0x69/0x1c0 net/ipv4/igmp.c:2078
 ip_mc_dec_group+0x19a/0x470 net/ipv4/igmp.c:1618
 ip_mc_drop_socket+0x145/0x230 net/ipv4/igmp.c:2609
 inet_release+0x4e/0x1c0 net/ipv4/af_inet.c:411
 sock_release+0x8d/0x1e0 net/socket.c:597
 sock_close+0x16/0x20 net/socket.c:1072

This happens because we don't hold pmc->lock in ip_mc_clear_src()
and a parallel mr_ifc_timer timer could jump in and access them.

The RCU lock is there but it is merely for pmc itself, this
spinlock could actually ensure we don't access them in parallel.

Thanks to Eric and Long for discussion on this bug.
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Getting the device version out of the driver really aids debugging.
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes uninitialized symbol warning that
got introduced by the following commit
773fc8f6 ("net: rps: send out pending IPI's on CPU hotplug")
Signed-off-by: NAshwanth Goli <ashwanth@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are many situations where generic HID driver provides some basic level
of support for certain device, but later this support (usually by implementing
vendor-specific extensions of HID protocol) is extended and the support moved
over to a separate (usually per-vendor) specific driver.

This might bring a rather unpleasant suprise for users, as all of a sudden
there is a new config option they have to enable in order to get any support
for their device whatsoever, although previous kernel versions provided basic
support through the generic driver. Which is rightfully seen as a regression.

Fix this by including the entry for a particular device in
hid_have_special_driver[] iff the specific config option has been specified,
and let generic driver handle the device otherwise.
Also make the behavior of hid_scan_report() (where the same decision is being
taken on a per-report level) consistent.

While at it, reshuffle the hid_have_special_driver[] a bit to restore the
alphabetical ordering (first order by config option, and within those
sections order by VID).

This is considered a short-term solution, before generic way of giving
precedence to special drivers and falling back to generic driver is
figured out.

While at it, fixup a missing entry for GFRM driver; thanks to Hans de Geode for
spotting this (and for discovering a few issues in the conversion).
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

mac80211 allows to modify the SMPS state of an AP both,
when it is started, and after it has been started. Such a
change will trigger an action frame to all the peers that
are currently connected, and will be remembered so that
new peers will get notified as soon as they connect (since
the SMPS setting in the beacon may not be the right one).

This means that we need to remember the SMPS state
currently requested as well as the SMPS state that was
configured initially (and advertised in the beacon).
The former is bss->req_smps and the latter is
sdata->smps_mode.

Initially, the AP interface could only be started with
SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF
always. Later, a nl80211 API was added to be able to start
an AP with a different AP mode. That code forgot to update
bss->req_smps and because of that, if the AP interface was
started with SMPS_DYNAMIC, we had:
   sdata->smps_mode = SMPS_DYNAMIC
   bss->req_smps = SMPS_OFF

That configuration made mac80211 think it needs to fire off
an action frame to any new station connecting to the AP in
order to let it know that the actual SMPS configuration is
SMPS_OFF.

Fix that by properly setting bss->req_smps in
ieee80211_start_ap.

Fixes: f6993174 ("mac80211: set smps_mode according to ap params")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: NJason A. Donenfeld <Jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When mac80211 changes the channel, it also calls into the driver's
bss_info_changed() callback, e.g. with BSS_CHANGED_IDLE. The driver
may, like iwlwifi does, access more data from bss_info in that case
and iwlwifi accesses the basic_rates bitmap, but if changing from a
band with more (basic) rates to one with fewer, an out-of-bounds
access of the rate array may result.

While we can't avoid having invalid data at some point in time, we
can avoid having it while we call the driver - so set up all the
data before configuring the channel, and then apply it afterwards.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195677Reported-by: NJohannes Hirte <johannes.hirte@datenkhaos.de>
Tested-by: NJohannes Hirte <johannes.hirte@datenkhaos.de>
Debugged-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need for the station MLME code to handle bitrates for 5
or 10 MHz channels when it can't ever create such a configuration.
Remove the unnecessary code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the driver reports the rx timestamp at PLCP start, mac80211 can
only handle legacy encoding, but the code checks that the encoding
is not legacy. Fix this.

Fixes: da6a4352 ("mac80211: separate encoding/bandwidth from flags")
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a peer sends a BAR frame with PM bit clear, we should
not modify its PM state as madated by the spec in
802.11-20012 10.2.1.2.

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Pull Xtensa fixes from Max Filippov:

 - don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
   assignment when it's hardware IRQ # is 0 and the kernel is built w/o
   device tree support

 - reduce reservation size for double exception vector literals from 48
   to 20 bytes: fixes build on cores with small user exception vector

 - cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
   seq_puts instead of seq_printf in c_show.

* tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: don't use linux IRQ #0
  xtensa: reduce double exception literal reservation
  xtensa: ISS: Use kmalloc_array() in simdisk_init()
  xtensa: Use seq_puts() in c_show()

Pull s390 fixes from Martin Schwidefsky:

 - A fix for KVM to avoid kernel oopses in case of host protection
   faults due to runtime instrumentation

 - A fix for the AP bus to avoid dead devices after unbind / bind

 - A fix for a compile warning merged from the vfio_ccw tree

 - Updated default configurations

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: update defconfig
  s390/zcrypt: Fix blocking queue device after unbind/bind.
  s390/vfio_ccw: make some symbols static
  s390/kvm: do not rely on the ILC on kvm host protection fauls