We don't use it during development and we can't extend it either, so
remove it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver "dwc-xlgmac" is dual-licensed.
Declare the dual license with MODULE_LICENSE().
Signed-off-by: NJie Deng <jiedeng@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver "dwc-xlgmac" is dual-licensed. This patch adds
declaration of dual license in file headers.
Signed-off-by: NJie Deng <jiedeng@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Align the driver feature distribution with the flow utilized
by the management firmware - first reserve L2 queues for
VFs and use all the remaining for the PF.

The current distribution might lead to PFs with an enormous
amount of queues, but at the same time leave us with insufficient
resources for starting all VFs.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When RoCE is enabled on a given L2 interface, the interrupt lines
are divided equally between L2 and RoCE -
But in case number of lines needed for RoCE is limited by number
of available CNQs, we can utilize the additional lines for L2.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Management firmware and driver are meant to be both backward and forward
compatibile with each other.

If a new mangement firmware would work with an older driver,
it's possible that driver would receive indications which are meaningless
to it. That's perfectly acceptible from the firmware part - so no need to
log such messages at default verbosity; That would only serve to confuse
users.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The management firmware is running on a Big Endian processor,
and when running on LE platform HW is configured to swap access
to memory shared between management firmware and driver on
32-bit granulariy.

As a result, for matters of simplicity most of the APIs between
driver and management firmware are based on 32-bit variables.
MAC settings are one exception, as driver needs to fill a byte
array when indicating to management firmware that primary MAC
has changed.
Due to the swap, driver must make sure that the mac that was
provided in byte-order would be translated into native order,
otherwise after the swap the management firmware would read
it swapped.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver interaction with management firmware involves a union
of all the data-members relating to the commands the driver prepares.

Current interface assumes the caller always passes such a union -
but thats cumbersome as well as risky [chancing a stack corruption
in case caller accidentally passes a smaller member instead of union].

Change implementation so that caller could pass a pointer to any
of the members instead of the union.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Interaction of driver -> management firmware is based
on a one-pending mailbox [per interface], and various
mailbox commands need to be synchronized.

Current scheme is messy, and there's a difficulty extending
it as it deals differently with various commands as well as
making assumption on the required behavior for load/unload
requests.

Drop the current scheme into a completion-list-based approach;
Each flow would try sending the command when possible,
allowing one flow to complete another flow's completion and
relieve the mailbox before sending its own command.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this
via NETIF_F_RXCSUM flag.

v1->v2: 'Signed-off-by' tag added.
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warning from unused set_complete variable. And rearrange code
to eliminate unnecessary goto's.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since there already is a special case goto for control messages (skb == NULL)
in netvsc_send, there is no need for later checks in same code path.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The channel inbound lock was not being used at all by the netvsc
device, but the spin_lock was helpful by providing necessary
barrier before waiting.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than a lock and variable, use a refcount_t to keep track
of the number of sub channels.  Don't need to wait for subchannels
on device removal since wait was already done in device_add.

Also fix the error handling; don't wait forever in case of
an error on request to create sub channels.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is cleaner to use RCU protected pointer (nvdev_ctx->nvdev)
to indicate device is in removed state, rather than having a separate
boolean flag. By using the pointer the context can be checked
by static checkers and dynamic lockdep.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netvsc driver has an internal structure (netvsc_device) which
is created when device is opened and released when device is closed.
And also opened/released when MTU or number of channels change.

Since this is referenced in the receive and transmit path, it is
safer to use RCU to protect/prevent use after free problems.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default number of maximum channels should be limited to the
number of cpus available on the numa node of the primary channel.
This also makes sure maximum channels <= num_online_cpus
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If device is not up, then changing MTU (or number of channels)
should not re-enable the device.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using NAPI, the single stream performance declined signifcantly
because the poll routine was updating host after every burst
of packets. This excess signalling caused host throttling.

This fix restores the old behavior. Host is only signalled
after the ring has been emptied.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there are no egress packets pending, then don't look for tx completions
in napi poll.  Also, fix broken tx queue wakeup logic.
Signed-off-by: NVSR Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NSatanand Burla <satananda.burla@cavium.com>
Signed-off-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add workqueue that is periodically run to try to allocate RX buffers in OOM
conditions in PF and VF.
Signed-off-by: NSatanand Burla <satananda.burla@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Presumably if there is an "add" function, there is also a "del"
function.  But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed review comments from the previous patch-set.

- changed return value check of platform_get_irq() to < 0
- replaced devm_request(free)_irq() calls by request(free)_irq() since
  they are called from open() and close()
- changed sizeof(struct mystruct) to sizeof(*mystruct)
- reduced indentation on tx_timeout()
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed port reset sequence by adding ECC init.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added basic ethtool support.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added phy management support by using phy abstraction layer APIs.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma operation mode configuration routine was wrongly moved to a
function (stmmac_mtl_configuration) that is only executed if the
core version is >= 4.00.

Fixes: 6deee222 ("net: stmmac: prepare dma op mode config for multiple queues")
Reported-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we no longer need to keep the FW enabled for .ndo_close()
to work we can always stop FW after reconfiguration failure.
This seems to make most FWs more resilient to faults (at least
in error injection scenarios).
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device open and close handlers check if the device is already
in the desired state.  Thanks to our reconfig infrastructure
this should not be necessary, there doesn't seem to be any
code in the driver which depends on it.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of ring full or DMA mapping error remember to flush xmit_more
delayed kicks.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP6000 doesn't use queue pointers/doorbells for RX, it uses
'done' bit in descriptors.  Remove the pointers from data structures.
Since we are saving space in rx_ring structure make fields we
previously compressed to 16bits word size again.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warning which was using netdev_warn() instead of dev_warn()
to early.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When acquiring an area fails we can't call function doing both
release and free.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Core should detect when someone is trying to request an access
window which is too large for a given type of access.  Otherwise
the requester will be put on a wait queue for ever without any
error message.

Add const qualifiers to clarify that we are only looking at read-
-only members in relevant functions.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When signal interrupts waiting for an area to become available
we assume success.  Pay attention to the return code.  Unpack
the code a little bit to make it more readable.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

msleep_interruptible() returns time left to wait, not error
code.  Return ERESTARTSYS when interrupted.

While at it correct a comment and make the polling a bit
more aggressive.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We shouldn't access area_cache_list without its lock even
to check if it's empty.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>