- 09 8月, 2010 32 次提交
-
-
由 Andy Walls 提交于
Add initial IR Rx support using the intergrated IR controller in the A/V core of the CX23885 bridge chip. This initial support is flawed in that I2C transactions should not be performed in a hard irq context. That will be fixed in a follow on patch. The TeVii S470 support is reported to generate perptual interrupts that renders a user' system nearly unusable. The TeVii S470 IR will be disabled by default in a follow on patch. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
This patch is primarily a port of the integrated IR controller code in cx23885/cx23888-ir.c. Right now, only the CX2388[57] AV core will really try to set up IR. This IR support, by design, still requires the bridge driver to do final IO pin mux configuration and setup of the IR controller parameters. For the CX2388[578] chips, enabling the AV Core for IR also starts sending Audio and Video interrupts to the bridge driver. For CX2388[578] chips audio and video interrupts are ignored and acknowledged when they happen. IR interrupt handling and status logging is exluded for the CX23888 which does not have an IR controller on the AV core. Note that experimentation reveals that the IR irq enables on the CX23885 have an inverted logic sense. The CX23887 likely suffers from the same quirk. For these chips, those irq enable bits are handled as interrupt disables. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
The CX2584x and related cores are multifunction subdevices with a number of internal blocks that act as interrupt sources. Move the v4L2_subdev interrupt_service_routine callback from v4l_subdev_ir_ops to v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and related cores can generate interrupts along with the IR block. This change also makes sense for other subdev's that generate interrupts and do not have an IR block. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Explicitly configure the IR Tx and IR Rx pins to be driven by the IR Rx and Tx pads from the AV core for CX23888 IR. For the HVR-1850 and HVR-1290 configure the IR Tx level inversion, so the Tx LED is off when idle. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
There is a distinction on IR Tx for the CX2388[578] chips of carrier sense inversion (space is a carrier burst and mark is no burst) and I/O pin level inversion (0 is high output level, 1 is low output level). Allow the caller to set these parameters distinctly as v4l2_subdevice IR parameters. This permits the IR device to be configured and enabled without the IR Tx LED being on during idle/space time due to an external hardware level inversion Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Add s_io_pin_config core subdev op for the CX2388[578] AV cores. This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N. It likely needs work for the I2S signal direction. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Add a method to v4l2_sudev_core_ops to allow bridge drivers to manage what signal pads/functions are routed out to multiplexed IO pins on a pin by pin basis. The interface also allows specifying initial output settings for pins and disabling an IO pin altogether. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Add a simple log_status function for raw analog video capture device nodes, to provide insight into the state of the CX2388[578] A/V decoder core. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
The offset in the eeprom data for the 79501 version of the HVR-1250 is at 0xc0 vs. the standard 0x80. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
There was a small window between writing the cx25840 register address over the i2c bus and reading the register contents back from the cx25840 device that the i2c adapter lock was released. This change ensures the adapter lock is not released until the register read is done. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean Delvare 提交于
Function i2c_wait_done() never returns negative values, so there is no point in checking for them. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean Delvare 提交于
Don't just check for nacks on zero-length transactions. Check on other transactions too. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean Delvare 提交于
Documentation/i2c/fault-codes says that i2c adapter drivers should return -ENXIO when no slave acks an address byte. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
On laptops, the webcam sometimes disconnects when writing the first main register (b300). This patch prevents the creation of a new /dev/video<n> on streaming start. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The added controls are exposure, gain, autogain and backlight compensation. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The JPEG format did not work fine. The Bayer format offers correct VGA (640x480) resolution, but bad QQVGA (160x120). This last resolution is removed. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The bit 7 of the sensor gain register multiplies the 7bits value by two. It is now always set with half the user gain value. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The start_1 exchange must be done by (reg, val) * 5 and not 8. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The sensor enum definition was not at the right place. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: arch/tile: check kmalloc() result arch/tile: catch up on various minor cleanups. arch/tile: avoid erroneous error return for PTRACE_POKEUSR. tile: set ARCH_KMALLOC_MINALIGN tile: remove homegrown L1_CACHE_ALIGN macro arch/tile: Miscellaneous cleanup changes. arch/tile: Split the icache flush code off to a generic <arch> header. arch/tile: Fix bug in support for atomic64_xx() ops. arch/tile: Shrink the tile-opcode files considerably. arch/tile: Add driver to enable access to the user dynamic network. arch/tile: Enable more sophisticated IRQ model for 32-bit chips. Move list types from <linux/list.h> to <linux/types.h>. Add wait4() back to the set of <asm-generic/unistd.h> syscalls. Revert adding some arch-specific signal syscalls to <linux/syscalls.h>. arch/tile: Do not use GFP_KERNEL for dma_alloc_coherent(). Feedback from fujita.tomonori@lab.ntt.co.jp. arch/tile: core support for Tilera 32-bit chips. Fix up the "generic" unistd.h ABI to be more useful.
