Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 11 3月, 2008 1 次提交
  3. 26 1月, 2008 5 次提交
  5. 24 1月, 2008 1 次提交
  7. 12 1月, 2008 5 次提交
  9. 25 11月, 2007 1 次提交
  11. 23 10月, 2007 1 次提交
  13. 16 10月, 2007 1 次提交
  15. 10 10月, 2007 1 次提交
  17. 27 7月, 2007 1 次提交
  19. 20 7月, 2007 1 次提交
    • P
      mm: Remove slab destructors from kmem_cache_create(). · 20c2df83
      由 Paul Mundt 提交于 
      Slab destructors were no longer supported after Christoph's
c59def9f change. They've been
BUGs for both slab and slub, and slob never supported them
either.

This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      20c2df83
  21. 18 7月, 2007 1 次提交
    • R
      IB/iser: Make a couple of functions static · 41179e2d
      由 Roland Dreier 提交于 
      Make iser_conn_release() and iser_start_rdma_unaligned_sg() static,
since they are only used in the .c file where they are defined.  In
addition to being a cleanup, this even shrinks the generated code by
allowing the single call of iser_start_rdma_unaligned_sg() to be
inlined into its callsite.  On x86_64:

add/remove: 0/1 grow/shrink: 1/0 up/down: 466/-533 (-67)
function                                     old     new   delta
iser_reg_rdma_mem                           1518    1984    +466
iser_start_rdma_unaligned_sg                 533       -    -533
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      41179e2d
  23. 10 7月, 2007 1 次提交
  25. 19 6月, 2007 1 次提交
  27. 03 6月, 2007 3 次提交
    • M
      [SCSI] iscsi class, iscsi_tcp, iser, qla4xxx: add netdevname sysfs attr · d8196ed2
      由 Mike Christie 提交于 
      iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      d8196ed2
    • M
      [SCSI] libiscsi: make can_queue configurable · 1548271e
      由 Mike Christie 提交于 
      This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      1548271e
    • M
      [SCSI] libiscsi: fix iscsi cmdsn allocation · 77a23c21
      由 Mike Christie 提交于 
      The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.

This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      77a23c21
  29. 02 6月, 2007 4 次提交
  31. 09 5月, 2007 1 次提交
  33. 07 5月, 2007 1 次提交
    • M
      IB: Add CQ comp_vector support · f4fd0b22
      由 Michael S. Tsirkin 提交于 
      Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API.  Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value.  Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.

We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity.  This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      f4fd0b22
  35. 06 4月, 2007 1 次提交
    • E
      IB/iser: Don't defer connection failure notification to workqueue · 1d426d64
      由 Erez Zilber 提交于 
      When a connection is terminated asynchronously from the iSCSI layer's
perspective, iSER needs to notify the iSCSI layer that the connection
has failed.  This is done using a workqueue (switched to from the iSER
tasklet context).  Meanwhile, the connection object (that holds the
work struct) is released.  If the workqueue function wasn't called
yet, it will be called later with a NULL pointer, which will crash the
kernel.

The context switch (tasklet to workqueue) is not required, and
everything can be done from the iSER tasklet. This eliminates the NULL
work struct bug (and simplifies the code).
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      1d426d64
  37. 27 3月, 2007 1 次提交
  39. 12 3月, 2007 1 次提交
  41. 10 2月, 2007 1 次提交
  43. 08 1月, 2007 1 次提交
  45. 13 12月, 2006 2 次提交
  47. 09 12月, 2006 1 次提交
    • D
      [PATCH] LOG2: Implement a general integer log2 facility in the kernel · f0d1b0b3
      由 David Howells 提交于 
      This facility provides three entry points:

	ilog2()		Log base 2 of unsigned long
	ilog2_u32()	Log base 2 of u32
	ilog2_u64()	Log base 2 of u64

These facilities can either be used inside functions on dynamic data:

	int do_something(long q)
	{
		...;
		y = ilog2(x)
		...;
	}

Or can be used to statically initialise global variables with constant values:

	unsigned n = ilog2(27);

When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant.  They treat negative numbers as
unsigned.

When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.

[akpm@osdl.org: MMC fix]
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      f0d1b0b3
  49. 04 12月, 2006 1 次提交
  51. 30 11月, 2006 1 次提交