- 05 12月, 2012 3 次提交
-
-
由 Nicolas Dichtel 提交于
A mfc entry can be static or not (added via the mroute_sk socket). The patch reports MFC_STATIC flag into rtm_protocol by setting rtm_protocol to RTPROT_STATIC or RTPROT_MROUTED. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
These statistics can be checked only via /proc/net/ip_mr_cache or SIOCGETSGCNT[_IN6] and thus only for the table RT_TABLE_DEFAULT. Advertising them via rtnetlink allows to get statistics for all cache entries, whatever the table is. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
This patch advertise the MC_FORWARDING status for IPv4 and IPv6. This field is readonly, only multicast engine in the kernel updates it. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 12月, 2012 1 次提交
-
-
由 Michael S. Tsirkin 提交于
Historically tun supported two modes of operation: - in default mode, a small number of packets would get queued at the device, the rest would be queued in qdisc - in one queue mode, all packets would get queued at the device This might have made sense up to a point where we made the queue depth for both modes the same and set it to a huge value (500) so unless the consumer is stuck the chance of losing packets is small. Thus in practice both modes behave the same, but the default mode has some problems: - if packets are never consumed, fragments are never orphaned which cases a DOS for sender using zero copy transmit - overrun errors are hard to diagnose: fifo error is incremented only once so you can not distinguish between userspace that is stuck and a transient failure, tcpdump on the device does not show any traffic Userspace solves this simply by enabling IFF_ONE_QUEUE but there seems to be little point in not doing the right thing for everyone, by default. Signed-off-by: NMichael S. Tsirkin <mst@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 12月, 2012 1 次提交
-
-
由 Pablo Neira Ayuso 提交于
This patch adds a new operation to dump the content of the dying and unconfirmed lists. Under some situations, the global conntrack counter can be inconsistent with the number of entries that we can dump from the conntrack table. The way to resolve this is to allow dumping the content of the unconfirmed and dying lists, so far it was not possible to look at its content. This provides some extra instrumentation to resolve problematic situations in which anyone suspects memory leaks. Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
- 26 11月, 2012 4 次提交
-
-
由 Johannes Berg 提交于
Add support for reporting and calculating VHT MCSes. Note that I'm not completely sure that the bitrate calculations are correct, nor that they can't be simplified. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Change nl80211 to support specifying a VHT (or HT) using the control channel frequency (as before) and new attributes for the channel width and first and second center frequency. The old channel type is of course still supported for HT. Also change the cfg80211 channel definition struct to support these by adding the relevant fields to it (and removing the _type field.) This also adds new helper functions: - cfg80211_chandef_create to create a channel def struct given the control channel and channel type, - cfg80211_chandef_identical to check if two channel definitions are identical - cfg80211_chandef_compatible to check if the given channel definitions are compatible, and return the wider of the two This isn't entirely complete, but that doesn't matter until we have a driver using it. In particular, it's missing - regulatory checks on the usable bandwidth (if that even makes sense) - regulatory TX power (database can't deal with it) - a proper channel compatibility calculation for the new channel types Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
As mwifiex (and mac80211 in the software case) are the only drivers actually implementing remain-on-channel with channel type, userspace can't be relying on it. This is the case, as it's used only for P2P operations right now. Rather than adding a flag to tell userspace whether or not it can actually rely on it, simplify all the code by removing the ability to use different channel types. Leave only the validation of the attribute, so that if we extend it again later (with the needed capability flag), it can't break userspace sending invalid data. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 21 11月, 2012 2 次提交
-
-
由 Nicolas Dichtel 提交于
This patch add the support of 6RD tunnels management via netlink. Note that netdev_state_change() is now called when 6RD parameters are updated. 6RD parameters are updated only if there is at least one 6RD attribute. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Stevens 提交于