-
git://www.jni.nu/cris由 Linus Torvalds 提交于
* 'for-linus' of git://www.jni.nu/cris: (51 commits) CRIS: Fix alignment problem for older ld CRIS: Always dump registers for segfaulting process. CRIS: Add config for pausing a seg-faulting process CRIS: Don't take faults while in_atomic CRIS: Fixup lookup for delay slot faults CRIS: Discard exit.text and .data at runtime CRIS: Add cache aligned and read mostly data sections CRIS: Return something from profile write CRIS: Add ARTPEC-3 and timestamps for sync-serial CRIS: Better ARTPEC-3 support for gpio CRIS: Add include guard CRIS: Better handling of pinmux settings CRIS: New DMA defines for ARTPEC-3 CRIS: __do_strncpy_from_user: Don't read the byte beyond the nil CRIS: Pagetable for ARTPEC-3 CRIS: Machine dependent memmap.h CRIS: Check if pointer is set before using it CRIS: Machine dependent dma.h CRIS: Define __read_mostly for CRISv32 CRIS: Discard .note.gnu.build-id section ...
-
git://android.kernel.org/kernel/tegra由 Linus Torvalds 提交于
* 'for-linus' of git://android.kernel.org/kernel/tegra: [ARM] tegra: add MAINTAINERS entry [ARM] tegra: harmony: Add harmony board file [ARM] tegra: add pinmux support [ARM] tegra: add GPIO support [ARM] tegra: Add timer support [ARM] tegra: SMP support [ARM] tegra: Add clock support [ARM] tegra: Add IRQ support [ARM] tegra: initial tegra support
-
git://github.com/schandinat/linux-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://github.com/schandinat/linux-2.6: drivers/video/via/via-gpio.c: fix warning viafb: Depends on X86 fbdev: section cleanup in viafb driver viafb: fix accel_flags check_var bug viafb: probe cleanups viafb: remove ioctls which break the framebuffer interface viafb: update fix before calculating depth viafb: PLL value cleanup viafb: simplify lcd size "detection" viafb: fix PCI table viafb: add lcd scaling support for some IGPs viafb: improve lcd code readability viafb: remove duplicated scaling code MAINTAINERS: update viafb entry
-
git://gitorious.org/linux-omap-dss2/linux由 Linus Torvalds 提交于
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux: (64 commits) OMAP: DSS2: OMAPFB: add support for FBIO_WAITFORVSYNC OMAP: DSS2: Replace strncmp() with sysfs_streq() in overlay_manager_store() OMAP: DSS2: Fix error path in omap_dsi_update() OMAP: DSS2: TDO35S: fix video signaling OMAP: DSS2: OMAPFB: Fix invalid bpp for PAL and NTSC modes OMAP: DSS2: OMAPFB: Fix probe error path OMAP3EVM: Replace vdvi regulator supply with vdds_dsi OMAP: DSS2: Remove extra return statement OMAP: DSS2: adjust YUV overlay width to be even OMAP: DSS2: OMAPFB: Fix sysfs mirror input check OMAP: DSS2: OMAPFB: Remove redundant color register range check OMAP: DSS2: OMAPFB: Remove redundant rotate range check OMAP: DSS2: OMAPFB: Check fb2display() return value OMAP: DSS2: Taal: Optimize enable_te, rotate, mirror when value unchanged OMAP: DSS2: DSI: detect unsupported update requests OMAP: DSS2: DSI: increase FIFO low threshold OMAP: DSS2: DSI: Add error IRQ mask for DSI complexIO OMAP: DSS2: DSI: Remove BTA after set_max_rx_packet_size OMAP: DSS2: change manual update scaling setup OMAP: DSS2: DSI: use BTA to end the frame transfer ...
