This is meant to fix a bug in which we were not checking for pre-existing
VFs if we were not setting the max_vfs value at driver load.  What happens
now is that we always call ixgbe_enable_sriov and this checks for
pre-existing VFs ore requested VFs prior to deciding on no SR-IOV.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The replacement of spin_lock_irq/spin_unlock_irq pair in interrupt
handler by spin_lock_irqsave/spin_lock_irqrestore pair.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NDenis Efremov <yefremov.denis@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jesse Gross says:

====================
A few bug fixes and small enhancements for net-next/3.6.
 ...
Ansis Atteka (1):
      openvswitch: Do not send notification if ovs_vport_set_options() failed

Ben Pfaff (1):
      openvswitch: Check gso_type for correct sk_buff in queue_gso_packets().

Jesse Gross (2):
      openvswitch: Enable retrieval of TCP flags from IPv6 traffic.
      openvswitch: Reset upper layer protocol info on internal devices.

Leo Alterman (1):
      openvswitch: Fix typo in documentation.

Pravin B Shelar (1):
      openvswitch: Check currect return value from skb_gso_segment()

Raju Subramanian (1):
      openvswitch: Replace Nicira Networks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were using a special key "0" for all loopback and point-to-point
device neigh lookups under ipv4, but we wouldn't use that special
key for the neigh creation.

So basically we'd make a new neigh at each and every lookup :-)

This special case to use only one neigh for these device types
is of dubious value, so just remove it entirely.
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLeo Alterman <lalterman@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

At the point where it was used, skb_shinfo(skb)->gso_type referred to a
post-GSO sk_buff.  Thus, it would always be 0.  We want to know the pre-GSO
gso_type, so we need to obtain it before segmenting.

Before this change, the kernel would pass inconsistent data to userspace:
packets for UDP fragments with nonzero offset would be passed along with
flow keys that indicate a zero offset (that is, the flow key for "later"
fragments claimed to be "first" fragments).  This inconsistency tended
to confuse Open vSwitch userspace, causing it to log messages about
"failed to flow_del" the flows with "later" fragments.
Signed-off-by: NBen Pfaff <blp@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Fix return check typo.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

When io access mode is enabled by BOOTROM or BIOS for AR8152 v2.1,
the register can't be read/write by memory access mode.
Clearing Bit 8  of Register 0x21c could fixed the issue.
Signed-off-by: NCloud Ren <cjren@qca.qualcomm.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a crash
tun_chr_close -> netdev_run_todo -> tun_free_netdev -> sk_release_kernel ->
sock_release -> iput(SOCK_INODE(sock))
introduced by commit 1ab5ecb9

The problem is that this socket is embedded in struct tun_struct, it has
no inode, iput is called on invalid inode, which modifies invalid memory
and optionally causes a crash.

sock_release also decrements sockets_in_use, this causes a bug that
"sockets: used" field in /proc/*/net/sockstat keeps on decreasing when
creating and closing tun devices.

This patch introduces a flag SOCK_EXTERNALLY_ALLOCATED that instructs
sock_release to not free the inode and not decrement sockets_in_use,
fixing both memory corruption and sockets_in_use underflow.

It should be backported to 3.3 an 3.4 stabke.
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Override the metrics with rt_pmtu
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jerr Kirsher says:

====================
This series contains updates to ixgbe.
 ...
Alexander Duyck (9):
  ixgbe: Use VMDq offset to indicate the default pool
  ixgbe: Fix memory leak when SR-IOV VFs are direct assigned
  ixgbe: Drop references to deprecated pci_ DMA api and instead use
    dma_ API
  ixgbe: Cleanup configuration of FCoE registers
  ixgbe: Merge all FCoE percpu values into a single structure
  ixgbe: Make FCoE allocation and configuration closer to how rings
    work
  ixgbe: Correctly set SAN MAC RAR pool to default pool of PF
  ixgbe: Only enable anti-spoof on VF pools
  ixgbe: Enable FCoE FSO and CRC offloads based on CAPABLE instead of
    ENABLED flag
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
This patchset represents the way I walked when I was adding multiqueue
support for team driver.