This patch provides extensions to VXLAN for supporting Distributed Overlay Virtual Ethernet (DOVE) networks. The patch includes: + a dove flag per VXLAN device to enable DOVE extensions + ARP reduction, whereby a bridge-connected VXLAN tunnel endpoint answers ARP requests from the local bridge on behalf of remote DOVE clients + route short-circuiting (aka L3 switching). Known destination IP addresses use the corresponding destination MAC address for switching rather than going to a (possibly remote) router first. + netlink notification messages for forwarding table and L3 switching misses Changes since v2 - combined bools into "u32 flags" - replaced loop with !is_zero_ether_addr() Signed-off-by: NDavid L Stevens <dlstevens@us.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 11月, 2012 1 次提交
-
-
由 Jouni Malinen 提交于
The NL80211_CMD_TDLS_OPER command was previously used only for userspace request for the kernel code to perform TDLS operations. However, there are also cases where the driver may need to request operations from userspace, e.g., when using security on the AP path. Add a new cfg80211 function for generating a TDLS operation event for drivers to request a new link to be set up (NL80211_TDLS_SETUP) or an existing link to be torn down (NL80211_TDLS_TEARDOWN). Drivers can optionally use these events, e.g., based on noticing data traffic being sent to a peer station that is seen with good signal strength. Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 17 11月, 2012 1 次提交
-
-
由 David Rientjes 提交于
This is mostly a revert of 01dc52eb ("oom: remove deprecated oom_adj") from Davidlohr Bueso. It reintroduces /proc/pid/oom_adj for backwards compatibility with earlier kernels. It simply scales the value linearly when /proc/pid/oom_score_adj is written. The major difference is that its scheduled removal is no longer included in Documentation/feature-removal-schedule.txt. We do warn users with a single printk, though, to suggest the more powerful and supported /proc/pid/oom_score_adj interface. Reported-by: NArtem S. Tashkinov <t.artem@lycos.com> Signed-off-by: NDavid Rientjes <rientjes@google.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 16 11月, 2012 1 次提交
-
-
由 Nicolas Dichtel 提交于
The kernel uses some default metric when routes are managed. For example, a static route added with a metric set to 0 is inserted in the kernel with metric 1024 (IP6_RT_PRIO_USER). It is useful for routing daemons to know these values, to be able to set routes without interfering with what the kernel does. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 11月, 2012 5 次提交
-
-
由 Nicolas Dichtel 提交于
This parameter was missing in the dump. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
IPv6 tunnels can have three mode: 4in6, 6in6 and xin6. This information was missing in the netlink message. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
This is Linux bridge implementation of root port guard. If BPDU is received from a leaf (edge) port, it should not be elected as root port. Why would you want to do this? If using STP on a bridge and the downstream bridges are not fully trusted; this prevents a hostile guest for rerouting traffic. Why not just use netfilter? Netfilter does not track of follow spanning tree decisions. It would be difficult and error prone to try and mirror STP resolution in netfilter module. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
This is Linux bridge implementation of STP protection (Cisco BPDU guard/Juniper BPDU block). BPDU block disables the bridge port if a STP BPDU packet is received. Why would you want to do this? If running Spanning Tree on bridge, hostile devices on the network may send BPDU and cause network failure. Enabling bpdu block will detect and stop this. How to recover the port? The port will be restarted if link is brought down, or removed and reattached. For example: # ip li set dev eth0 down; ip li set dev eth0 up Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Expose bridge port parameter over netlink. By switching to a nested message, this can be used for other bridge parameters. This changes IFLA_PROTINFO attribute from one byte to a full nested set of attributes. This is safe for application interface because the old message used IFLA_PROTINFO and new one uses IFLA_PROTINFO | NLA_F_NESTED. The code adapts to old format requests, and therefore stays compatible with user mode RSTP daemon. Since the type field for nested and unnested attributes are different, and the old code in libnetlink doesn't do the mask, it is also safe to use with old versions of bridge monitor command. Note: although mode is only a boolean, treating it as a full byte since in the future someone will probably want to add more values (like macvlan has). Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 11月, 2012 1 次提交
-
-
由 Hannes Frederic Sowa 提交于
