On POWER, storage caching is usually configured via the MMU - attributes
such as cache-inhibited are stored in the TLB and the hashed page table.

This makes correctly performing cache inhibited IO accesses awkward when
the MMU is turned off (real mode).  Some CPU models provide special
registers to control the cache attributes of real mode load and stores but
this is not at all consistent.  This is a problem in particular for SLOF,
the firmware used on KVM guests, which runs entirely in real mode, but
which needs to do IO to load the kernel.

To simplify this qemu implements two special hypercalls, H_LOGICAL_CI_LOAD
and H_LOGICAL_CI_STORE which simulate a cache-inhibited load or store to
a logical address (aka guest physical address).  SLOF uses these for IO.

However, because these are implemented within qemu, not the host kernel,
these bypass any IO devices emulated within KVM itself.  The simplest way
to see this problem is to attempt to boot a KVM guest from a virtio-blk
device with iothread / dataplane enabled.  The iothread code relies on an
in kernel implementation of the virtio queue notification, which is not
triggered by the IO hcalls, and so the guest will stall in SLOF unable to
load the guest OS.

This patch addresses this by providing in-kernel implementations of the
2 hypercalls, which correctly scan the KVM IO bus.  Any access to an
address not handled by the KVM IO bus will cause a VM exit, hitting the
qemu implementation as before.

Note that a userspace change is also required, in order to enable these
new hcall implementations with KVM_CAP_PPC_ENABLE_HCALL.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
[agraf: fix compilation]
Signed-off-by: NAlexander Graf <agraf@suse.de>

Export __spin_yield so that the arch_spin_unlock() function can
be invoked from a module. This will be required for modules where
we want to take a lock that is also is acquired in hypervisor
real mode. Because we want to avoid running any lockdep code
(which may not be safe in real mode), this lock needs to be
an arch_spinlock_t instead of a normal spinlock.
Signed-off-by: NSuresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Pull staging driver updates from Greg KH:
 "Here's the big staging driver patchset for 4.1-rc1.

  There's a lot of patches here, the Outreachy application period
  happened during this development cycle, so that means that there was a
  lot of cleanup patches accepted.  Other than the normal coding style
  and sparse fixes here, there are some driver updates and work toward
  making some of the drivers into "mergable" shape (like the Unisys
  drivers.)

  All of these have been in linux-next for a while"

* tag 'staging-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1214 commits)
  staging: lustre: orthography & coding style
  staging: lustre: lnet: lnet: fix error return code
  staging: lustre: fix sparse warning
  Revert "Staging: sm750fb: Fix C99 Comments"
  Staging: rtl8192u: use correct array for debug output
  staging: rtl8192e: Remove dead code
  staging: rtl8192e: Comment cleanup (style/format)
  staging: rtl8192e: Fix indentation in rtllib_rx_auth_resp()
  staging: rtl8192e: Decrease nesting of rtllib_rx_auth_resp()
  staging: rtl8192e: Divide rtllib_rx_auth()
  staging: rtl8192e: Fix PRINTK_WITHOUT_KERN_LEVEL warnings
  staging: rtl8192e: Fix DO_WHILE_MACRO_WITH_TRAILING_SEMICOLON warning
  staging: rtl8192e: Fix BRACES warning
  staging: rtl8192e: Fix LINE_CONTINUATIONS warning
  staging: rtl8192e: Fix UNNECESSARY_PARENTHESES warnings
  staging: rtl8192e: remove unused EXPORT_SYMBOL_RSL macro
  staging: rtl8192e: Fix RETURN_VOID warnings
  staging: rtl8192e: Fix UNNECESSARY_ELSE warning
  staging: rtl8723au: Remove unneeded comments
  staging: rtl8723au: Use __func__ in trace logs
  ...

Pull driver core updates from Greg KH:
 "Here's the driver-core / kobject / lz4 tree update for 4.1-rc1.

  Everything here has been in linux-next for a while with no reported
  issues.  It's mostly just coding style cleanups, with other minor
  changes in here as well, nothing big"

* tag 'driver-core-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
  debugfs: allow bad parent pointers to be passed in
  stable_kernel_rules: Add clause about specification of kernel versions to patch.
  kobject: WARN as tip when call kobject_get() to a kobject not initialized
  lib/lz4: Pull out constant tables
  drivers: platform: parse IRQ flags from resources
  driver core: Make probe deferral more quiet
  drivers/core/of: Add symlink to device-tree from devices with an OF node
  device: Add dev_of_node() accessor
  drivers: base: fw: fix ret value when loading fw
  firmware: Avoid manual device_create_file() calls
  drivers/base: cacheinfo: validate device node for all the caches
  drivers/base: use tabs where possible in code indentation
  driver core: add missing blank line after declaration
  drivers: base: node: Delete space after pointer declaration
  drivers: base: memory: Use tabs instead of spaces
  firmware_class: Fix whitespace and indentation
  drivers: base: dma-mapping: Erase blank space after pointer
  drivers: base: class: Add a blank line after declarations
  attribute_container: fix missing blank lines after declarations
  drivers: base: memory: Fix switch indent
  ...

Pull USB driver updates from Greg KH:
 "Here's the big USB (and PHY) driver patchset for 4.1-rc1.