-
由 Linus Torvalds 提交于
Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (143 commits) omap: mailbox: reorganize headers omap: mailbox: standarize on 'omap-mailbox' omap: mailbox: only compile for configured archs omap: mailbox: simplify omap_mbox_register() omap: mailbox: reorganize registering omap: mailbox: add IRQ names omap: mailbox: remove unecessary fields omap: mailbox: don't export unecessary symbols omap: mailbox: update omap1 probing omap: mailbox: use correct config for omap1 omap: mailbox: 2420 should be detected at run-time omap: mailbox: reorganize structures omap: mailbox: trivial cleanups omap mailbox: Set a device in logical mbox instance for traceability omap: mailbox: convert block api to kfifo omap: mailbox: remove (un)likely macros from cold paths omap: mailbox cleanup: split MODULE_AUTHOR line omap: mailbox: convert rwlocks to spinlock Mailbox: disable mailbox interrupt when request queue Mailbox: new mutext lock for h/w mailbox configuration ...
-
由 Linus Torvalds 提交于
Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci * 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: davinci: dm646x EVM: Specify reserved EDMA channel/slots davinci: da8xx/omapl EVM: Specify reserved channels/slots davinci: support for EDMA resource sharing davinci: edma: provide ability to detect insufficient CC info data davinci: da8xx: sparse cleanup: remove duplicate entries in irq priorities davinci: DM365: fixed second serial port Davinci: tnetv107x evm board initial support Davinci: tnetv107x initial gpio support Davinci: tnetv107x soc support Davinci: tnetv107x decompresser uart definitions Davinci: generalized debug macros
-
- 08 8月, 2010 8 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (82 commits) firewire: core: add forgotten dummy driver methods, remove unused ones firewire: add isochronous multichannel reception firewire: core: small clarifications in core-cdev firewire: core: remove unused code firewire: ohci: release channel in error path firewire: ohci: use memory barriers to order descriptor updates tools/firewire: nosy-dump: increment program version tools/firewire: nosy-dump: remove unused code tools/firewire: nosy-dump: use linux/firewire-constants.h tools/firewire: nosy-dump: break up a deeply nested function tools/firewire: nosy-dump: make some symbols static or const tools/firewire: nosy-dump: change to kernel coding style tools/firewire: nosy-dump: work around segfault in decode_fcp tools/firewire: nosy-dump: fix it on x86-64 tools/firewire: add userspace front-end of nosy firewire: nosy: note ioctls in ioctl-number.txt firewire: nosy: use generic printk macros firewire: nosy: endianess fixes and annotations firewire: nosy: annotate __user pointers and __iomem pointers firewire: nosy: fix device shutdown with active client ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6由 Linus Torvalds 提交于
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (27 commits) ACPI / ACPICA: Simplify acpi_ev_initialize_gpe_block() ACPI / ACPICA: Fail acpi_gpe_wakeup() if ACPI_GPE_CAN_WAKE is unset ACPI / ACPICA: Do not execute _PRW methods during initialization ACPI: Fix bogus GPE test in acpi_bus_set_run_wake_flags() ACPICA: Update version to 20100702 ACPICA: Fix for Alias references within Package objects ACPICA: Fix lint warning for 64-bit constant ACPICA: Remove obsolete GPE function ACPICA: Update debug output components ACPICA: Add support for WDDT - Watchdog Descriptor Table ACPICA: Drop acpi_set_gpe ACPICA: Use low-level GPE enable during GPE block initialization ACPI / EC: Do not use acpi_set_gpe ACPI / EC: Drop suspend and resume routines ACPICA: Remove wakeup GPE reference counting which is not used ACPICA: Introduce acpi_gpe_wakeup() ACPICA: Rename acpi_hw_gpe_register_bit ACPICA: Update version to 20100528 ACPICA: Add signatures for undefined tables: