There is no need to terminate transfer in the __dma_rx_complete() since it's
called at the end of transfer. Special case when serial timeout occurs is
handled separately where we have to terminate transfer.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

By using devm_request_irq() we can have a shorter and cleaner code.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

By using devm_clk_get() we can have a shorter and cleaner code.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

By using devm_kzalloc() we can have a shorter and cleaner code.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of jumping to the 'out' label, let's return the error immediately, which
makes the code shorter and cleaner.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Because the OMAP3 UART ignores MCR[1] (RTS) in autoRTS mode, autoRTS
mode must not be enabled unless RTS is set (or port->mctrl & TIOCM_RTS,
which is equivalent).

Fixes premature raising of RTS in omap_8250_set_termios() -- RTS was
raised even before UART mode was selected.
Fixes raise of RTS after port has been shutdown; omap_8250_pm() re-enabled
RTS after omap_8250_shutdown().

Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS
mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either
the serial core or userspace to manually flow control the sender.

Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.

Note that the OMAP3 UART provides no mechanism for switching from
autoRTS mode without corrupting incoming data; to access the
necessary register, the line control settings must be set to 8-e-2
and thus any data received during that time will be interpreted with
those settings. This corruption has been observed in practice.

Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Trivial fixes for omap-serial.
Signed-off-by: NPavel Machek <pavel@ucw.cz>

index 18c30ca..f43ed2c 100644
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch invokes add_preferred_console() with ttyS based on ttyO
arguments if the user didn't specify it on its own. This ensures that
the user will see the kernel booting on his serial console in case he
forgot to update the command line.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current output of the device probing looks like this:

ColdFire internal UART serial driver
(NULL device *): ttyS0 at MMIO 0xfc060000 (irq = 90, base_baud = 5208333) is a ColdFire UART
console [ttyS0] enabled
(NULL device *): ttyS1 at MMIO 0xfc064000 (irq = 91, base_baud = 5208333) is a ColdFire UART
(NULL device *): ttyS2 at MMIO 0xfc068000 (irq = 92, base_baud = 5208333) is a ColdFire UART

Fix the port device linkage at probing time so that the device name is
printed out properly, and not "(NULL device *)".
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Trivially fix the following compile time warnings:

  CC      drivers/tty/serial/mcf.o
drivers/tty/serial/mcf.c: In function ‘mcf_set_termios’:
drivers/tty/serial/mcf.c:201:19: warning: unused variable ‘pp’
drivers/tty/serial/mcf.c: In function ‘mcf_config_rs485’:
drivers/tty/serial/mcf.c:444:19: warning: unused variable ‘pp’
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Change my email contact address from the obsolete gerg@snapgear.com to
gerg@uclinux.org.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The 8250_omap serial driver is a new user of CONFIG_PM_RUNTIME.

However, after commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so
#ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to
depend on CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM in 8250_omap.c.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/tty/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make the serial_mctrl_gpio driver the first user of the new gpiod_set_array
function, which is now available in the linux-gpio devel tree.
All modem control output signals are now set simultaneously.
Signed-off-by: NRojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Both uart_handle_dcd_change() and uart_handle_cts_change() require a
port lock to be held and will emit a warning when lockdep is enabled.
Held corresponding lock.

This fixes the following warnings:

------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/serial_core.c:2760 uart_handle_dcd_change+0xc8/0xf8()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc5+ #26
[<c000dff8>] (unwind_backtrace) from [<c000bc70>] (show_stack+0x10/0x14)
[<c000bc70>] (show_stack) from [<c00192ac>] (warn_slowpath_common+0x6c/0x8c)
[<c00192ac>] (warn_slowpath_common) from [<c00192e8>] (warn_slowpath_null+0x1c/0x24)
[<c00192e8>] (warn_slowpath_null) from [<c0182984>] (uart_handle_dcd_change+0xc8/0xf8)
[<c0182984>] (uart_handle_dcd_change) from [<c018625c>] (serial_pxa_irq+0x268/0x3b0)
[<c018625c>] (serial_pxa_irq) from [<c004d0d4>] (handle_irq_event_percpu+0x50/0x16c)
[<c004d0d4>] (handle_irq_event_percpu) from [<c004d22c>] (handle_irq_event+0x3c/0x5c)
[<c004d22c>] (handle_irq_event) from [<c004f7d0>] (handle_level_irq+0x94/0x118)
[<c004f7d0>] (handle_level_irq) from [<c004ca0c>] (generic_handle_irq+0x20/0x30)
[<c004ca0c>] (generic_handle_irq) from [<c004cbe0>] (__handle_domain_irq+0x38/0x70)
[<c004cbe0>] (__handle_domain_irq) from [<c00085c4>] (ichp_handle_irq+0x24/0x34)
[<c00085c4>] (ichp_handle_irq) from [<c000c7e4>] (__irq_svc+0x44/0x54)
Exception stack(0xc07c7f58 to 0xc07c7fa0)
7f40:                                                       00000001 00000001
7f60: 00000000 20000013 c07c6000 00000000 00000000 c07ce0a4 c07d7798 00000000
7f80: c07e8fb8 0000004c 00000000 c07c7fa0 c0044798 c0009f20 20000013 ffffffff
[<c000c7e4>] (__irq_svc) from [<c0009f20>] (arch_cpu_idle+0x28/0x38)
[<c0009f20>] (arch_cpu_idle) from [<c003c974>] (cpu_startup_entry+0x1b8/0x220)
[<c003c974>] (cpu_startup_entry) from [<c0338c54>] (start_kernel+0x39c/0x40c)
---[ end trace 4c1b7ae03f6d9d30 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/serial_core.c:2791 uart_handle_cts_change+0xa0/0xdc()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Tainted: G        W      3.18.0-rc5+ #26
[<c000dff8>] (unwind_backtrace) from [<c000bc70>] (show_stack+0x10/0x14)
[<c000bc70>] (show_stack) from [<c00192ac>] (warn_slowpath_common+0x6c/0x8c)
[<c00192ac>] (warn_slowpath_common) from [<c00192e8>] (warn_slowpath_null+0x1c/0x24)
[<c00192e8>] (warn_slowpath_null) from [<c018528c>] (uart_handle_cts_change+0xa0/0xdc)
[<c018528c>] (uart_handle_cts_change) from [<c018624c>] (serial_pxa_irq+0x258/0x3b0)
[<c018624c>] (serial_pxa_irq) from [<c004d0d4>] (handle_irq_event_percpu+0x50/0x16c)
[<c004d0d4>] (handle_irq_event_percpu) from [<c004d22c>] (handle_irq_event+0x3c/0x5c)
[<c004d22c>] (handle_irq_event) from [<c004f7d0>] (handle_level_irq+0x94/0x118)
[<c004f7d0>] (handle_level_irq) from [<c004ca0c>] (generic_handle_irq+0x20/0x30)
[<c004ca0c>] (generic_handle_irq) from [<c004cbe0>] (__handle_domain_irq+0x38/0x70)
[<c004cbe0>] (__handle_domain_irq) from [<c00085c4>] (ichp_handle_irq+0x24/0x34)
[<c00085c4>] (ichp_handle_irq) from [<c000c7e4>] (__irq_svc+0x44/0x54)
Exception stack(0xc07c7f58 to 0xc07c7fa0)
7f40:                                                       00000001 00000001
7f60: 00000000 20000013 c07c6000 00000000 00000000 c07ce0a4 c07d7798 00000000
7f80: c07e8fb8 0000004c 00000000 c07c7fa0 c0044798 c0009f20 20000013 ffffffff
[<c000c7e4>] (__irq_svc) from [<c0009f20>] (arch_cpu_idle+0x28/0x38)
[<c0009f20>] (arch_cpu_idle) from [<c003c974>] (cpu_startup_entry+0x1b8/0x220)
[<c003c974>] (cpu_startup_entry) from [<c0338c54>] (start_kernel+0x39c/0x40c)
---[ end trace 4c1b7ae03f6d9d31 ]---
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty_kref_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The functions put_device() and tty_kref_put() test whether their argument
is NULL and then return immediately.
Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 19e2ad6a ("n_tty: Remove overflow
tests from receive_buf() path") moved the increment of read_head into
the arguments list of read_buf_addr(). Function calls represent a
sequence point in C. Therefore read_head is incremented before the
character c is placed in the buffer. Since the circular read buffer is
a lock-less design since commit 6d76bd26
("n_tty: Make N_TTY ldisc receive path lockless"), this creates a race
condition that leads to communication errors.

This patch modifies the code to increment read_head _after_ the data
is placed in the buffer and thus fixes the race for non-SMP machines.
To fix the problem for SMP machines, memory barriers must be added in
a separate patch.
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds suspend/resume support for the of-serial driver
to provide power management support on devices attatched.