  Everything here has been in linux-next, and the full details are below
  in the shortlog.  Nothing major, just the normal round of new
  drivers,api updates, and other changes, mostly in the USB gadget area,
  as usual"

* tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (252 commits)
  drivers/usb/core: devio.c: Removed an uneeded space before tab
  usb: dwc2: host: sleep USB_RESUME_TIMEOUT during resume
  usb: chipidea: debug: add low power mode check before print registers
  usb: chipidea: udc: bypass pullup DP when gadget connect in OTG fsm mode
  usb: core: hub: use new USB_RESUME_TIMEOUT
  usb: isp1760: hcd: use new USB_RESUME_TIMEOUT
  usb: dwc2: hcd: use new USB_RESUME_TIMEOUT
  usb: host: sl811: use new USB_RESUME_TIMEOUT
  usb: host: r8a66597: use new USB_RESUME_TIMEOUT
  usb: host: oxu210hp: use new USB_RESUME_TIMEOUT
  usb: host: fusbh200: use new USB_RESUME_TIMEOUT
  usb: host: fotg210: use new USB_RESUME_TIMEOUT
  usb: host: isp116x: use new USB_RESUME_TIMEOUT
  usb: musb: use new USB_RESUME_TIMEOUT
  usb: host: uhci: use new USB_RESUME_TIMEOUT
  usb: host: ehci: use new USB_RESUME_TIMEOUT
  usb: host: xhci: use new USB_RESUME_TIMEOUT
  usb: define a generic USB_RESUME_TIMEOUT macro
  usb: musb: dsps: fix build on i386 when COMPILE_TEST is set
  ehci-hub: use USB_DT_HUB
  ...

Pull cgroup updates from Tejun Heo:
 "Nothing too interesting.  Rik made cpuset cooperate better with
  isolcpus and there are several other cleanup patches"

* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset, isolcpus: document relationship between cpusets & isolcpus
  cpusets, isolcpus: exclude isolcpus from load balancing in cpusets
  sched, isolcpu: make cpu_isolated_map visible outside scheduler
  cpuset: initialize cpuset a bit early
  cgroup: Use kvfree in pidlist_free()
  cgroup: call cgroup_subsys->bind on cgroup subsys initialization

Pull libata updates from Tejun Heo:

 - Hannes's patchset implements support for better error reporting
   introduced by the new ATA command spec.

 - the deperecated pci_ dma API usages have been replaced by dma_ ones.

 - a bunch of hardware specific updates and some cleanups.

* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata: remove deprecated use of pci api
  ahci: st: st_configure_oob must be called after IP is clocked.
  ahci: st: Update the ahci_st DT documentation
  ahci: st: Update the DT example for how to obtain the PHY.
  sata_dwc_460ex: indent an if statement
  libata: Add tracepoints
  libata-eh: Set 'information' field for autosense
  libata: Implement support for sense data reporting
  libata: Implement NCQ autosense
  libata: use status bit definitions in ata_dump_status()
  ide,ata: Rename ATA_IDX to ATA_SENSE
  libata: whitespace fixes in ata_to_sense_error()
  libata: whitespace cleanup in ata_get_cmd_descript()
  libata: use READ_LOG_DMA_EXT
  libata: remove ATA_FLAG_LOWTAG
  sata_dwc_460ex: re-use hsdev->dev instead of dwc_dev
  sata_dwc_460ex: move to generic DMA driver
  sata_dwc_460ex: join messages back
  sata: xgene: add ACPI support for APM X-Gene SATA ports
  ata: sata_mv: add proper definitions for LP_PHY_CTL register values

Pull workqueue updates from Tejun Heo:
 "Workqueue now prints debug information at the end of sysrq-t which
  should be helpful when tracking down suspected workqueue stalls.  It
  only prints out the ones with something currently going on so it
  shouldn't add much output in most cases"

* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: Reorder sysfs code
  percpu: Fix trivial typos in comments
  workqueue: dump workqueues on sysrq-t
  workqueue: keep track of the flushing task and pool manager
  workqueue: make the workqueues list RCU walkable

Pull irq core updates from Thomas Gleixner:
 "Managerial summary:

  Core code:
   - final removal of IRQF_DISABLED
   - new state save/restore functions for virtualization support
   - wakeup support for stacked irqdomains
   - new function to solve the netpoll synchronization problem

 irqchips:
   - new driver for STi based devices
   - new driver for Vybrid MSCM
   - massive cleanup of the GIC driver by moving the GIC-addons to
     stacked irqdomains
   - the usual pile of fixes and updates to the various chip drivers"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
  irqchip: GICv3: Add support for irq_[get, set]_irqchip_state()
  irqchip: GIC: Add support for irq_[get, set]_irqchip_state()
  genirq: Allow the irqchip state of an IRQ to be save/restored
  genirq: MSI: Fix freeing of unallocated MSI
  irqchip: renesas-irqc: Add wake-up support
  irqchip: armada-370-xp: Allow using wakeup source
  irqchip: mips-gic: Add new functions to start/stop the GIC counter
  irqchip: tegra: Add Tegra210 support
  irqchip: digicolor: Move digicolor_set_gc to init section
  irqchip: renesas-irqc: Add functional clock to bindings
  irqchip: renesas-irqc: Add minimal runtime PM support
  irqchip: renesas-irqc: Add more register documentation
  DT: exynos: update PMU binding
  ARM: exynos4/5: convert pmu wakeup to stacked domains
  irqchip: gic: Don't complain in gic_get_cpumask() if UP system
  ARM: zynq: switch from gic_arch_extn to gic_set_irqchip_flags
  ARM: ux500: switch from gic_arch_extn to gic_set_irqchip_flags
  ARM: shmobile: remove use of gic_arch_extn.irq_set_wake
  irqchip: gic: Add an entry point to set up irqchip flags
  ARM: omap: convert wakeupgen to stacked domains
  ...

