Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 22 12月, 2011 1 次提交
  3. 21 12月, 2011 1 次提交
  5. 20 12月, 2011 6 次提交
  7. 19 12月, 2011 11 次提交
  9. 18 12月, 2011 6 次提交
  11. 17 12月, 2011 11 次提交
  13. 16 12月, 2011 2 次提交
  15. 15 12月, 2011 2 次提交
    • J
      [SCSI] fcoe: fix fcoe in a DCB environment by adding DCB notifiers to set skb priority · 6f6c2aa3
      由 john fastabend 提交于 
      Use DCB notifiers to set the skb priority to allow packets
to be steered and tagged correctly over DCB enabled drivers
that setup traffic classes.

This allows queue_mapping() routines to be removed in these
drivers that were previously inspecting the ethertype of
every skb to mark FCoE/FIP frames.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
      6f6c2aa3
    • A
      PCI: Set device power state to PCI_D0 for device without native PM support · b51306c6
      由 Ajaykumar Hotchandani 提交于 
      During test of one IB card with guest VM, found that, msi is not
initialized properly.

It turns out __write_msi_msg will do nothing if device current_state is
not PCI_D0.  And, that pci device does not have pm_cap in guest VM.

There is an error in setting of power state to PCI_D0 in
pci_enable_device(), but error is not returned for this.  Following is
code flow:

pci_enable_device() -->   __pci_enable_device_flags() -->
do_pci_enable_device() -->   pci_set_power_state() -->
__pci_start_power_transition()

We have following condition inside __pci_start_power_transition():
         if (platform_pci_power_manageable(dev)) {
                 error = platform_pci_set_power_state(dev, state);
                 if (!error)
                         pci_update_current_state(dev, state);
         } else {
                 error = -ENODEV;
                 /* Fall back to PCI_D0 if native PM is not supported */
                 if (!dev->pm_cap)
                         dev->current_state = PCI_D0;
         }

Here, from platform_pci_set_power_state(), acpi_pci_set_power_state() is
getting called and that is failing with ENODEV because of following
condition:

         if (!handle || ACPI_SUCCESS(acpi_get_handle(handle, "_EJ0",&tmp)))
                 return -ENODEV;

Because of that, pci_update_current_state() is not getting called.

With this patch, if device power state can not be set via
platform_pci_set_power_state and that device does not have native pm
support, then PCI device power state will be set to PCI_D0.

-v2: This also reverts 47e9037a, as it's
     not needed after this change.
Acked-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ajaykumar Hotchandani<ajaykumar.hotchandani@oracle.com>
Signed-off-by: Yinghai Lu<yinghai.lu@oracle.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
      b51306c6