We're adding i2c tunneling to the list of things that goes over
cros_ec.  i2c tunneling can be slooooooow, so increase our deadline to
100ms to account for that.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Tested-by: NAndrew Bresticker <abrestic@chromium.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The cros_ec_spi transfer had two problems with its timeout code:

1. It looked at the timeout even in the case that it found valid data.
2. If the cros_ec_spi code got switched out for a while, it's possible
   it could get a timeout after a single loop.  Let's be paranoid and
   make sure we do one last transfer after the timeout expires.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Tested-by: NAndrew Bresticker <abrestic@chromium.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The main transfer function for cros_ec_spi can be called by more than
one client at a time.  Make sure that those clients don't stomp on
each other by locking the bus for the duration of the transfer
function.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Tested-by: NAndrew Bresticker <abrestic@chromium.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

To avoid spamming the EC we calculate the time between the previous
transfer and the current transfer and force a delay if the time delta
is too small.

However, a small miscalculation causes the delay period to be
far too short. Most noticably this impacts commands with a long
turnaround time such as EC firmware reads and writes.
Signed-off-by: NDavid Hendricks <dhendrix@chromium.org>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Tested-by: NAndrew Bresticker <abrestic@chromium.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Some output configurations can require a 50Mhz SYSCLK which requires
DCVDD to be 1.8V. This patch adds the registers necessary for
supporting this operational mode.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Currently, MICVDD only binds because it is both the regulator name and
the consumer name and we will always match against the regulator name
regardless of the consumer device. If the regulator was renamed using
the init_data ASoC will no longer be able to locate the supply, as it
will be looking on the CODEC device where as the MICVDD consumer is on
the Arizona device. Add a mapping as we do for the other regulators.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

mfd_add_devices() expects array of struct mfd_cell to be const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds a driver for the Atmel Microcontroller found on the
iPAQ h3xxx series. This device handles some keys, the
touchscreen, and the battery monitoring.

This is a port of a driver from handhelds.org 2.6.21 kernel,
written by Alessandro Gardich based on Andrew Christians
original HAL-driver. It has been heavily cleaned and
converted to mfd-core by Dmitry Artamonow and rewritten
again for the v3.x series kernels by Linus Walleij,
bringing back some of the functionality lost from Andrew's
original driver.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAlessandro Gardich <gremlin@gremlin.it>
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

commit df73de9b ("mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON
is not enabled") introduced fallbacks for APIs, but missed out on adding
the header file. This would work only if linux/err.h is also included
in the source code from where this file is included. It would be better
to include linux/err.h in file to remove possible build errors.

Without this patch, we get following and similar build errors if this
header file is included in some source file and CONFIG_MFD_SYSCON is
not enabled.

include/linux/mfd/syscon.h: In function ‘syscon_node_to_regmap’:
include/linux/mfd/syscon.h:30:2: error: implicit declaration of function ‘ERR_PTR’ [-Werror=implicit-function-declaration]
  return ERR_PTR(-ENOSYS);
  ^
include/linux/mfd/syscon.h:30:18: error: ‘ENOSYS’ undeclared (first use in this function)
  return ERR_PTR(-ENOSYS);
                  ^
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The PRCM (Power/Reset/Clock Management) block exposes several subdevices
in different subsystems (clk, reset ...)

Add basic support for the PRCM unit with clk (AR100, AHB0, and APB0 clks)
and reset controller subdevices.

Other subdevices might be added later (if needed).
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Document DT bindings of the PRCM (Power/Reset/Clock Management) unit.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

mfd_add_devices() expects array of struct mfd_cell to be const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NRoger Tseng <rogerable@realtek.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id may be be const as expected by
of_platform_populate() call.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id may be be const as expected by
of_match_table field.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

mfd_add_devices() expects array of struct mfd_cell to be const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

mfd_add_devices() expects array of struct mfd_cell to be const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NMilo Kim <milo.kim@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id should be const as expected by both
of_match_table field and of_match_device() call.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id may be be const as expected by both
of_match_table field and of_match_node() call.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

mfd_add_devices() expects array of struct mfd_cell to be const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id may be be const as expected by both
of_match_table field and of_match_node() call.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

mfd_add_devices() expects array of struct mfd_cell to be const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id may be be const as expected by
of_match_table field.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id may be be const as expected by
of_match_table field.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The kempld_devs (array of mfd_cells) can be safely made const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NKevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id may be be const as expected by both
of_match_table field and of_match_node() call.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Array of struct of_device_id may be be const as expected by
of_match_table field.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch removes platform data usage for codec and touchscreen
when driver is used with devicetree.
This fixes possible "null pointer dereference" error if DTS uses
"fsl,mc13xxx-uses-codec" or "fsl,mc13xxx-uses-touch" options.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

When the MCLK is 19.2 or 38.4 MHz the HPPLL need to be enabled and can be
put in bypass mode.
This will fix HPPLL use on boards with 19.2MHz mclk.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch introduces the preliminary support for PMICs X-Powers AXP202
and AXP209. The AXP209 and AXP202 are the PMUs (Power Management Unit)
used by A10, A13 and A20 SoCs and developed by X-Powers, a sister company
of Allwinner.

The core enables support for two subsystems:
- PEK (Power Enable Key)
- Regulators
Signed-off-by: NCarlo Caione <carlo@caione.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

If we pass syscon device node itself as first parameter to this function
there is no need to parse and find syscon device node. So by allowing
"property" parameter as NULL allow syscon_regmap_lookup_by_phandle to
consider passed argument "np" itself as a syscon device node "syscon_np".
This will help us in avoiding addition of "syscon" property in a device node
which points back to same device node in device tree.
Signed-off-by: NPankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The pm8xxx read/write wrappers are no longer necessary now that
all the sub-device drivers are using the regmap API. Remove it.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

During suspend the IRQ should be disabled even if this is not a wakeup
source. This is a proper way of fixing the IRQ handling issue during
resume (IRQ handler fails because I2C bus did not resume yet).

When device is suspended and max14577 interrupt is signaled the irq chip
will try to handle it regardless of wakeup source. Device could be woken
up by different IRQ but still the IRQ handler will try to read the
registers over I2C bus and fail because I2C bus won't be ready yet:
	max14577 2-0025: Failed to read IRQ status: -5
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

During suspend the IRQ should be disabled even if this is not a wakeup
source. This is a proper way of fixing the IRQ handling issue during
resume (IRQ handler fails because I2C bus did not resume yet).

When device is suspended and sec-core interrupt is signaled the irq chip
will try to handle it regardless of wakeup source. Device could be woken
up by different IRQ but still the IRQ handler will try to read the
registers over I2C bus and fail because I2C bus won't be ready yet.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The device type was stored in sec_pmic_dev state container twice:
 - unsigned long type (initialized from of_device_id or i2c_device_id)
 - int device_type (initialized as above or from board files when there
   is no DTS)

The 'type' field was never used outside of probe so it can be safely
removed.

Change also the device_type in sec_pmic_dev and sec_platform_data to
unsigned long to avoid any casts.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>