Pull PCI changes from Bjorn Helgaas:
 "Enumeration
    - Read capability list as dwords, not bytes (Sean O. Stalley)

  Resource management
    - Don't check for PNP overlaps with unassigned PCI BARs (Bjorn Helgaas)
    - Mark invalid BARs as unassigned (Bjorn Helgaas)
    - Show driver, BAR#, and resource on pci_ioremap_bar() failure (Bjorn Helgaas)
    - Fail pci_ioremap_bar() on unassigned resources (Bjorn Helgaas)
    - Assign resources before drivers claim devices (Yijing Wang)
    - Claim bus resources before pci_bus_add_devices() (Yijing Wang)

  Power management
    - Optimize device state transition delays (Aaron Lu)
    - Don't clear ASPM bits when the FADT declares it's unsupported (Matthew Garrett)

  Virtualization
    - Add ACS quirks for Intel 1G NICs (Alex Williamson)

  IOMMU
    - Add ptr to OF node arg to of_iommu_configure() (Murali Karicheri)
    - Move of_dma_configure() to device.c to help re-use (Murali Karicheri)
    - Fix size when dma-range is not used (Murali Karicheri)
    - Add helper functions pci_get[put]_host_bridge_device() (Murali Karicheri)
    - Add of_pci_dma_configure() to update DMA configuration (Murali Karicheri)
    - Update DMA configuration from DT (Murali Karicheri)
    - dma-mapping: limit IOMMU mapping size (Murali Karicheri)
    - Calculate device DMA masks based on DT dma-range size (Murali Karicheri)

  ARM Versatile host bridge driver
    - Check for devm_ioremap_resource() failures (Jisheng Zhang)

  Broadcom iProc host bridge driver
    - Add Broadcom iProc PCIe driver (Ray Jui)

  Marvell MVEBU host bridge driver
    - Add suspend/resume support (Thomas Petazzoni)

  Renesas R-Car host bridge driver
    - Fix position of MSI enable bit (Nobuhiro Iwamatsu)
    - Write zeroes to reserved PCIEPARL bits (Nobuhiro Iwamatsu)
    - Change PCIEPARL and PCIEPARH to PCIEPALR and PCIEPAUR (Nobuhiro Iwamatsu)
    - Verify that mem_res is 64K-aligned (Nobuhiro Iwamatsu)

  Samsung Exynos host bridge driver
    - Fix INTx enablement statement termination error (Jaehoon Chung)

  Miscellaneous
    - Make a shareable UUID for PCI firmware ACPI _DSM (Aaron Lu)
    - Clarify policy for vendor IDs in pci.txt (Michael S. Tsirkin)"

* tag 'pci-v4.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (36 commits)
  PCI: Read capability list as dwords, not bytes
  PCI: layerscape: Simplify platform_get_resource_byname() failure checking
  PCI: keystone: Don't dereference possible NULL pointer
  PCI: versatile: Check for devm_ioremap_resource() failures
  PCI: Don't clear ASPM bits when the FADT declares it's unsupported
  PCI: Clarify policy for vendor IDs in pci.txt
  PCI/ACPI: Optimize device state transition delays
  PCI: Export pci_find_host_bridge() for use inside PCI core
  PCI: Make a shareable UUID for PCI firmware ACPI _DSM
  PCI: Fix typo in Thunderbolt kernel message
  PCI: exynos: Fix INTx enablement statement termination error
  PCI: iproc: Add Broadcom iProc PCIe support
  PCI: iproc: Add DT docs for Broadcom iProc PCIe driver
  PCI: Export symbols required for loadable host driver modules
  PCI: Add ACS quirks for Intel 1G NICs
  PCI: mvebu: Add suspend/resume support
  PCI: Cleanup control flow
  sparc/PCI: Claim bus resources before pci_bus_add_devices()
  PCI: Assign resources before drivers claim devices (pci_scan_root_bus())
  PCI: Fail pci_ioremap_bar() on unassigned resources
  ...

Pull HSI changes from Sebastian Reichel:

 - nokia-modem: support speech data
 - misc fixes

* tag 'hsi-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
  HSI: cmt_speech: fix error return code
  HSI: nokia-modem: Add cmt-speech support
  HSI: cmt_speech: Add cmt-speech driver
  HSI: nokia-modem: fix error return code

Pull power supply and reset changes from Sebastian Reichel:

 - new API for safe access of power supply function attrs

 - devres support for power supply (un)registration

 - new drivers / chips:
     - generic syscon based poweroff driver
     - iio & charger driver for da9150
     - fuel gauge driver for axp288
     - bq27x00: add support for bq27510
     - bq2415x: add support for bq24157s

 - twl4030-madc-battery: convert to iio consumer

 - misc fixes

* tag 'for-v4.1' of git://git.infradead.org/battery-2.6: (66 commits)
  power: twl4030_madc_battery: Add missing MODULE_ALIAS
  power: twl4030-madc-battery: Convert to iio consumer.
  dt: power: Add docs for generic SYSCON poweroff driver.
  power: reset: Add generic SYSCON register mapped poweroff.
  power: max17042_battery: add missed blank
  power: max17042_battery: Use reg type instead of chip type
  power/reset: at91: big endian fixes for atsama5d3x
  power_supply: charger-manager: Fix dereferencing of ERR_PTR
  HID: input: Fix NULL pointer dereference when power_supply_register fails
  power: constify of_device_id array
  power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
  power_supply: 88pm860x_charger: Fix possible NULL pointer dereference and use of initialized variable
  arm: mach-pxa: Decrement the power supply's device reference counter
  mfd: ab8500: Decrement the power supply's device reference counter
  power_supply: bq2415x_charger: Decrement the power supply's device reference counter
  power_supply: 88pm860x_charger: Decrement the power supply's device reference counter
  x86/olpc/xo15/sci: Use newly added power_supply_put API
  x86/olpc/xo1/sci: Use newly added power_supply_put API
  power_supply: charger-manager: Decrement the power supply's device reference counter
  power_supply: Increment power supply use counter when obtaining references
  ...