This patch introduces a new knob ndisc_notify. If enabled, the kernel will transmit an unsolicited neighbour advertisement on link-layer address change to update the neighbour tables of the corresponding hosts more quickly. This is the equivalent to arp_notify in ipv4 world. Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 11月, 2012 1 次提交
-
-
由 Amitkumar Karwar 提交于
wpa_supplicant will do OBSS scan for drivers that implement auth/assoc API. Drivers that implement nl80211 connect API (rather than auth/assoc) may need wpa_supplicant to do this as well. Add a new feature flag to inform it (wpa_s) that a driver needs wpa_supplicant to do OBSS scans. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 10 11月, 2012 4 次提交
-
-
由 Nicolas Dichtel 提交于
It is usefull for daemons that monitor link event to have the full parameters of these interfaces when a rtnl message is sent. It allows also to dump them via rtnetlink. It is based on what is done for GRE tunnels. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
It is usefull for daemons that monitor link event to have the full parameters of these interfaces when a rtnl message is sent. It allows also to dump them via rtnetlink. It is based on what is done for GRE tunnels. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Howells 提交于
Fix the wanxl firmware to include missing constants such as PARITY_NONE. It should be #including the linux/hdlc/ioctl.h header. To make this work, we also have to guard parts of ioctl.h with !__ASSEMBLY__. Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Howells 提交于
Signed-off-by: NDavid Howells <dhowells@redhat.com> Acked-by: NArnd Bergmann <arnd@arndb.de> Acked-by: NThomas Gleixner <tglx@linutronix.de> Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com> Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: NDave Jones <davej@redhat.com> Acked-by: NKrzysztof Halasa <khc@pm.waw.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 11月, 2012 1 次提交
-
-
由 Andrew Morton 提交于
Revert commit 03a7beb5 ("epoll: support for disabling items, and a self-test app") pending resolution of the issues identified by Michael Kerrisk, copied below. We'll revisit this for 3.8. : I've taken a look at this patch as it currently stands in 3.7-rc1, and : done a bit of testing. (By the way, the test program : tools/testing/selftests/epoll/test_epoll.c does not compile...) : : There are one or two places where the behavior seems a little strange, : so I have a question or two at the end of this mail. But other than : that, I want to check my understanding so that the interface can be : correctly documented. : : Just to go though my understanding, the problem is the following : scenario in a multithreaded application: : : 1. Multiple threads are performing epoll_wait() operations, : and maintaining a user-space cache that contains information : corresponding to each file descriptor being monitored by : epoll_wait(). : : 2. At some point, a thread wants to delete (EPOLL_CTL_DEL) : a file descriptor from the epoll interest list, and : delete the corresponding record from the user-space cache. : : 3. The problem with (2) is that some other thread may have : previously done an epoll_wait() that retrieved information : about the fd in question, and may be in the middle of using : information in the cache that relates to that fd. Thus, : there is a potential race. : : 4. The race can't solved purely in user space, because doing : so would require applying a mutex across the epoll_wait() : call, which would of course blow thread concurrency. : : Right? : : Your solution is the EPOLL_CTL_DISABLE operation. I want to : confirm my understanding about how to use this flag, since : the description that has accompanied the patches so far : has been a bit sparse : : 0. In the scenario you're concerned about, deleting a file : descriptor means (safely) doing the following: : (a) Deleting the file descriptor from the epoll interest list : using EPOLL_CTL_DEL : (b) Deleting the corresponding record in the user-space cache : : 1. It's only meaningful to use this EPOLL_CTL_DISABLE in : conjunction with EPOLLONESHOT. : : 2. Using EPOLL_CTL_DISABLE without using EPOLLONESHOT in : conjunction is a logical error. : : 3. The correct way to code multithreaded applications using : EPOLL_CTL_DISABLE and EPOLLONESHOT is as follows: : : a. All EPOLL_CTL_ADD and EPOLL_CTL_MOD operations should : should EPOLLONESHOT. : : b. When a thread wants to delete a file descriptor, it : should do the following: : : [1] Call epoll_ctl(EPOLL_CTL_DISABLE) : [2] If the return status from epoll_ctl(EPOLL_CTL_DISABLE) : was zero, then the file descriptor can be safely : deleted by the thread that made this call. : [3] If the epoll_ctl(EPOLL_CTL_DISABLE) fails with EBUSY, : then the descriptor is in use. In this case, the calling : thread should set a flag in the user-space cache to : indicate that the thread that is using the descriptor : should perform the deletion operation. : : Is all of the above correct? : : The implementation