On some systems (Intel tablets with axp288 pmic) the powerbutton is
also connected to a gpio pin of the SoC, advertised through the
"INTCFD9" / "PNP0C40" acpi device. This leads to double reporting
of powerbutton events, which is undesirable, so one driver needs
to not report input events in this case.

Since the soc_button_array driver for the "PNP0C40" acpi device
also handles wake from suspend on these tablets and since the
axp20x-pel driver requires relative expensive i2c accrsses,
it is best for the axp20x-pek driver to not register an input device
in this case.

Note that this commit leaves the axp20x-driver bound to the
device, rather then returning -ENODEV, this is done so that the
sysfs attributes it offers are kept around.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Move all input device related initialization into a new
axp20x_pek_probe_input_device helper function.

This introduces one functional change, the input device is now
registered before the sysfs attr get registered. This is not a problem
as the sysfs attr are to configure some long press settings (forced
poweroff) in the hardware and do not interact with the input_device.

This is a preparation patch for not always registering the input dev.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Before this commit axp20x-pek was mixing 2 style error reporting calls:
dev_err(&pdev->dev, ...);
dev_err(axp20x->dev, ...);

But the second is our parent device, not our own device, so switch to
using &pdev->dev everywhere.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

As the driver is using generic device properties, it should work
properly when CONFIG_OF is turned off. This patch removes the
ifdef CONFIGOF and make sure the driver always have of_match_table.
Signed-off-by: NJingkui Wang <jkwang@google.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Extend the pwm-beeper driver to support customized frequency for SND_BELL
from device properties.
Signed-off-by: NGuan Ben <ben.guan@cn.bosch.com>
Signed-off-by: NMark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Sort all devices in alps_model_data by signature and remove
command_mode_resp which is not used anymore.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Support for devices with ALPS_PROTO_V9 is not implemented yet but we can
detect these alps touchpads and warn users about it.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Like for other protocols create alps_v4_protocol_data and use it in
alps_identify() function.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of manipulating capabilities bits of input device directly, let's
use input_set_capability() API.

Also, stop setting ABS_X/Y bits explicitly as input_set_abs_params() does
this for us.
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

We have switched the driver to use generic device properties API, so there
is no need to check for presence of DT node before trying parse properties.
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

With the switch to devm, there is no need for ad7879_probe() to return the
touchscreen structure, we can use plain error code. This also fixes issue
introduced with devm concersion, where we returned 0 on success (which
worked OK since IS_ERR(0) would not trigger, but was not correct
regardless).

Fixes: 381f688eee3d ("Input: ad7879 - use more devm interfaces")
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The conversion to devm accidentally removed setting up of I2C client data
upon successful probe of the touchscreen. Let's move this setting into the
core, so we do not forger about it again.

Fixes: 381f688eee3d ("Input: ad7879 - use more devm interfaces")
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This moves device tree bindings for ADS7846 together with the other
touchscreen bindings.
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add header file to fix these build errors:

../drivers/input/touchscreen/ad7879.c: In function 'ad7879_parse_dt':
../drivers/input/touchscreen/ad7879.c:505:2: error: implicit declaration of function 'device_property_read_u32' [-Werror=implicit-function-declaration]
  err = device_property_read_u32(dev, "adi,resistance-plate-x", &tmp);
  ^
../drivers/input/touchscreen/ad7879.c:512:2: error: implicit declaration of function 'device_property_read_u8' [-Werror=implicit-function-declaration]
  device_property_read_u8(dev, "adi,first-conversion-delay",
  ^
../drivers/input/touchscreen/ad7879.c:521:2: error: implicit declaration of function 'device_property_read_bool' [-Werror=implicit-function-declaration]
  ts->swap_xy = device_property_read_bool(dev, "touchscreen-swapped-x-y");
  ^
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Bring in TSC2007 improvements.

There is no need to tread the same register twice in a row.

Fixes: ea4348c8 ("Input: tca8418_keypad - hide gcc-4.9 -Wmaybe-un ...")
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Using regmap this is no longer required.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Up until now only platforms using legacy platform data were able to switch
AUX/VBAT/GPIO pin in GPIO mode and use it as regular GPIO line. Let's
allow platforms using generic device properties to do the same.
Reviewed-by: NMichael Hennerich <michael.hennerich@analog.com>
Tested-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

gpiochip_add now has a managed version, and we can remove sysfs attribute
group via devm_add_action_or_reset (at least until we have devm version of
sysfs_create_group). This allows us to get rid of ad7879_remove().
Reviewed-by: NMichael Hennerich <michael.hennerich@analog.com>
Tested-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of rolling our own infrastructure to provide uniform access to I2C
and SPI buses, let's switch to using regmap.
Reviewed-by: NMichael Hennerich <michael.hennerich@analog.com>
Tested-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Previously, tsc2007 would report as ABS_PRESSURE:
0              for no pressure (resistance infinite)
high value     for soft pressure (high resistance)
low value      for firm pressure (lower resistance)

This does not matter for most applications (e.g. GUI, Menu, Scrolling etc.)
where the ABS_PRESSURE is ignored and only BTN_TOUCH is processed to detect
screen taps.

Only some special graphics applications read the pressure channel and they
will be mixed up by this non-monotonic relation.