Pull regulator updates from Mark Brown:
 "Another release, another set of regulator updates.  Not much of it is
  showing up in the code yet but there's been a lot of discussion going
  on about how to enhance the regulator API to work better with modern
  SoCs which have a microcontroller sitting between Linux and the
  hardware.

  I'm hopeful that'll start to come through into mainline for v4.2 but
  it's not quite there for v4.1 - what we do have (along with the usual
  small updates is) is:

   - work from Bjorn Andersson on refactoring the configuration of
     regulator loading interfaces to be useful for use with
     microcontrollers, the existing interfaces were never actually
     useful for anything as-is since nobody was willing to put enough
     data into public code.

   - a summary tree display in debugfs from Heiko Stübner.

   - support for act6000 regulators"

* tag 'regulator-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (34 commits)
  regulator: max8660: Handle empty regulator data
  regulator: output current-limit for all regulators in summary
  regulator: add a summary tree in debugfs
  regulator: qcom: Tidy up probe()
  regulator: qcom: Rework to single platform device
  regulator: qcom: Refactor of-parsing code
  regulator: qcom: Don't enable DRMS in driver
  regulator: max8660: fix assignment of pdata to data that becomes dead
  regulator: Defer lookup of supply to regulator_get
  mfd: max77693: Remove unused structures
  regulator: max77693: Let core parse DT and drop board files support
  regulator: Ensure unique regulator debugfs directory names
  regulator: stw481x: Remove unused fields from struct stw481x
  regulator: palmas: Add has_regen3 check for TPS659038
  regulator: constify of_device_id array
  regulator: fixes for regulator_set_optimum_mode name change
  regulator: Drop temporary regulator_set_optimum_mode wrapper
  usb: phy: phy-msm-usb: Rename regulator_set_optimum_mode
  usb: phy: ab8500-usb: Rename regulator_set_optimum_mode
  ufs: Rename of regulator_set_optimum_mode
  ...

Pull spi updates from Mark Brown:
 "Only one framework update this time around, a change from Lars-Peter
  to move full to pm_ops and remove the legacy bus PM ops.  Otherwise
  it's all driver updates:

   - make the spidev driver complain loudly if registered as spidev with
     DT rather than with a compatible string, hopefully helping people
     avoid making that mistake.

   - error handling and robustness fixes for the Designware and Intel
     MID drivers from Andy Shevchenko.

   - substantial performance improvements for the Raspberry Pi driver
     from Martin Sperl.

   - several new features for spidev_test from Adrian Remonda and Ian
     Abbott"

* tag 'spi-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (75 commits)
  spi: bcm2835: enabling polling mode for transfers shorter than 30us
  spi: bcm2835: transform native-cs to gpio-cs on first spi_setup
  spi: img-spfi: Control CS lines with GPIO
  spi: img-spfi: Reset controller after each message
  spi: img-spfi: Implement a handle_err() callback
  spi: img-spfi: Setup TRANSACTION register before CONTROL register
  spi: Make master->handle_err() callback optional to avoid crashes
  spi: img-spfi: Limit bit clock to 1/4th of input clock
  spi: img-spfi: Implement a prepare_message() callback
  spi: fsl-dspi: Add ~50ns delay between cs and sck
  spi: fsl-dspi: Add cs-sck delays
  spi: fsl-dspi: Fix clock rate scale values
  spi: signedness bug in qspi_trigger_transfer_out_int()
  spi: imx: read back the RX/TX watermark levels earlier
  spi: spi-bfin5xx: Initialize cr_width in bfin_spi_pump_transfers()
  spi: bitbang: only toggle bitchanges
  spi: pxa2xx: missing break in pxa2xx_ssp_get_clk_div()
  spi: fsl-dspi: Fix clock rate scale values
  spi: Using Trigger number to transmit/receive data
  spi: bcm2835: fill FIFO before enabling interrupts to reduce interrupts/message
  ...

Pull regmap update from Mark Brown:
 "Just one patch for regmap this time around, a change from Steven
  Rostedt to prettify the way we're making the regmap internal header
  available to the trace events (it turns out that the trace subsystem
  doesn't actually need to be in trace/events)"

* tag 'regmap-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Move tracing header into drivers/base/regmap

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Add support for marking HPI as broken through devicetree
   - Enable runtime PM management of host devices
   - Remove the ->enable|disable() callbacks
   - Restructure code and cleanups
   - Refreshed some of the MMC sections in MAINTAINERS

  MMC host:
   - dw_mmc: HS400 mode support
   - dw_mmc: Add the cmd11 timer to detect a timeout
   - dw_mmc: Endian agnostic IO accessors
   - dw_mmc: Bugfixes
   - sh_mmcif: Add exclusion between cmd and interrupt
   - omap_hsmmc: Hibernation support
   - omap_hsmmc: Rework and simplify cover/card detect
   - omap_hsmmc: Stop using ->enable|disable() callbacks
   - atmel-mci: Endian agnostic IO
   - sunxi: Enable MMC_CAP_SDIO_IRQ
   - sdhci-st: Add support for the stih407 family silicon
   - sdhci-st: UHS card support in SDR104 mode
   - sdhci-st: HS200 mode support
   - sdhci-esdhc-imx: Use common mmc DT parser
   - sdhci-of-arasan: Use common mmc DT parser
   - sdhci-iproc: Add new driver for Broadcom IPROC SDHCI controller
   - sdhci-tegra: Convert to GPIO descriptors
   - sdhci-tegra: Optmize write_w path for tegra114 and later
   - sdhci-sirf: Update tuning procedure
   - sdhci: Fix card presence logic
   - sdhci: Cleanups and consolidation"

