Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of checking the queues in a loop with hardcoded sleep times
inbetween, use a wait queue to trigger queue checks after the tx
processing tasklet has run.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When operating in client mode, the short period of time between scanning
and associating is often enough to put the hardware through several
FULL-SLEEP <-> AWAKE transitions, each wakeup requiring a reset to fully
recover the hardware.
This is completely unnecessary and can easily be avoided by deferring
the switch to full sleep.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the PLL is turned off for AR9485 when
switching to a low power state, but AR9485 has an issue
where the card will become unresponsive if left idle
for a long time without any traffic. To fix this,
force the PLL to always be on using a different initval
array, ar9485_1_1_pll_on_cdr_on_clkreq_disable_L1.

This is done for most of the AR9485 based cards
like HB125, WB225 etc. but certain models require the
feature to be turned off. Identify such cards and use
default values for them.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use correct width enums when setup
radar_detect_widths for DFS.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX99 support enables Specific Absorption Rate (SAR) testing.
SAR is the unit of measurement for the amount of radio frequency(RF)
absorbed by the body when using a wireless device. The RF
exposure limits used are expressed in the terms of SAR, which is a
measure of the electric and magnetic field strength and power density
for transmitters operating at frequencies from 300 kHz to 100 GHz.

Regulatory bodies around the world require that wireless device
be evaluated to meet the RF exposure limits set forth in the
governmental SAR regulations.

In the examples below, for more bit rate options see the iw TX bitrate
setting documentation:

http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates

Example usage:

iw phy phy0 interface add moni0 type monitor
ip link set dev moni0 up

iw dev moni0 set channel 36 HT40+
iw set bitrates mcs-5 4

echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power
echo 1  > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kill of using ath9k_hw_common() function
in dfs detector code.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not exposed as a configuration option anyway
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rework its wrapper function to make it more generic, using it as a
replacement for previous calls to ath9k_cmn_update_ichannel.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no shared code for handling both rx and tx buffers, and tx
buffers require a lot more metadata than rx buffers.
Using a separate data structure for rx reduces memory usage and improves
cache footprint.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are 2 types of WB335 cards, 1-antenna and 2-antenna.
Identify them based on PCI subsystem IDs, this will be used
for MCI/BTCOEX tweaks.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These cards are based on WB335/AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PCIE Workaround register (AR_WA/0x4004) is used to handle
various hardware quirks. For AR9002 chips, AR_WA_D3_L1_DISABLE
is used to prevent the HW from automatically entering L1 state
when D3 is enforced.

AR_WA_D3_L1_DISABLE has to be enabled for a few AR9280 based
cards, mark them based on their PCI subdevice/subvendor IDs
and enforce it in ar9002_hw_configpcipowersave().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This improves RX diversity and performance for AR9485.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.

This fixes a reported brcmsmac regression introduced in
commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6
"mac80211/minstrel_ht: fix cck rate sampling"

Cc: stable@vger.kernel.org # 3.10
Reported-by: NTom Gundersen <teg@jklm.no>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

CSA is only enabled for one interface, but the same limitation applies
for mac80211 too. It checks whether the beacon has been sent (different
approaches for non-EDMA-enabled and EDMA-enabled devices), and completes
the channel switch after that.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To enable support for 5/10 MHz, some internal functions must be
converted from using the (old) channel_type to chandef. This is a good
chance to change all remaining occurences.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BTCOEX has to be *disabled* for WLAN RX diversity to
work on combo cards.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS198/CUS230 cards require a custom value to be
programmed into the SWCOM register. Assign this during
init time.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make use of this capability to restrict the usage of the
debugfs file and modparam using which this feature can
be enabled.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For single-chain WLAN+BT cards, the BT antenna can be used for
WLAN RX when the BT interface is disabled. Rename the modparam
"antenna_diversity" to "bt_ant_diversity" to clarify this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS198/CUS230 need a few tweaks in the antenna diversity
algorithm to accomodate RSSI variation. Add a couple
of knobs to control low RSSI threshold and fast antenna
diversity bias values.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since platform support is required for WoW, identify and
and enable Wow only for supported cards.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS217 is a card based on AR9462.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS198 and CUS230 are similar cards, both
are AR9485 + xLNA solutions. But, the subsystem IDs
differ - identify CUS230 explicitly to make things
clearer.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.

Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201

Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the UAPSD hardware queue to get PS-Poll responses out as fast as
possible and without backoff.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.

An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191

Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.

Cc: stable@vger.kernel.org
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.

Cc: stable@vger.kernel.org
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The only card with which WoW has been tested and verified is
AR9462. Do not enable it for all cards since WoW is really quirky
and needs to be tested properly with each chip.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch make use of STBC flag in DMA RX descriptor.
Only devices after ar9280 can provide this information.

If card support it we will set HAVE_STBC flag, to show
clint programm thet STBC is supported but not received.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This option has not been enabled by default in any
distribution, has never been enabled in OpenWrt and no developer
has asked for this information in a bug report.

Dumping pages of random values doesn't help debugging,
remove this option (along with the vmalloc() abuse).
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>