Always use software checksumming, since the hardware does not have any
checksum offload support.
This significantly improves local TCP tx performance.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This improves performance for routing and local rx
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ARM SoCs with bgmac Ethernet hardware we don't have any normal PHY.
There is always a switch attached but it's not even controlled over MDIO
like in case of MIPS devices.
We need a fixed PHY to be able to send/receive packets from the switch.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Northstar (Broadcom's ARM architecture) we need to manually enable
all cores. Code for that is already in place, but the condition for it
was wrong.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the normal {} instead of a macro to terminate an array.

Remove the macro too.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi should get registered before the netdev and not after.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bgmac_mii_register() and register_netdev() both return appropriate error
codes for the failures they would encounter, propagate this error code
instead of overriding the value with -ENOTSUPP which is not the correct
error code to return.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes some typos found by Sergei.
Reported-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the Northstar SoC. This SoC does not have a PMU in
bcma and no register on it should be called. In addition it support 2.5
GBit/s Ethernet to the PHY.

This GMAC core is not fully working there are still problems with the
DMA controller.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the Northstar SoC (BCM4707 and BCM53018) we have to enable all GMAC
cores when we just want to use on. We iterate over all the cores and
activate them.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BGMAC_CMDCFG_SR register is at a different position on core rev >= 4
We do not know where this register is on a rev 5 or higher core, I have
newer seen such a core.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DMA controller used in the device supported by GMAC with core rev
>= 4 has some new options which are now set to the default values used
in the Broadcom SDK.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This works pretty much the same way, so avoid duplicating the code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this bgmac_adjust_link didn't know it should re-initialize MAC
state. This led to the MAC not working after if down & up routine.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I've realized that I need to call ethtool command to get Ethernet
working after booting. Ex call: ethtool -s eth0 autoneg on
It was fixing Ethernet even if auto-negotiation was already on.

Adding calls to phy_start and phy_stop look like a real solution.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were already registering MDIO bus, but we were not connecting bgmac
to the PHY. Add proper call and implement adjust link function to switch
MAC into requested state.
At the same time it's possible to drop our internal PHY management.
This is a "standard" PHY, so the "Generic PHY" driver works perfectly
fine with this. Don't duplicate the code.
Finally make use of phy_ethtool_[gs]set functions instead implementing
them from scratch.

This change was successfully tested on BCM5357. I was able to
autonegotiate 1000Mb/s full duplex, as well as force any of the
10/100/1000 half/full modes.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Copying whole packets with skb_copy_from_linear_data_offset is a pretty
bad idea. CPU was spending time in __copy_user_common and network
performance was lower. With the new solution iperf-measured speed
increased from 116Mb/s to 134Mb/s.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't update the slot in "bgmac_dma_rx_skb_for_slot" unless both the
skb alloc and dma mapping are successful; and free the newly allocated
skb if a dma mapping error occurs.  This relieves the caller of the need
to deduce/execute the appropriate cleanup action required when an error
occurs.
Signed-off-by: NNathan Hintz <nlhintz@hotmail.com>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cleans code a bit and will be useful when allocating buffers in
other places (like RX path, to avoid skb_copy_from_linear_data_offset).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes it possible to use some more advanced queuing
techniques with this driver.

When multi queue support will be added some changes to Byte Queue
handling is needed.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.

Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.

Other trivial changes around these removals:

Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not include the frame check sequence when adding the skb to
netif_receive_skb(). This causes problems when this interface was
bridged to a wifi ap and a big package should be forwarded from this
Ethernet driver through a bride to the wifi client.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were using the same variable for iterating two nested loops.
Reported-by: NTijs Van Buggenhout <tvb@able.be>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch I get many unaligned access warnings per packet,
this patches fixes them all. This should improve performance on some
systems like mips.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The specs prescribe an immediate read of the interrupt mask after
disabling interrupts.  This patch updates the driver to match the
specs.
Signed-off-by: NNathan Hintz <nlhintz@hotmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some callers may want to know if PHY write succeed. Also make PHY
functions static, they are not exported anywhere.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The last (bool) parameter in bgmac_cmdcfg_maskset says if the write
should be made, even if value didn't change. Currently driver doesn't
match the specs about (not) forcing some changes. This makes it follow
them.
Reported-by: NNathan Hintz <nlhintz@hotmail.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds check for a valid Ethernet MAC address and in case it is not,
it will generate a valid random one, such that the adapter is still
usable.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing the device from or to promisc mode this only affects the
device after the device is bought up the next time. For bridging it is
needed to change the device to promisc mode while it is up, which is
possible with this patch.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic implementation just changes the netdev struct and does not
write the new mac address to the hardware or issues some command to do
so.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>