So we fix it to become:
0              for no pressure (resistance infinite)
low value      for soft pressure (high resistance)
high value     for firm pressure (lower resistance)

While this patch changes the values reported to userspace, ABS_PRESSURE is
used rarely by userspace. Most software only relies on BTN_TOUCH (boolean),
which is not affected by this patch. Some graphics software makes use of
the interface and does not work correctly with the currently used inverted
behaviour.
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Reviewed-By: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Rename tsc2007_calculate_pressure to tsc2007_calculate_resistance because
that is what it does.
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Do not manipulate evbits/keybits directly, use helper for that.
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.

Before this patch:

$ modinfo drivers/input/touchscreen/zet6223.ko | grep alias
alias:          i2c:zet6223

After this patch:

$ modinfo drivers/input/touchscreen/zet6223.ko | grep alias
alias:          of:N*T*Czeitec,zet6223C*
alias:          of:N*T*Czeitec,zet6223
alias:          i2c:zet6223
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The tsc2007 chip not only has a resistive touch screen controller but
also an external AUX adc imput which can be used for an ambient
light sensor, battery voltage monitoring or any general purpose.

Additionally it can measure the chip temperature.

This extension provides an iio interface for these adc channels.

Since it is not wasting much resources and is very straightforward,
we simply provide all other adc channels as optional iio interfaces
as weel. This can be used for debugging or special applications.

This patch also splits the tsc2007 driver in several source files:
tsc2007.h -- constants, structs and stubs
tsc2007_core.c -- functional parts of the original driver
tsc2007_iio.c -- the optional iio stuff

Makefile magic allows to conditionally link the iio stuff
if CONFIG_IIO=y or =m in a way that it works with
CONFIG_TOUCHSCREEN_TSC2007=m.
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

1. check if chip is really present and don't succeed if it isn't.
2. if it succeeds, power down the chip until accessed
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Merge in cros-ec changes applied through MFD branch to resolve
conflicts.

Add switch to report tablet mode.
Signed-off-by: NGwendal Grignou <gwendal@chromium.org>
Signed-off-by: NEnric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Instead of supporting legacy platform data (of which we have no mainline
users) and OF-based properties, let's switch to generic device properties.
This will still allow legacy boards to use the driver (by defining property
sets and attaching them to the drivers) and will simplify probe and make
driver usable on ACPI-based systems as well.
Reviewed-By: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

In case of an optional regulator missing, regulator core will return
ERR_PTR(-ENOENT) and not NULL, so the check for missing regulator is
incorrect. Also, the regulator is not optional, it may simply be missing
from platform description, so let's use devm_regulator_get() and rely on
regulator core to give us dummy supply when real one is not available.

Fixes: d257f298 ("Input: tsc2005 - convert to gpiod")
Acked-By: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

To be prepared for SPI module loading using full compatible strings from
device tree, let's add OF module device table data.
Reviewed-By: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This is a basic driver for the Zeitec ZET6223 I2C touchscreen
controllers. The driver does not support firmware loading, which is not
required for all tablets which contain this chip.
Signed-off-by: NJelle van der Waa <jelle@vdwaa.nl>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Postpone axis initialization to the first open instead of doing it
in joydev_connect. This is to make sure the generated startup events
are representative of the current joystick state rather than what
it was when joydev_connect() was called, potentially much earlier.
Once the first user is connected to joydev node we'll be updating
joydev->abs[] values and subsequent clients will be getting correct
initial states as well.

This solves issues with joystick driven menus that start scrolling
up each time they are started, until the user moves the joystick to
generate events. In emulator menu setups where the menu program is
restarted every time the game exits, the repeated need to move the
joystick to stop the unintended scrolling gets old rather quickly...
Signed-off-by: NRaphael Assenat <raph@raphnet.net>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

On the latest series of ThinkPads, the button events for the TrackPoint
are reported through the touchpad itself as opposed to the TrackPoint
device. In order to report these buttons properly, we need to forward
them to the TrackPoint device and notify psmouse to send the button
presses/releases.
Signed-off-by: NLyude Paul <thatslyude@gmail.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch does several cleanup changes to F30 code

- switch to using BIT() macro
- use DIV_ROUND_UP() where appropriate
- factor out code setting up and reporting buttons
- use single loop when reporting buttons: arithmetic is cheap compared to
  conditionals and associated branch misprediction.
Tested-By: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of using custom method of "passing" extended buttons from the
touchpad to trackstick, let's switch to the newly introduced SERIO_OOB_DATA
channel.
Tested-By: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The tracksticks on the Lenovo thinkpads have their buttons connected
through the touchpad device. We already fixed that in synaptics.c, but
when we switch the device into RMI4 mode to have proper support, the
pass-through functionality can't deal with them easily.

We add a new PS/2 flag and protocol designed for psmouse.  The RMI4 F03
pass-through can then emit a special set of commands to notify psmouse the
state of the buttons.

This patch implements the protocol in psmouse, while an other will
do the same for rmi4-f03.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

On some newer boards using mkbp we're hooking up non-matrix buttons and
switches to the EC but NOT to the main application processor.

Let's add kernel support to handle this.  Rather than creating a whole
new input driver, we'll continue to use cros_ec_keyb and just report the
new keys.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>