This removes the following functions:
si_pmu_chipcontrol() => bcma_chipco_chipctl_maskset()
si_pmu_regcontrol() => bcma_chipco_regctl_maskset()
si_pmu_pllcontrol() => bcma_chipco_pll_maskset()
si_pmu_pllupd() => bcma_cc_set32()
si_pmu_alp_clock() => bcma_chipco_get_alp_clock()

This also removed the sih member from struct shared_phy.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The messages are currently hard coding "1ms", which does not match
the actual timeout being used.
Signed-off-by: NRobert Shade <robert.shade@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Marco Fonseca reported a issue with his carl9170 device:
"I'm seeing a problem with the carl driver. If I change channels
repeatedly on the 2.4ghz band, monitoring (e.g. tcpdump) will
eventually halt.  I've seen this on various versions of the carl
driver/firmware (both from 1.9.4 to 1.9.7)"
<http://marc.info/?l=linux-wireless&m=136381302428113>

The culprit was identified as "fast channel change feature" which
according to Adrian Chadd is: "... notoriously unreliable and
really only fully debugged on some very later chips."
<http://marc.info/?l=linux-wireless&m=136416984531380>

Therefore, this patch removes the fast channel change feature.
The phy will now always have to go through a cold reset when
changing channels, but it should no longer become deaf.

Cc: Marco Fonseca <marco@tampabay.rr.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix settings not being applied when the device is idle and the firmware
gets reloaded (because of changing from STA to AP mode). This caused
the device using the wrong channel (and likely band), e.g. a 5 GHz only
card still defaulted to channel 6 in the 2.4 GHz band when left
unconfigured.

This issue was always present, but only made visible with "mwl8k: Do not
call mwl8k_cmd_set_rf_channel unconditionally" (0f4316b9), since before
that the channel was (re-)configured at the next _config call even when
it did not change from the mac80211 perspective.
Signed-off-by: NJonas Gorski <jogo@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds adhoc mode support to brcmsmac.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This activates the AP mode support.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is possible to configure the ucode to automatically send the probe
responses to the clients after they send a probe request. At least for
WPS the userspace needs to answer the probe requests and we do not know
a way to say to the ucode to just handle the normal probe requests, so
for now no probe requests should be handled by the ucode.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ucode is able to answer probe response by itself. This writes such
a template into the specific memory. Currently the probe requests are
also send to mac80211 so there are more answers send to a requesting
client. We have to make the ucode stop sending probe requests to the
driver.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To send the correct probe response the hardware needs to know the SSID
when it changed.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes it possible that a beacon template provided by mac80211 is
written to the hardware for constant beaconing.

This is based on an old version of brcmsmac, on b43 and the spec b43 is
based on.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make brcms_c_set_beacon_period() write the beacon period to the
hardware if a new one is set.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This was a write only member
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

use brcms_pub->cur_etheraddr instead
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This was a read only member, replace it with pub->up.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This was a read only member.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replaced the usage with pub->associated.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This was a read only member. The checks using BSS are replaced by
better fitting checks of the new type member.

The change in brcms_c_tbtt() was based on code from b43, in
brcms_c_ps_allowed() the same happens with BSS being true or false,
beaconing and probe responses are just needed in ap mode.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes it possible to easily check in which mode the device is
currently running. This also adds a function to start station mode.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

setting the tsf is needed to start a timer to make beaconing in AP mode
work.

This is based on older versions of brcmsmac and b43.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of defining the magic values in the code use constants.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

FW can be woken up even by accessing device registers; we need
not explicitily enable interrupts for doing this. Future PCIe
devices will not be woken up by writing to host registers.
This patch enables driver to wake up device by reading FW status
register.