* tag 'mmc-v4.1' of git://git.linaro.org/people/ulf.hansson/mmc: (79 commits)
  mmc: sdhci-st: Update ST SDHCI binding documentation.
  mmc: sdhci-st: Update the quirks for this controller.
  mmc: sdhci-st: Add sdhci_st_set_uhs_signaling function.
  mmc: sdhci-st: Add st_mmcss_cconfig function to configure mmcss glue registers.
  mmc: sdhci-st: Add delay management functions for top registers (eMMC).
  mmc: sdhci-st: Add support for de-asserting reset signal and top regs resource
  mmc: sdhci-st: Add macros for register offsets and bitfields for mmcss glue regs
  mmc: sdhci-esdhc-imx: Call mmc_of_parse()
  mmc: dw_mmc: Add locking around cmd11 timer
  mmc: dw_mmc: Add a return in an unexpected cmd11 timeout
  mmc: dw_mmc: Increase cmd11 timeout to 500ms
  mmc: dw_mmc: fix fifo ordering in big endian
  mmc: dw_mmc: change idmac descriptor files to __le32
  mmc: dw_mmc: make IO accessors endian agnostic
  mmc: core: Convert the error field in struct mmc_command|data into an int
  mmc: sdhci-of-arasan: Call OF parsing for MMC
  mmc: sdhci-pci: fix 64 BIT DMA quirks for rtsx
  mmc: Add support for marking hpi as broken through devicetree
  mmc: sdhci-tegra: convert to use GPIO descriptors
  mmc: omap_hsmmc: use generic slot-gpio isr to manage card detect pin
  ...

Pull EDAC updates from Borislav Petkov:

 - convert a bunch of drivers to static attribute groups (Takashi Iwai)

 - misc cleanups

* tag 'edac_for_4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC: Constify of_device_id array
  EDAC, i82443bxgx: Don't export static symbol
  EDAC, amd64_edac: Get rid of per-node driver instances
  EDAC: Properly unwind on failure path in edac_init()
  EDAC: highbank: Use static attribute groups for sysfs entries
  EDAC: octeon: Use static attribute groups for sysfs entries
  EDAC: mpc85xx: Use static attribute groups for sysfs entries
  EDAC: i7core: Use static attribute groups for sysfs entries
  EDAC: i7core: Return proper error codes for kzalloc() errors
  EDAC: amd64: Use static attribute groups
  EDAC: Allow to pass driver-specific attribute groups
  EDAC: Use static attribute groups for managing sysfs entries
  EDAC: Delete unnecessary checks before pci_dev_put()

Merge tag 'hwmon-for-linus-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "Support for new chips:

   - add support for IT8620E, IT8781F, IT8786E, and IT8790E to it87
     driver

   - add driver for NCT7904

  Functional improvements:

   - support for new devicetree structure in ibmpowernv driver

   - register pwm-fan and gpio-fan drivers as thermal cooling devices

   - various minor cleanup and improvements to it87, nct6775, jc42,
     ibmpex, and coretemp drivers"

* tag 'hwmon-for-linus-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (43 commits)
  hwmon: (pwm-fan) Update the duty cycle inorder to control the pwm-fan
  hwmon: (it87) Use feature macros on sio_data
  hwmon: (ibmpowernv) Fix build error seen for some configurations
  hwmon: (gpio-fan) Move the thermal registration after registration is complete
  hwmon: (ibmpowernv) pretty print labels
  hwmon: (ibmpowernv) add a label attribute
  hwmon: (ibmpowernv) add support for the new device tree
  hwmon: (ibmpowernv) add a helper routine create_hwmon_attr
  hwmon: (it87) Add support for 6th fan of IT8620E
  hwmon: (it87) Add support for IT8620E
  hwmon: (it87) Add support for IT8790E
  hwmon: (it87) Introduce feature flag to reflect internal in7 sensor
  hwmon: (it87) Introduce configuration field for chip suffix
  hwmon: (it87) Fix PWM frequency display for chips with newer PWM control
  hwmon: (it87) Fix pwm sysfs attribute removal
  hwmon: (ibmpowernv) do not use the OPAL index for hwmon attribute names
  hwmon: (ibmpowernv) change create_hwmon_attr_name() prototype
  hwmon: (ibmpowernv) add a convert_opal_attr_name() routine
  hwmon: (ibmpowernv) add a get_sensor_type() routine
  hwmon: (ibmpowernv) replace AMBIENT_TEMP by TEMP
  ...

Pull avr32 fix from Hans-Christian Egtvedt.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
  avr32: fix integer overflow in ELF_ET_DYN_BASE

Pull m68k updates from Geert Uytterhoeven.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/mac: Fix out-of-bounds array index in OSS IRQ source initialization
  m68k/pci: Remove a superflous KERN_ERR
  m68k/defconfig: Update defconfigs for v4.0-rc1
  m68k/q40: Make NE2000 builtin instead of modular
  m68k: Remove FSF address

Pull x86 vdso changes from Ingo Molnar:
 "Misc vDSO updates"

* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vdso: Remove x32 intermediates during 'make clean'
  x86/vdso: Teach 'make clean' to remove generated vdso-image-*.c files
  x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
  x86/vdso: Fix the x86 vdso2c tool includes

Pull x86 fix from Ingo Molnar:
 "Leftover from 4.0

  Fix a local stack variable corruption with certain kdump usage
  patterns (Dave Young)"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/numa: Fix kernel stack corruption in numa_init()->numa_clear_kernel_node_hotplug()

Pull x86 RAS changes from Ingo Molnar:
 "The main changes in this cycle were:

   - Simplify the CMCI storm logic on Intel CPUs after yet another
     report about a race in the code (Borislav Petkov)

   - Enable the MCE threshold irq on AMD CPUs by default (Aravind
     Gopalakrishnan)