depends on checking on whether : (events & ~EP_PRIVATE_BITS) == 0 : This replies on the fact that EPOLL_CTL_AD and EPOLL_CTL_MOD always : set EPOLLHUP and EPOLLERR in the 'events' mask, and EPOLLONESHOT : causes those flags (as well as all others in ~EP_PRIVATE_BITS) to be : cleared. : : A corollary to the previous paragraph is that using EPOLL_CTL_DISABLE : is only useful in conjunction with EPOLLONESHOT. However, as things : stand, one can use EPOLL_CTL_DISABLE on a file descriptor that does : not have EPOLLONESHOT set in 'events' This results in the following : (slightly surprising) behavior: : : (a) The first call to epoll_ctl(EPOLL_CTL_DISABLE) returns 0 : (the indicator that the file descriptor can be safely deleted). : (b) The next call to epoll_ctl(EPOLL_CTL_DISABLE) fails with EBUSY. : : This doesn't seem particularly useful, and in fact is probably an : indication that the user made a logic error: they should only be using : epoll_ctl(EPOLL_CTL_DISABLE) on a file descriptor for which : EPOLLONESHOT was set in 'events'. If that is correct, then would it : not make sense to return an error to user space for this case? Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: "Paton J. Lewis" <palewis@adobe.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 08 11月, 2012 1 次提交
-
-
由 Paul Chavent 提交于
The tx data offset of packet mmap tx ring used to be : (TPACKET2_HDRLEN - sizeof(struct sockaddr_ll)) The problem is that, with SOCK_RAW socket, the payload (14 bytes after the beginning of the user data) is misaligned. This patch allows to let the user gives an offset for it's tx data if he desires. Set sock option PACKET_TX_HAS_OFF to 1, then specify in each frame of your tx ring tp_net for SOCK_DGRAM, or tp_mac for SOCK_RAW. Signed-off-by: NPaul Chavent <paul.chavent@onera.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 11月, 2012 1 次提交
-
-
由 Antonio Quartulli 提交于
This command triggers a new callback: set_mcast_rate(). It enables the user to change the rate used to send multicast frames for vif configured as IBSS or MESH_POINT Signed-off-by: NAntonio Quartulli <ordex@autistici.org> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 04 11月, 2012 1 次提交
-
-
由 Antonio Quartulli 提交于
Add Ethertype 0x4305 (not an officially registered id). This Ethertype is used by every frame generated by B.A.T.M.A.N.-Advanced. Its definition is currently batman-adv local only and since it is not officially registered it is better to make its definition kernel-wide so that we avoid collisions given by future unofficial uses of the same Ethertype. Signed-off-by: NAntonio Quartulli <ordex@autistici.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 11月, 2012 2 次提交
-
-
由 Florian Westphal 提交于
userspace can query the original ipv4 destination address of a REDIRECTed connection via getsockopt(m_sock, SOL_IP, SO_ORIGINAL_DST, &m_server_addr, &addrsize) but for ipv6 no such option existed. This adds getsockopt(..., IPPROTO_IPV6, IP6T_SO_ORIGINAL_DST, ...). Without this, userspace needs to parse /proc or use ctnetlink, which appears to be overkill. This uses option number 80 for IP6T_SO_ORIGINAL_DST, which is spare, to use the same number we use in the IPv4 socket option SO_ORIGINAL_DST. Signed-off-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Nicolas Dichtel 提交于
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 11月, 2012 6 次提交
-
-
由 Richard Cochran 提交于
This patch adds an ioctl for PTP Hardware Clock (PHC) devices that allows user space to measure the time offset between the PHC and the system clock. Rather than hard coding any kind of estimation algorithm into the kernel, this patch takes the more flexible approach of just delivering an array of raw clock readings. In that way, the user space clock servo may be adapted to new and different hardware clocks. Signed-off-by: NRichard Cochran <richardcochran@gmail.com> Acked-by: NJacob Keller <jacob.e.keller@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Pavel Emelyanov 提交于
The SO_ATTACH_FILTER option is set only. I propose to add the get ability by using SO_ATTACH_FILTER in getsockopt. To be less irritating to eyes the SO_GET_FILTER alias to it is declared. This ability is required by checkpoint-restore project to be able to save full state of a socket. There are two issues with getting filter back. First, kernel modifies the sock_filter->code on filter load, thus in order to return the filter element back to user we have to decode it into user-visible constants. Fortunately the modification in question is interconvertible. Second, the BPF_S_ALU_DIV_K code modifies the command argument k to speed up the run-time division by doing kernel_k = reciprocal(user_k). Bad news is that different user_k may result in same kernel_k, so we can't get the original user_k back. Good news is that we don't have to do it. What we need to is calculate a user2_k so, that reciprocal(user2_k) == reciprocal(user_k) == kernel_k i.e. if it's re-loaded back the compiled again value will be exactly the same as it was. That said, the user2_k can be calculated like this user2_k = reciprocal(kernel_k) with an exception, that if kernel_k == 0, then user2_k == 1. The optlen argument is treated like this -- when zero, kernel returns the amount of sock_fprog elements in filter, otherwise it should be large enough for the sock_fprog array. changes since v1: * Declared SO_GET_FILTER in all arch headers * Added decode of vlan-tag codes Signed-off-by: NPavel Emelyanov <xemul@parallels.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jason Wang 提交于