The handling may vary since not every of_serial device is
an 8250 port. Currently only 8250 port handling is added
in the suspend/resume function based on the type switch.
Signed-off-by: NJingchang Lu <jingchang.lu@freescale.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NJoseph Lo <josephl@nvidia.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NFlorina Fainelli <f.fainelli@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 2dea53bf.

Turns out to be broken :(

Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 513e4385.

It's broken :(

Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Joseph Lo <josephl@nvidia.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Attempting to use SysRq via the 8250 serial port with spin lock
debugging on on a uniprocessor system results in the following splat:

 SysRq :
 BUG: spinlock trylock failure on UP on CPU#0, swapper/0
  lock: serial8250_ports+0x0/0x8c0, .magic: dead4ead, .owner: swapper/0, .owner_cpu: 0
 CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc4+ #37
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
  ffffffff8245ba00 ffffffff81628b28 ffffffff812c8d27 ffffffff81628b48
  ffffffff8106812e ffffffff8245ba00 ffffffff814e22ed ffffffff81628b68
  ffffffff810681a6 0000000000000000 0000000000000000 ffffffff81628b88
 Call Trace:
  <IRQ>  [<ffffffff812c8d27>] dump_stack+0x19/0x1b
  [<ffffffff8106812e>] spin_dump+0x7e/0xd0
  [<ffffffff810681a6>] spin_bug+0x26/0x30
  [<ffffffff8106843c>] do_raw_spin_trylock+0x4c/0x60
  [<ffffffff812cdb1d>] _raw_spin_trylock+0x1d/0x60
  [<ffffffff812336d8>] serial8250_console_write+0x68/0x190
  [<ffffffff811eb0b0>] ? sprintf+0x40/0x50
  [<ffffffff8106ab5e>] call_console_drivers.constprop.11+0x9e/0xf0
  [<ffffffff8106b276>] console_unlock+0x3e6/0x490
  [<ffffffff8106b595>] vprintk_emit+0x275/0x530
  [<ffffffff812c869a>] printk+0x4d/0x4f
  [<ffffffff8121e612>] __handle_sysrq+0x62/0x1b0
  [<ffffffff8121e5b5>] ? __handle_sysrq+0x5/0x1b0
  [<ffffffff8121ebc6>] handle_sysrq+0x26/0x30
  [<ffffffff81233157>] serial8250_rx_chars+0x1d7/0x250
  [<ffffffff812338bb>] serial8250_handle_irq+0x7b/0x90
  [<ffffffff812338f3>] serial8250_default_handle_irq+0x23/0x30
  [<ffffffff812318b3>] serial8250_interrupt+0x63/0xe0
  [<ffffffff8106d80e>] handle_irq_event_percpu+0x4e/0x200
  [<ffffffff8106da01>] handle_irq_event+0x41/0x70
  [<ffffffff810701ee>] ? handle_edge_irq+0x1e/0x110
  [<ffffffff8107026e>] handle_edge_irq+0x9e/0x110
  [<ffffffff810041c2>] handle_irq+0x22/0x40
  [<ffffffff812d096e>] do_IRQ+0x4e/0xf0
  [<ffffffff812cf4ed>] common_interrupt+0x6d/0x6d
  <EOI>  [<ffffffff8100acbf>] ? default_idle+0x1f/0xd0
  [<ffffffff8100acbd>] ? default_idle+0x1d/0xd0
  [<ffffffff8100b61f>] arch_cpu_idle+0xf/0x20
  [<ffffffff8105c1db>] cpu_startup_entry+0x25b/0x360
  [<ffffffff812c726e>] rest_init+0xbe/0xd0
  [<ffffffff816a4dcb>] start_kernel+0x339/0x346
  [<ffffffff816a4495>] x86_64_start_reservations+0x2a/0x2c
  [<ffffffff816a4589>] x86_64_start_kernel+0xf2/0xf6
 HELP : loglevel(0-9) reboot(b) crash(c) show-all-locks(d) te...

Before ebade5e8 ("serial: 8250: Clean up the locking for -rt")
this was handled by not even attempting to try the lock if port->sysrq,
since it is known to be taken by the interrupt handler; see
https://bugzilla.kernel.org/show_bug.cgi?id=6716#c1.  Restore that
behavior.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since most drivers interpret UPIO_MEM32 to mean "little-endian" and use
readl/writel to access the registers, add a parallel UPIO_MEM32BE to
request the use of big-endian MMIO accessors (ioread32be/iowrite32be).
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Hardcoded FIFO size can cause hardware performance limitation.
Using real size value provides better FIFO usage.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If we have fifosize set in driver data we prefer to use it instead of default
fifosize value (which is always 16). If there is defined fifosize for particular
serial we prefer to use it, otherwise we use value from info, which is
common for all serials on given platform.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Split lines longer than 80 chars and remove unnecessary whitespaces.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds waiting until transmit buffer and shifter will be empty
before clock disabling.