   - Add AMD-specific MCE-severity grading function.  Further error
     recovery actions will be based on its output (Aravind Gopalakrishnan)

   - Documentation updates (Borislav Petkov)

   - ... assorted fixes and cleanups"

* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce/severity: Fix warning about indented braces
  x86/mce: Define mce_severity function pointer
  x86/mce: Add an AMD severities-grading function
  x86/mce: Reindent __mcheck_cpu_apply_quirks() properly
  x86/mce: Use safe MSR accesses for AMD quirk
  x86/MCE/AMD: Enable thresholding interrupts by default if supported
  x86/MCE: Make mce_panic() fatal machine check msg in the same pattern
  x86/MCE/intel: Cleanup CMCI storm logic
  Documentation/acpi/einj: Correct and streamline text
  x86/MCE/AMD: Drop bogus const modifier from AMD's bank4_names()

Pull x86 platform change from Ingo Molnar:
 "An Intel Quark SoC fix"

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/intel/quark: Run IMR self-test on IMR capble hw only

Pull x86 mm changes from Ingo Molnar:
 "The main changes in this cycle were:

   - reduce the x86/32 PAE per task PGD allocation overhead from 4K to
     0.032k (Fenghua Yu)

   - early_ioremap/memunmap() usage cleanups (Juergen Gross)

   - gbpages support cleanups (Luis R Rodriguez)

   - improve AMD Bulldozer (family 0x15) ASLR I$ aliasing workaround to
     increase randomization by 3 bits (per bootup) (Hector
     Marco-Gisbert)

   - misc fixlets"

* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Improve AMD Bulldozer ASLR workaround
  x86/mm/pat: Initialize __cachemode2pte_tbl[] and __pte2cachemode_tbl[] in a bit more readable fashion
  init.h: Clean up the __setup()/early_param() macros
  x86/mm: Simplify probe_page_size_mask()
  x86/mm: Further simplify 1 GB kernel linear mappings handling
  x86/mm: Use early_param_on_off() for direct_gbpages
  init.h: Add early_param_on_off()
  x86/mm: Simplify enabling direct_gbpages
  x86/mm: Use IS_ENABLED() for direct_gbpages
  x86/mm: Unexport set_memory_ro() and set_memory_rw()
  x86/mm, efi: Use early_ioremap() in arch/x86/platform/efi/efi-bgrt.c
  x86/mm: Use early_memunmap() instead of early_iounmap()
  x86/mm/pat: Ensure different messages in STRICT_DEVMEM and PAT cases
  x86/mm: Reduce PAE-mode per task pgd allocation overhead from 4K to 32 bytes

Pull x86 microcode changes from Ingo Molnar:
 "Microcode driver updates: mostly cleanups but also some fixes
  (Borislav Petkov)"

* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode/amd: Drop the pci_ids.h dependency
  x86/microcode/intel: Fix printing of microcode blobs in show_saved_mc()
  x86/microcode/intel: Check scan_microcode()'s retval
  x86/microcode/intel: Sanitize microcode_pointer()
  x86/microcode/intel: Move mc arg last in get_matching_{microcode|sig}
  x86/microcode/intel: Simplify generic_load_microcode_early()
  x86/microcode: Consolidate family,model, ... code
  x86/microcode/intel: Rename update_match_revision()
  x86/microcode/intel: Sanitize _save_mc()
  x86/microcode/intel: Make _save_mc() return the updated saved count
  x86/microcode/intel: Simplify load_ucode_intel_bsp()
  x86/microcode/intel: Get rid of last arg to load_ucode_intel_bsp()
  x86/microcode/intel: Do the mc_saved_src NULL check first
  x86/microcode/intel: Check if microcode was found before applying
  x86/microcode/intel: Fix out of bounds memory access to the extended header

Pull x86 fpu changes from Ingo Molnar:
 "Various x86 FPU handling cleanups, refactorings and fixes (Borislav
  Petkov, Oleg Nesterov, Rik van Riel)"

* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
  x86/fpu: Kill eager_fpu_init_bp()
  x86/fpu: Don't allocate fpu->state for swapper/0
  x86/fpu: Rename drop_init_fpu() to fpu_reset_state()
  x86/fpu: Fold __drop_fpu() into its sole user
  x86/fpu: Don't abuse drop_init_fpu() in flush_thread()
  x86/fpu: Use restore_init_xstate() instead of math_state_restore() on kthread exec
  x86/fpu: Introduce restore_init_xstate()
  x86/fpu: Document user_fpu_begin()
  x86/fpu: Factor out memset(xstate, 0) in fpu_finit() paths
  x86/fpu: Change xstateregs_get()/set() to use ->xsave.i387 rather than ->fxsave
  x86/fpu: Don't abuse FPU in kernel threads if use_eager_fpu()
  x86/fpu: Always allow FPU in interrupt if use_eager_fpu()
  x86/fpu: __kernel_fpu_begin() should clear fpu_owner_task even if use_eager_fpu()
  x86/fpu: Also check fpu_lazy_restore() when use_eager_fpu()
  x86/fpu: Use task_disable_lazy_fpu_restore() helper
  x86/fpu: Use an explicit if/else in switch_fpu_prepare()
  x86/fpu: Introduce task_disable_lazy_fpu_restore() helper
  x86/fpu: Move lazy restore functions up a few lines
  x86/fpu: Change math_error() to use unlazy_fpu(), kill (now) unused save_init_fpu()
  x86/fpu: Don't do __thread_fpu_end() if use_eager_fpu()
  ...

