These multi-lines comments do not follow the standard kernel coding
style. In fact, they are not useful comments, so get rid of them.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Replace of_get_named_gpio_flags with of_get_named_gpio because
the latter has less parameters, which improves code readability.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGao Pan <b54642@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

When DMA cannot be used, it is better to state that the I2C controller
will operate in PIO mode.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

In our former i2c driver, i2c clk is enabled and disabled in
xfer function, which contributes to power saving. However,
the clk enable process brings a busy wait delay until the core
is stable. As a result, the performance is sacrificed.

To weigh the power consumption and i2c bus performance, runtime
pm is the good solution for it. The clk is enabled when a i2c
transfer starts, and disabled after a specifically defined delay.

If CONFIG_PM is disabled the net result of this patch is that the
clock is never disabled.

Without the patch the test case (many eeprom reads) executes with approx:
real 1m7.735s
user 0m0.488s
sys 0m20.040s

With the patch the same test case (many eeprom reads) executes with approx:
real 0m54.241s
user 0m0.440s
sys 0m5.920s
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGao Pan <b54642@freescale.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
[wsa: sorted includes]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.

In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.

The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: NGao Pan <b54642@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

drivers/i2c/busses/i2c-imx.c:978:2: error: implicit declaration of
function ‘pinctrl_select_state’ [-Werror=implicit-function-declaration]
  pinctrl_select_state(i2c_imx->pinctrl, i2c_imx->pinctrl_pins_gpio);
  ^
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

According to Documentation/i2c/fault-codes the response to a bus NACK
should be -ENXIO, so fix the error code.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.

Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGao Pan <b54642@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The platform_device_id is not modified by these drivers and core uses it
as const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

return type of wait_for_completion_timeout is unsigned long not int.
An appropriate variable of type unsigned long is introduced and the
assignments fixed up.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch fixes up some whitespace issues and addresses a few
checkpatch warnings.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The ret variable is set and never used in the error path of i2c_imx_dma_request.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

wait_for_completion_timeout does not return negative values so
"result" handling here should be simplified to cover the actually
possible cases only.
Signed-off-by: NNicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NYao Yuan <yao.yuan@freescale.com>

Add dma support for i2c. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
DMA is optional, even DMA request unsuccessfully, i2c can also work well.
Signed-off-by: NYuan Yao <yao.yuan@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: NYuan Yao <yao.yuan@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

According to Documentation/CodingStyle - Chapter 14:

"The preferred form for passing a size of a struct is the following:

	p = kmalloc(sizeof(*p), ...);

The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."

So do it as recommeded.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

We have a central copy of the GPL for that. Some addresses were already
outdated.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

In the case of errors during probe, we should disable i2c_imx->clk.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

According to the i.mx spec, for multimaster mode, if I2C is
enabled when the bus is busy and asserts start, hardware inhibits
the transmission, clears MSTA without signaling a stop, generate
an interrupt, and set I2C_I2SR[IAL] to indicate a failed attempt
to engage the bus, which means arbitration lost. In this case,
we should first test I2C_I2SR[IAL], and clear this bit if it is
set, and then I2C controller default to slave receive mode.

This patch check the IAL bit every time before an I2c transmission.
if IAL is set, clear it and make I2C controller to default mode.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Fixes the following by using %pR:

drivers/i2c/busses/i2c-imx.c: In function i2c_imx_probe()
drivers/i2c/busses/i2c-imx.c:689:2: warning: format 0x%x expects argument
of type unsigned int, but argument 4 has type resource_size_t [-Wformat=]
  dev_dbg(&i2c_imx->adapter.dev, "device resources from 0x%x to 0x%x\n",
  ^
...
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message. For example,
k.alloc and v.alloc failures use dump_stack().
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Since IMX serial SOCs support low bus freq mode, some clocks freq
may change to save power. I2C needs to check the clock source and
update the divider.

For example:
i.MX6SL I2C clk is from IPG_PERCLK which is sourced from IPG_CLK.
Under normal operation, IPG_CLK is 66MHz, ipg_perclk is at 22MHz.
In low bus freq mode, IPG_CLK is at 12MHz and IPG_PERCLK is down
to 4MHz. So the I2C driver must update the divider register for
each transaction when the current IPG_PERCLK is not equal to the
clock of previous transaction.
Signed-off-by: NFugang Duan  <B38611@freescale.com>
[wsa: removed an outdated comment and simplified debug output]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Test i2c device Maxim max44009, datasheet is located at:
http://www.maximintegrated.com/datasheet/index.mvp/id/7175

The max44009 support repeat operation like:
read -> repeat restart -> read/write

The current i2c imx host controller driver don't support this
operation that causes i2c bus hang due to "MTX" is cleared in
.i2c_imx_read(). If "read" is the last message there have no problem,
so the current driver supports all SMbus operation like:
write -> repeat restart -> read/write

IMX i2c controller for master receiver has some limitation:
- If it is the last byte for one operation, it must generate STOP
  signal before read I2DR to prevent controller from generating another
  clock cycle.
- If it is the last byte in the read, and then do repeat restart, it must
  set "MTX" before read I2DR to prevent controller from generating another
  extra clock cycle.

The patch is to fix the issue.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The smbus block read is not currently supported for imx i2c devices.
This patchset adds the support to imx i2c bus so that blocks of data
can be read using SMbus block reads.(using i2c_smbus_read_block_data()
function from the i2c_core.c.). Tested with 3.10.9 kernel.
Reviewed-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NKaushal Butala <kaushalkernelmailinglist@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

smatch rightfully says:
drivers/i2c/busses/i2c-imx.c:610 i2c_imx_probe() info: why not propagate 'irq' from platform_get_irq() instead of (-2)?
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add Freescale Vybrid VF610 I2C controller support to
imx I2C driver framework.
Signed-off-by: NJason Jin <Jason.jin@freescale.com>
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This add struct imx_i2c_hwdata to hold more quirks data
which may vary between SoCs, thus the driver can operate
on more differences to support more SoCs.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This add bits operation macro that differ between SoCs.
Interrupt flags clear operation in I2SR differ between SoCs:
write zero to clear(w0c) INT flag on i.MX,
but write one to clear(w1c) INT flag on Vybrid.
I2C module enable operation in I2CR also differ between SoCs:
set I2CR_IEN bit enable the module on i.MX,
but clear I2CR_IEN bit enable the module on Vybrid.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

the I2C register offset may different between SoCs,
to provid support for all these chips, split the
register offset into a fixed base address and a
variable shift value, then the full register offset
will be calculated by
reg_off = ( reg_base_addr << reg_shift)
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

wrap the readb(), writeb() into inline function calls.
It would make the driver more clearer to support platform
with different register offset.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The id_entry field should be changed by platform driver core,
driver should prevent changing it derectly. Use local variable
to save and extract platform_device_id info of the dts devices
instead.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The module clk should be enabled before write to
its register in probe(), and the clk can be disabled
after.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

using struct representing the i2c clk{div, val} pair would
make the i2c_clk_div array more clear.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allow udev to autoload the module when booting with device-tree
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>