Introduce token tracing support in mt7615_mac_tx_free routine
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mac_txdone tracepoint in common code in order to
be reused by mt7603 and mt7615 drivers
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move dev_irq tracepoint in common code in order to be reused by mt7603
and mt7615 drivers
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add a get_stats() callback for mib statistics.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Update per-phy mib counters every 500ms.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This adds a get_tsf() callback for ibss.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add a set_antenna callback to setup per phy tx/rx streams.
Signed-off-by: NShayne Chen <shayne.chen@mediatek.com>
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

No need to send both MCU_EXT_CMD_SET_RX_PATH and MCU_EXT_CMD_CHANNEL_SWITCH
together to MCU.

Split them out by passing the proper command in the corresponding flow.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

MT7615 supports dual-wiphy which means that it can run on 2.4G and 5GHz
channels simultaneously, and driver should configure each band.

Add missing register settings, and refine band related definitions to
avoid duplicate codes.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Fix the following compilation warning in mt76_eeprom_override routine
when CONFIG_OF is not set and label 'out' is not actually used

drivers/net/wireless/mediatek/mt76/eeprom.c: In function ‘mt76_eeprom_override’:
drivers/net/wireless/mediatek/mt76/eeprom.c:100:1: warning: label ‘out’ defined but not used [-Wunused-label]
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Initialize brightness_set and blink_set callbacks to
mt7615_led_set_brightness and mt7615_led_set_blink in order to enable
LED support in mt7615 driver
Tested-by: NDeng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

During the cleanup of the aggregation session, a rx handler (or release timer)
on another CPU might still hold a pointer to the reorder buffer and could
attempt to release some packets.
Clearing pointers during cleanup avoids a theoretical use-after-free bug here.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Before extracting the tid out of the packet, check if it was qos-data.
Only accept tid values 0-7
Also, avoid accepting the hardware queue as skb queue mapping, it could
lead to an overrun. Instead, derive the hardware queue from the tid number,
in order to avoid issues with packets being filtered multiple times.
This also fixes a mismatch between hardware and software queue indexes.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

MCU_EXT_CMD_EFUSE_BUFFER_MODE needs more time on initialization, and
with only 10 seconds it sometimes runs into timeouts.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Read measurements every 100 ms and build a simple moving average
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Fix default CFEND_RATE and replace hardcode values.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

We do not call mt76x02_mac_set_beacon() with NULL skb any longer and
we do not need to return error value.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

With current implementation we do not cleanup beacon memory, so is not
needed to call mt76x02_mac_set_beacon() with NULL skb.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

For transferring data over USB the optimal size is endpoint maxpacket.
For my hardware maxpaket for control endpoint is 64 bytes and changing
to this value from 128 bytes further shorten TBTT work time from
3ms to 1ms.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This patch enables channel switch support on mt76 usb interfaces.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use larger batches for usb copy to speed this operation up. Otherwise it
would be too slow for copying new beacons or broadcast frames over usb.
Assure, that always a multiple of 4 Bytes is copied, as outlined in
850e8f6f "mt76: round up length on mt76_wr_copy" from Felix Fietkau.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This patch removes a mt76_wr_copy call from the beacon path to hw.
The skb which is used in this place gets therefore build with txwi
inside its data. For mt76 usb drivers, this saves one synchronuous
copy call over usb, which lets the beacon work complete faster.

In mmio case, there is not enough headroom to put the txwi into the
skb, it is therefore using an additional mt76_wr_copy, which is fast
over mmio. Thanks Stanislaw for pointing this out.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

On adding vifs the idx can become 1 + (7 & 7) = 8 for APs.
Check against that, as only AP vif idx 0-7 is possible.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Sending beacons to the hardware always happens in batches. In order to
speed up beacon processing on usb devices, this patch splits out common
code an calls it only once.

Beacons are sequentially written into the beacon memory area, by
tracking its usage with the dev->beacon_data_count. For MBSS support
and buffered traffic dev->beacon_data_count is used to create the bypass
mask.

The code is also adapted for the mmio part of the driver, but should not
have any performance implication there.

MBSS tests were performed with AVM AC860 USB NIC with temporary support
for 5 BSS'. Different combinations of active vifs were created and
brought up. Afterwards connection and data transfer was tested for the
announced BSS'.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

mt76 hw does not send beacons from beacon slots, if the corresponding
bitmask is set accordingly. Therefore we can omit clearing the beacon
memory. Clearing uses many usb calls, if usb drivers are used. These
calls unnecessarily slow down the beacon tasklet. Thanks to Stanislaw
Gruzska for pointing this out.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Before this patch, mt76 handled rx traffic for all TIDs equally,
when released from reorder buffer early. This patch uses an AC specific
reorder timeout, in order to release partial aggregated frames for video
ACs earlier. Voice ACs are currently not aggregated (thanks to Felix for
this hint). For example, ath10k also uses AC specific reorder timeouts
(reported by firmware in that case).
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add the capability to configure acktimeout for mt7615 driver. Moreover
configure slottime according to the value provided by mac80211
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Set 0 as minimum configurable value for coverage_class since mt76 does
not support dynack
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Fix coverage_class type in mt76x02_dev data structure since
coverage_class can be negative to enable dynack (just supported by
ath9k). Set 0 as minimum value for coverage_class

Fixes: 7bc04215 ("mt76: add driver code for MT76x2e")
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Print fw_ver and build_date members of struct mt7615_fw_trailer
similarly to what appears in the output of 'dmesg' when the MCU firmware
is loaded.
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Some compilers (tested with 4.8.5 from CentOS 7) fail properly process
FIELD_GET inside an inline function, which ends up in a BUILD_BUG_ON.
Convert inline function to a macro.

Fixes commit bf92e768 ("mt76: mt7615: add support for per-chain
signal strength reporting")
Reported in https://lkml.org/lkml/2019/9/21/146Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NPablo Greco <pgreco@centosproject.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Introduce big-endian property to specify mtd radio partition endianness
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

mt76x0e users reported some devices (e.g TP-Link Archer VR200v) have
been flashed with big endian radio partition. Add the possibility to
specify eeprom endianness using big-endian dts property and in case
covert eeprom data in little endian
Tested-by: NKevin Schmidt <kevin.patrick.schmidt@googlemail.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Reset MT_MIB_STAT_CCA after channel switch since it is used to track busy
time starting from 'commit dcff8d4d ("mt76: mt7603: switch to a
different counter for survey busy time")'
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Make sure the MAC address is checked before function returns.

If CONFIG_OF is set and the device node is null, the function will
return directly, and an invalid MAC address will not be checked.
Signed-off-by: NShayne Chen <shayne.chen@mediatek.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Fixes potential RCU issues and avoids calling ieee80211_rx_napi with softirq
enabled.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

To avoid having the hardware potentially write to memory behind stale
descriptors, set the dma-done flag on all of them before cleaning up
allocated rx buffers
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

The MT7615 firmware needs to know the association id at creation time,
which is unavailable during the transition from notexist to none in
.sta_state.
This can cause a number of issues, probably also breaking powersave
support.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>