Pull x86 debug changes from Ingo Molnar:
 "Stack printing fixlets"

* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kernel: Use kstack_end() in dumpstack_64.c
  x86/kernel: Fix output of show_stack_log_lvl()

Pull x86 cacheinfo sysfs changes from Ingo Molnar:
 "This tree converts the x86 cacheinfo sysfs code to use the generic
  code in drivers/base/cacheinfo.c.

  It's not intended to change the sysfs ABI:

      'This patch neither alters any existing sysfs entries nor their
       formating, however since the generic cacheinfo has switched to
       use the device attributes instead of the traditional raw
       kobjects, a directory named 'power' along with its standard
       attributes are added similar to any other device'"

* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu/cacheinfo: Fix cache_get_priv_group() for Intel processors
  x86/cacheinfo: Move cacheinfo sysfs code to generic infrastructure

Pull x86 cleanups from Ingo Molnar:
 "Various cleanups"

* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/iommu: Fix header comments regarding standard and _FINISH macros
  x86/earlyprintk: Put CONFIG_PCI-only functions under the #ifdef
  x86: Fix up obsolete __cpu_set() function usage

Pull x86 build changes from Ingo Molnar:
 "Small cleanups and fixes"

* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kexec: Cleanup KEXEC_VERIFY_SIG Kconfig help text
  x86/build/defconfig: Enable USB_EHCI_TT_NEWSCHED=y
  x86/build: Fix mkcapflags.sh bash-ism
  x86/Kconfig: Simplify X86_UP_APIC handling
  x86/Kconfig: Simplify X86_IO_APIC dependencies
  x86/Kconfig: Avoid issuing pointless turned off entries to .config

Pull x86 boot changes from Ingo Molnar:
 "A number of cleanups"

* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Standardize strcmp()
  x86/boot/64: Remove pointless early_printk() message
  x86/boot/video: Move the 'video_segment' variable to video.c

Pull x86 asm changes from Ingo Molnar:
 "There were lots of changes in this development cycle:

   - over 100 separate cleanups, restructuring changes, speedups and
     fixes in the x86 system call, irq, trap and other entry code, part
     of a heroic effort to deobfuscate a decade old spaghetti asm code
     and its C code dependencies (Denys Vlasenko, Andy Lutomirski)

   - alternatives code fixes and enhancements (Borislav Petkov)

   - simplifications and cleanups to the compat code (Brian Gerst)

   - signal handling fixes and new x86 testcases (Andy Lutomirski)

   - various other fixes and cleanups

  By their nature many of these changes are risky - we tried to test
  them well on many different x86 systems (there are no known
  regressions), and they are split up finely to help bisection - but
  there's still a fair bit of residual risk left so caveat emptor"

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (148 commits)
  perf/x86/64: Report regs_user->ax too in get_regs_user()
  perf/x86/64: Simplify regs_user->abi setting code in get_regs_user()
  perf/x86/64: Do report user_regs->cx while we are in syscall, in get_regs_user()
  perf/x86/64: Do not guess user_regs->cs, ss, sp in get_regs_user()
  x86/asm/entry/32: Tidy up JNZ instructions after TESTs
  x86/asm/entry/64: Reduce padding in execve stubs
  x86/asm/entry/64: Remove GET_THREAD_INFO() in ret_from_fork
  x86/asm/entry/64: Simplify jumps in ret_from_fork
  x86/asm/entry/64: Remove a redundant jump
  x86/asm/entry/64: Optimize [v]fork/clone stubs
  x86/asm/entry: Zero EXTRA_REGS for stub32_execve() too
  x86/asm/entry/64: Move stub_x32_execvecloser() to stub_execveat()
  x86/asm/entry/64: Use common code for rt_sigreturn() epilogue
  x86/asm/entry/64: Add forgotten CFI annotation
  x86/asm/entry/irq: Simplify interrupt dispatch table (IDT) layout
  x86/asm/entry/64: Move opportunistic sysret code to syscall code path
  x86, selftests: Add sigreturn selftest
  x86/alternatives: Guard NOPs optimization
  x86/asm/entry: Clear EXTRA_REGS for all executable formats
  x86/signal: Remove pax argument from restore_sigcontext
  ...

Pull x86 apic changes from Ingo Molnar:
 "Changes:

   - SGI UV APIC driver updates

   - dead code removal"

* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic/uv: Update the UV APIC HUB check
  x86/apic/uv: Update the UV APIC driver check
  x86/apic/uv: Update the APIC UV OEM check
  x86/apic: Remove verify_local_APIC()

Pull timer updates from Ingo Molnar:
 "The main changes in this cycle were:

   - clockevents state machine cleanups and enhancements (Viresh Kumar)

   - clockevents broadcast notifier horror to state machine conversion
     and related cleanups (Thomas Gleixner, Rafael J Wysocki)

   - clocksource and timekeeping core updates (John Stultz)

   - clocksource driver updates and fixes (Ben Dooks, Dmitry Osipenko,
     Hans de Goede, Laurent Pinchart, Maxime Ripard, Xunlei Pang)

   - y2038 fixes (Xunlei Pang, John Stultz)

   - NMI-safe ktime_get_raw_fast() and general refactoring of the clock
     code, in preparation to perf's per event clock ID support (Peter
     Zijlstra)

   - generic sched/clock fixes, optimizations and cleanups (Daniel
     Thompson)

   - clockevents cpu_down() race fix (Preeti U Murthy)"

* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
  timers/PM: Drop unnecessary braces from tick_freeze()
  timers/PM: Fix up tick_unfreeze()
  timekeeping: Get rid of stale comment
  clockevents: Cleanup dead cpu explicitely
  clockevents: Make tick handover explicit
  clockevents: Remove broadcast oneshot control leftovers
  sched/idle: Use explicit broadcast oneshot control function
  ARM: Tegra: Use explicit broadcast oneshot control function
  ARM: OMAP: Use explicit broadcast oneshot control function
  intel_idle: Use explicit broadcast oneshot control function
  ACPI/idle: Use explicit broadcast control function
  ACPI/PAD: Use explicit broadcast oneshot control function
  x86/amd/idle, clockevents: Use explicit broadcast oneshot control functions
  clockevents: Provide explicit broadcast oneshot control functions
  clockevents: Remove the broadcast control leftovers
  ARM: OMAP: Use explicit broadcast control function
  intel_idle: Use explicit broadcast control function
  cpuidle: Use explicit broadcast control function
  ACPI/processor: Use explicit broadcast control function
  ACPI/PAD: Use explicit broadcast control function
  ...