Sometimes usespace may need to active/deactive a queue, this could be done by detaching and attaching a file from tuntap device. This patch introduces a new ioctls - TUNSETQUEUE which could be used to do this. Flag IFF_ATTACH_QUEUE were introduced to do attaching while IFF_DETACH_QUEUE were introduced to do the detaching. Signed-off-by: NJason Wang <jasowang@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jason Wang 提交于
Add flags to be used by creating multiqueue tuntap device. Signed-off-by: NJason Wang <jasowang@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
BPF filters lack ability to access skb->vlan_tci This patch adds two new ancillary accessors : SKF_AD_VLAN_TAG (44) mapped to vlan_tx_tag_get(skb) SKF_AD_VLAN_TAG_PRESENT (48) mapped to vlan_tx_tag_present(skb) This allows libpcap/tcpdump to use a kernel filter instead of having to fallback to accept all packets, then filter them in user space. Signed-off-by: NEric Dumazet <edumazet@google.com> Suggested-by: NAni Sinha <ani@aristanetworks.com> Suggested-by: NDaniel Borkmann <danborkmann@iogearbox.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John Fastabend 提交于
Hardware switches may support enabling and disabling the loopback switch which puts the device in a VEPA mode defined in the IEEE 802.1Qbg specification. In this mode frames are not switched in the hardware but sent directly to the switch. SR-IOV capable NICs will likely support this mode I am aware of at least two such devices. Also I am told (but don't have any of this hardware available) that there are devices that only support VEPA modes. In these cases it is important at a minimum to be able to query these attributes. This patch adds an additional IFLA_BRIDGE_MODE attribute that can be set and dumped via the PF_BRIDGE:{SET|GET}LINK operations. Also anticipating bridge attributes that may be common for both embedded bridges and software bridges this adds a flags attribute IFLA_BRIDGE_FLAGS currently used to determine if the command or event is being generated to/from an embedded bridge or software bridge. Finally, the event generation is pulled out of the bridge module and into rtnetlink proper. For example using the macvlan driver in VEPA mode on top of an embedded switch requires putting the embedded switch into a VEPA mode to get the expected results. -------- -------- | VEPA | | VEPA | <-- macvlan vepa edge relays -------- -------- | | | | ------------------ | VEPA | <-- embedded switch in NIC ------------------ | | ------------------- | external switch | <-- shiny new physical ------------------- switch with VEPA support A packet sent from the macvlan VEPA at the top could be loopbacked on the embedded switch and never seen by the external switch. So in order for this to work the embedded switch needs to be set in the VEPA state via the above described commands. By making these attributes nested in IFLA_AF_SPEC we allow future extensions to be made as needed. CC: Lennert Buytenhek <buytenh@wantstofly.org> CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 10月, 2012 1 次提交
-
-
由 Johannes Berg 提交于
The TX power setting is currently per wiphy (hardware device) but with multi-channel capabilities that doesn't make much sense any more. Allow drivers (and mac80211) to advertise support for per-interface TX power configuration. When the TX power is configured for the wiphy, the wdev will be NULL and the driver can still handle that, but when a wdev is given the TX power can be set only for that wdev now. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 29 10月, 2012 2 次提交
-
-
由 Thierry Escande 提交于
NFC_CMD_LLC_GET_PARAMS: request LTO, RW, and MIUX parameters for a device NFC_CMD_LLC_SET_PARAMS: set one or more of LTO, RW, and MIUX parameters for a device. LTO must be set before the link is up otherwise -EINPROGRESS is returned. RW and MIUX can be set at anytime and will be passed in subsequent CONNECT and CC messages. If one of the passed parameters is wrong none is set and -EINVAL is returned. Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com> Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
-
由 Nicolas Dichtel 提交于
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-