Without this fix it's possible to have clock disabled while data was
not transmited yet, which causes unproper state of TX line and problems
in following data transfers.

Cc: <stable@vger.kernel.org> # v2.6.26+
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Return a negative error code on failure.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty break and error flags are not bit masks so do not to use bitwise
OR when assigning them.

Note that there is no functional change due to the if-else construct and
flag having been initialised to zero (TTY_NORMAL).
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The original driver fixed the io address with 0xe000+idx*8,
but real io address assigned from BIOS is dynamically from
read PCI configure space 0x24, 0x20, 0x1c.

The Fintek F81504/F81508/F81512 maybe malfunction without
this patch and malfunction surely when more then 1 PCI card.
Signed-off-by: NPeter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

tx_empty() should test whether both the transmitter fifo and shifter
for the port is empty, ie. the whole last char was transmitted.
The shift register is empty if AUART_STAT_BUSY is cleared.
The patch fixes the function against the shift register.

According to i.MX23 and i.MX28 Reference Manual:
AUART_STAT_TXFE:
 TX FIFO or transmit holding register is empty.

AUART_STAT_BUSY:
 AUART still transmits bits.
 The BUSY signal goes HIGH as soon as the data is written to the
 transmit FIFO (that is, the FIFO is non-empty) and remains asserted
 HIGH while data is being transmitted.
 BUSY is negated only when the transmit FIFO is empty, and the last
 character has been transmitted from the shift register, including
 the stop bits.
Signed-off-by: NJanusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

mxs_auart_modem_status() did't detect gpio's state change
because s->mctrl_prev was modified before by mctrl_gpio_get().
The patch introduces mctrl_temp variable to fix the bug.
Signed-off-by: NJanusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 732a84a0 ("serial: core: Pass termios to set_ldisc() notifications")
changed the set_ldisc prototype.

At the time of this commit the mxs_auart driver did not implement set_ldisc,
so that's why it has not been converted.

Adapt also mxs_auart_set_ldisc() so that the following build warning can be
fixed:

drivers/tty/serial/mxs-auart.c:962:2: warning: initialization from
incompatible pointer type
  .set_ldisc      = mxs_auart_set_ldisc,
  ^
drivers/tty/serial/mxs-auart.c:962:2: warning: (near initialization
for 'mxs_auart_ops.set_ldisc')
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Tested-by: NJanusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Although the existing code appears to work on most hardware, the
hardware designers tell us that 8-bit access to the registers is not
guaranteed to be reliable.  Also the OCTEON simulation environments
prohibit 8-bit accesses.

For these reasons, we use __raw_readq/__raw_writeq for OCTEON.  This
code is protected with #ifdef CONFIG_64BIT so it still builds under
configurations lacking readq/writeq.

We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses,
OCTEON is byte order invariant.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When CONFIG_SERIAL_IMX_CONSOLE=n and CONFIG_CONSOLE_POLL=y we get the following
build warning:

drivers/tty/serial/imx.c:306:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:315:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]

imx_port_ucrs_save/restore are only used under CONFIG_SERIAL_IMX_CONSOLE, so
their definitions should be also be protected only by CONFIG_SERIAL_IMX_CONSOLE.

This was detected when building 'allmodconfig'.
Reported-by: NOlof's autobuilder <build@lixom.net>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025          if (up.port.line < 0) {

Since of_alias_get_id() and pdev->id can get negative I check for the
error via ret variable.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025          if (up.port.line < 0) {

I (wrongly) assumed that line is an int and compiler didn't complain nor
did sparse. Since of_alias_get_id() and pdev->id can get negative I
check for the error via ret variable.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The mcb_device_id table is supposed to be zero-terminated.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

in CSR A7DA SoC, uart6 located at BT module and it need multiple clock
sources, so for "sirf,marco-bt-uart" compatible uarts, drivers take 3
clock sources and enable them.

this patch also replaces clk_get by devm_clk_get function and fix DT
binding document in which we missed to fix when we added marco platform
in commit 909102db "serial: sirf: add support for Marco chip".
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>