Pull scheduler changes from Ingo Molnar:
 "Major changes:

   - Reworked CPU capacity code, for better SMP load balancing on
     systems with assymetric CPUs. (Vincent Guittot, Morten Rasmussen)

   - Reworked RT task SMP balancing to be push based instead of pull
     based, to reduce latencies on large CPU count systems. (Steven
     Rostedt)

   - SCHED_DEADLINE support updates and fixes. (Juri Lelli)

   - SCHED_DEADLINE task migration support during CPU hotplug. (Wanpeng Li)

   - x86 mwait-idle optimizations and fixes. (Mike Galbraith, Len Brown)

   - sched/numa improvements. (Rik van Riel)

   - various cleanups"

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
  sched/core: Drop debugging leftover trace_printk call
  sched/deadline: Support DL task migration during CPU hotplug
  sched/core: Check for available DL bandwidth in cpuset_cpu_inactive()
  sched/deadline: Always enqueue on previous rq when dl_task_timer() fires
  sched/core: Remove unused argument from init_[rt|dl]_rq()
  sched/deadline: Fix rt runtime corruption when dl fails its global constraints
  sched/deadline: Avoid a superfluous check
  sched: Improve load balancing in the presence of idle CPUs
  sched: Optimize freq invariant accounting
  sched: Move CFS tasks to CPUs with higher capacity
  sched: Add SD_PREFER_SIBLING for SMT level
  sched: Remove unused struct sched_group_capacity::capacity_orig
  sched: Replace capacity_factor by usage
  sched: Calculate CPU's usage statistic and put it into struct sg_lb_stats::group_usage
  sched: Add struct rq::cpu_capacity_orig
  sched: Make scale_rt invariant with frequency
  sched: Make sched entity usage tracking scale-invariant
  sched: Remove frequency scaling from cpu_capacity
  sched: Track group sched_entity usage contributions
  sched: Add sched_avg::utilization_avg_contrib
  ...

Pull core locking changes from Ingo Molnar:
 "Main changes:

   - jump label asm preparatory work for PowerPC (Anton Blanchard)

   - rwsem optimizations and cleanups (Davidlohr Bueso)

   - mutex optimizations and cleanups (Jason Low)

   - futex fix (Oleg Nesterov)

   - remove broken atomicity checks from {READ,WRITE}_ONCE() (Peter
     Zijlstra)"

* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  powerpc, jump_label: Include linux/jump_label.h to get HAVE_JUMP_LABEL define
  jump_label: Allow jump labels to be used in assembly
  jump_label: Allow asm/jump_label.h to be included in assembly
  locking/mutex: Further simplify mutex_spin_on_owner()
  locking: Remove atomicy checks from {READ,WRITE}_ONCE
  locking/rtmutex: Rename argument in the rt_mutex_adjust_prio_chain() documentation as well
  locking/rwsem: Fix lock optimistic spinning when owner is not running
  locking: Remove ACCESS_ONCE() usage
  locking/rwsem: Check for active lock before bailing on spinning
  locking/rwsem: Avoid deceiving lock spinners
  locking/rwsem: Set lock ownership ASAP
  locking/rwsem: Document barrier need when waking tasks
  locking/futex: Check PF_KTHREAD rather than !p->mm to filter out kthreads
  locking/mutex: Refactor mutex_spin_on_owner()
  locking/mutex: In mutex_spin_on_owner(), return true when owner changes

Pull EFI update from Ingo Molnar:
 "This tree includes various fixes, cleanups, a new efi=debug boot
  option and EFI boot stub memory allocation optimizations"

* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/libstub: Retrieve FDT size when loaded from UEFI config table
  efi: Clean up the efi_call_phys_[prolog|epilog]() save/restore interaction
  efi: Disable interrupts around EFI calls, not in the epilog/prolog calls
  x86/efi: Add a "debug" option to the efi= cmdline
  firmware: dmi_scan: Use direct access to static vars
  firmware: dmi_scan: Use full dmi version for SMBIOS3

Pull md fixes from Neil Brown:
 "Two regression fixes for md, one fairly recent and minor (diskstats
  has confusing data) and one older and more serious - RAID0 with
  non-power-of-2 chunksize corrupts data.

  I guess (almost) no-one uses non-power-of-2 chunks.

  Summary:

   - Revert recent change which broke IO accounting.

   - Fix bug with RAID0 arrays with non-power-of-2 chunk size"

* tag 'md/4.0-rc7-fix' of git://neil.brown.name/md:
  md/raid0: fix bug with chunksize not a power of 2.
  md: fix md io stats accounting broken

Almost all arches define ELF_ET_DYN_BASE as 2/3 of TASK_SIZE.
Though it seems that some architectures do this in a wrong way.
The problem is that 2*TASK_SIZE may overflow 32-bits so
the real ELF_ET_DYN_BASE becomes wrong.
Fix this overflow by dividing TASK_SIZE prior to multiplying:
	 (TASK_SIZE / 3 * 2)
Signed-off-by: NAndrey Ryabinin <a.ryabinin@samsung.com>
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>