Jiri Pirko (6):
  net: honour netif_set_real_num_tx_queues() retval
  rtnl: allow to specify different num for rx and tx queue count
  rtnl: allow to specify number of rx and tx queues on device creation
  net: rename bond_queue_mapping to slave_dev_queue_mapping
  bond_sysfs: use ream_num_tx_queues rather than params.tx_queue
  team: add multiqueue support
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Largely copied from bonding code.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since now number of tx queues can be specified during bond instance
creation and therefore it may differ from params.tx_queues, use rather
real_num_tx_queues for boundary check.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As this is going to be used not only by bonding.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces IFLA_NUM_TX_QUEUES and IFLA_NUM_RX_QUEUES by
which userspace can set number of rx and/or tx queues to be allocated
for newly created netdevice.
This overrides ops->get_num_[tr]x_queues()
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also cut out unused function parameters and possible err in return
value.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In netif_copy_real_num_queues() the return value of
netif_set_real_num_tx_queues() should be checked.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modern TCP stack highly depends on tcp_write_timer() having a small
latency, but current implementation doesn't exactly meet the
expectations.

When a timer fires but finds the socket is owned by the user, it rearms
itself for an additional delay hoping next run will be more
successful.

tcp_write_timer() for example uses a 50ms delay for next try, and it
defeats many attempts to get predictable TCP behavior in term of
latencies.

Use the recently introduced tcp_release_cb(), so that the user owning
the socket will call various handlers right before socket release.

This will permit us to post a followup patch to address the
tcp_tso_should_defer() syndrome (some deferred packets have to wait
RTO timer to be transmitted, while cwnd should allow us to send them
sooner)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: John Heffner <johnwheffner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When/if sysctl_tcp_abc > 1, we expect to increase cwnd by 2 if the
received ACK acknowledges more than 2*MSS bytes, in tcp_slow_start()

Problem is this RFC 3465 statement is not correctly coded, as
the while () loop increases snd_cwnd one by one.

Add a new variable to avoid this off-by one error.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a missing roundup_pow_of_two(), since tcpmhash_entries is not
guaranteed to be a power of two.

Uses hash_32() instead of custom hash.

tcpmhash_entries should be an unsigned int.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Applied to a set of static inline functions in tcp_input.c
Signed-off-by: NVijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use PCI_VENDOR_ID_INTEL from pci_ids.h instead of creating its own
vendor ID #define.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use PCI_VENDOR_ID_INTEL from pci_ids.h instead of creating its own
vendor ID #define.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove myself from myri10ge MAINTAINERS list
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
the fifth pull request for upcoming v3.6 net-next cleans up and
improves the janz-ican3 driver (6 patches by Ira W. Snyder, one by me).
A patch by Steffen Trumtrar adds imx53 support to the flexcan driver.
And another patch by me, which marks the bit timing constant in the CAN
drivers as "const".
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

The Janz VMOD-ICAN3 hardware has support for one shot packet
transmission. This means that a packet will be attempted to be sent
once, with no automatic retries.

The SocketCAN core has a controller-wide setting for this mode:
CAN_CTRLMODE_ONE_SHOT. The Janz VMOD-ICAN3 hardware supports this flag
on a per-packet level, but the SocketCAN core does not.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

If the bus error quota is set to infinite and the host CPU cannot keep
up, the Janz VMOD-ICAN3 firmware will stop responding to control
messages until the controller is reset.

The firmware will automatically stop sending bus error messages when the
quota is reached, and will only resume sending bus error messages when
the quota is re-set to a positive value.

This limitation is worked around by setting the bus error quota to one
message, and then re-setting the quota to one message every time a bus
error message is received. By doing this, the firmware never stops
responding to control messages. The CAN bus can be reset without a
hard-reset of the controller card.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The Janz VMOD-ICAN3 firmware does not support any sort of TX-done
notification or interrupt. The driver previously used the hardware
loopback to attempt to work around this deficiency, but this caused all
sockets to receive all messages, even if CAN_RAW_RECV_OWN_MSGS is off.

Using the new function ican3_cmp_echo_skb(), we can drop the loopback
messages and return the original skbs. This fixes the issues with
CAN_RAW_RECV_OWN_MSGS.

A private skb queue is used to store the echo skbs. This avoids the need
for any index management.

Due to a lack of TX-error interrupts, bus errors are permanently
enabled, and are used as a TX-error notification. This is used to drop
an echo skb when transmission fails. Bus error packets are not generated
if the user has not enabled bus error reporting.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The error and byte counter statistics were being incremented
incorrectly. For example, a TX error would be counted both in tx_errors
and rx_errors.