Also devices with sleep cookie enabled need some more time before
proceeding with processing. Handle this by adding a delay loop.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have received interrupt from device means FW is not sleeping.
In this case make sure wakeup handler for PCIe is not invoked by
setting adapter->pm_wakeup_fw_try to false.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling PCIe host interrupt may accidently wake up the card
when it's in sleep.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 6236dc2e ("brcmsmac: remove some redundant chip common workarounds")
removed the last uses.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The spectral data provided via relay-fs introduces a buffering
latency given by the subbuf_size. To meet the requirements for
delay-sensitive applications (like real-time spectral plotter),
reduce subbuf_size and increase n_subbufs.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When calculating "offset" for final RSSI calibration we're using numbers
bigger than s8 can hold. We have for example:
offset[j] = 232 - poll_results[j];
formula. If poll_results[j] is small enough (it usually is) we treat
number's bit as a sign bit. For example 232 - 1 becomes:
0xE8 - 0x1 = 0xE7, which is not 231 but -25.

This code was introduced in e0c9a021
and caused stability regression on some cards, for ex. BCM4322.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

il4965_rs_initialize_lq checks to see if sta is null, however, before that
check il4965_rs_use_green dereferences sta when intializing use_green.
Avoid a potential null pointer dereference error by only calling
il4965_rs_use_green after we are sure sta is not null.

Smatch analysis:

drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn:
  variable dereferenced before check 'sta' (see line 2155)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The following issue was reported.

WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]()
Hardware name: iMac12,1
queueing ieee80211 work while going to suspend
Pid: 0, comm: swapper/0 Tainted: PF          O 3.8.2-206.fc18.x86_64 #1
Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992]  <IRQ>
[<ffffffff8105e61f>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa0581420>] ? ath_start_rx_poll+0x70/0x70 [ath9k]
<ffffffff8105e716>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa045b542>] ieee80211_can_queue_work.isra.7+0x32/0x40

Fix this by avoiding to queue the work if our device has
already been marked as suspended or stopped.
Reported-by: NParag Warudkar <parag.lkml@gmail.com>
Tested-by: NParag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.

This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.

Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.
Tested-by: NChris Vine <chris@cvine.freeserve.co.uk>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We're using "mind" variable to find the VCM that got the best polling
results. For each VCM we calculte "currd" which is compared to the
"mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a
value smaller than 40 makes no sense, so increase the initial value.

This fixes a regression introduced in 3.4 by commit:
e0c9a021
(my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s)
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit b6fc28a1.

This commit is reported to cause a regression in the support for some
revisions of 4313 ePA devices.

http://marc.info/?l=linux-wireless&m=136360340200943&w=2

Conflicts:
	drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
Reported-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The BCM5354 SoC has a build in ieee80211 core rev 13 with a LP-PHY on
it. This devices has a sprom version 3 stored in the nvram. This patch
removes the warning and uses the opo values from the sprom as mentioned
in the specs.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this patch the same registers are written, but this access is now
protected by a lock.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, default VHT configuration from the firmware is used
for the VHT operations. Adding vhtcfg command to configure the
firmware based on input received from cfg.

Enable VHT for AP mode only when cfg80211_ap_settings has a
VHT IE i.e., when ieee80211ac is set to 1 in the hostapd.conf.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add proper alignment at first packet copy, to avoid extra copies made later
in networking stack.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move processing of received packets to tasklet from hard-irq context.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX path has extra copying of packets, that can be avoided.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use dedicated DMA coherent buffers for RX urbs, to avoid allocation of large
skbuffs in hard-irq context and improve performance.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is a bug fix for an issue wherein power save was not
working for PCIe. This happens because for processing power save
sleep confirm command we pull skb so that skb->data points ahead
of interface header. We use same skb to get other cmda responses
as well. So if we don't push skb after processing cmd response,
it results into reduction in skb->len and finally skb->len reaches
zero. This causes failure in processing sleep command response.
Fix this by pushing skb by INTF_HEADER_LEN at the end of command
response processing.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Spin locks and completions are expensive in hard IRQ context and cause
problems with RT kernels.  In RT kernels, both spin locks and
completions can schedule(), so we can't use them in hard irq context.

Move handling code into the irq thread function to avoid that.
Reported-by: NGregoire Gentil <gregoire@alwaysinnovating.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>