This corrects the problem so that tx_errors and rx_errors are only
incremented for errors caused by packets sent to the bus. Error packets
generated by the driver are not counted.

The byte counters are only increased for packets which are actually
transmitted or received from the bus. Error packets generated by the
driver are not counted.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch cleans up the ICAN3 to Linux CAN frame and vice versa
conversion functions:

- RX: Use get_can_dlc() to limit the dlc value.
- RX+TX: Don't copy the whole frame, only copy the amount of bytes
  specified in cf->can_dlc.
Acked-by: NIra W. Snyder <iws@ovro.caltech.edu>
Tested-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The commit which added the janz-ican3 driver and commit
3ccd4c61 "can: Unify droping of invalid tx skbs and netdev stats" were
committed into mainline Linux during the same merge window.

Therefore, the addition of this code to the janz-ican3 driver was
forgotten. This patch adds the expected code.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The code which used this variable was removed during review, before the
driver was added to mainline Linux. It is now dead code, and can be
removed.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds support for a second clock to the flexcan driver. On
modern freescale ARM cores like the imx53 and imx6q two clocks ("ipg"
and "per") must be enabled in order to access the CAN core.

In the original driver, the clock was requested without specifying the
connection id, further all mainline ARM archs with flexcan support
(imx28, imx25, imx35) register their flexcan clock without a
connection id, too.

This patch first renames the existing clk variable to clk_ipg and
converts it to devm for easier error handling. The connection id "ipg"
is added to the devm_clk_get() call. Then a second clock "per" is
requested. As all archs don't specify a connection id, both clk_get
return the same clock. This ensures compatibility to existing flexcan
support and adds support for imx53 at the same time.

After this patch hits mainline, the archs may give their existing
flexcan clock the "ipg" connection id and implement a dummy "per"
clock.

This patch has been tested on imx28 (unmodified clk tree) and on imx53
with a seperate "ipg" and "per" clock.

Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: NHui Wang <jason77.wang@gmail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch marks the bittiming_const pointer as in the struct can_pric as
"const". This allows us to mark the struct can_bittiming_const in the CAN
drivers as "const", too.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Instead of only setting the FCOE segmentation offload and CRC offload flags
if we enable FCoE, we could just set them always since there are no
modifications needed to the hardware or adapter FCoE structure in order to
use these features.

The advantage to this is that if FCoE enablement fails, for example because
SR-IOV was enabled on 82599, we will still have use of the FCoE
segmentation offload and Tx/Rx CRC offloads which should still help to
improve the FCoE performance.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current logic is enabling anti-spoof on all pools and then clearing
anti-spoof on just the first PF pool.  The correct approach is to only set
anti-spoof on the VF pools and to leave all of the PF pools unchecked.

This allows for items such as FCoE to use adjacent pools within the PF for
transmit and receive queues without the traffic being blocked by this
security feature.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change corrects an issue in which an FCoE enabled adapter was always
setting the FCoE SAN MAC MPSAR register to 0x1.  This results in the first
VF being assigned the SAN MAC address in the case of SR-IOV and as such is
incorrect.  To resolve this I am adding a new function that will update the
SAN MAC pool address after reset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the behavior of the FCoE configuration so that it is
much closer to how the main body of the ixgbe driver works for ring
allocation.

The first piece is the ixgbe_fcoe_ddp_enable/disable calls.  These allocate
the percpu values and if successful set the fcoe_ddp_xid value indicating
that we can support DDP.

The next piece is the ixgbe_setup/free_ddp_resources calls.  These are
called on open/close and will allocate and free the DMA pools.

Finally ixgbe_configure_fcoe is now just register configuration.  It can go
through and enable the registers for the FCoE redirection offload, and FIP
configuration without any interference from the DDP pool allocation.

The net result of all this is two fold.  First it adds a certain amount of
exception handling.  So for example if ixgbe_setup_fcoe_resources fails we
will actually generate an error in open and refuse to bring up the
interface.

Secondly it provides a much more graceful failure case than the previous
model which would skip setting up the registers for FCoE on failure to
allocate DDP resources leaving no Rx functionality enabled instead of just
disabling DDP.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>