ATKG, GSCI, IEIT ACPICA: Optimization: Reduce the number of namespace walks ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits) IB/qib: Add missing <linux/slab.h> include IB/ehca: Drop unnecessary NULL test RDMA/nes: Fix confusing if statement indentation IB/ehca: Init irq tasklet before irq can happen RDMA/nes: Fix misindented code RDMA/nes: Fix showing wqm_quanta RDMA/nes: Get rid of "set but not used" variables RDMA/nes: Read firmware version from correct place IB/srp: Export req_lim via sysfs IB/srp: Make receive buffer handling more robust IB/srp: Use print_hex_dump() IB: Rename RAW_ETY to RAW_ETHERTYPE RDMA/nes: Fix two sparse warnings RDMA/cxgb3: Make needlessly global iwch_l2t_send() static IB/iser: Make needlessly global iser_alloc_rx_descriptors() static RDMA/cxgb4: Add timeouts when waiting for FW responses IB/qib: Fix race between qib_error_qp() and receive packet processing IB/qib: Limit the number of packets processed per interrupt IB/qib: Allow writes to the diag_counters to be able to clear them IB/qib: Set cfgctxts to number of CPUs by default ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits) ALSA: hda - Add pin-fix for HP dc5750 ALSA: als4000: Fix potentially invalid DMA mode setup ALSA: als4000: enable burst mode ALSA: hda - Fix initial capsrc selection in patch_alc269() ASoC: TWL4030: Capture route runtime DAPM ordering fix ALSA: hda - Add PC-beep whitelist for an Intel board ALSA: hda - More relax for pending period handling ALSA: hda - Define AC_FMT_* constants ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs ALSA: hda - Add support for HDMI HBR passthrough ALSA: hda - Set Stream Type in Stream Format according to AES0 ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF ASoC: wm9081: fix resource reclaim in wm9081_register error path ASoC: wm8978: fix a memory leak if a wm8978_register fail ASoC: wm8974: fix a memory leak if another WM8974 is registered ASoC: wm8961: fix resource reclaim in wm8961_register error path ASoC: wm8955: fix resource reclaim in wm8955_register error path ASoC: wm8940: fix a memory leak if wm8940_register return error ASoC: wm8904: fix resource reclaim in wm8904_register error path ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing由 Linus Torvalds 提交于
* 'bkl/core' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing: do_coredump: Do not take BKL init: Remove the BKL from startup code
-
由 Linus Torvalds 提交于
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: SELINUX: Fix build error.
-
git://linux-nfs.org/~bfields/linux由 Linus Torvalds 提交于
* 'for-2.6.36' of git://linux-nfs.org/~bfields/linux: (34 commits) nfsd4: fix file open accounting for RDWR opens nfsd: don't allow setting maxblksize after svc created nfsd: initialize nfsd versions before creating svc net: sunrpc: removed duplicated #include nfsd41: Fix a crash when a callback is retried nfsd: fix startup/shutdown order bug nfsd: minor nfsd read api cleanup gcc-4.6: nfsd: fix initialized but not read warnings nfsd4: share file descriptors between stateid's nfsd4: fix openmode checking on IO using lock stateid nfsd4: miscellaneous process_open2 cleanup nfsd4: don't pretend to support write delegations nfsd: bypass readahead cache when have struct file nfsd: minor nfsd_svc() cleanup nfsd: move more into nfsd_startup() nfsd: just keep single lockd reference for nfsd nfsd: clean up nfsd_create_serv error handling nfsd: fix error handling in __write_ports_addxprt nfsd: fix error handling when starting nfsd with rpcbind down nfsd4: fix v4 state shutdown error paths ...
-
由 David Howells 提交于
Fix the module init error handling. There are a bunch of goto labels for aborting the init procedure at different points and just undoing what needs undoing - they aren't all in the right places, however. This can lead to an oops like the following: BUG: unable to handle kernel NULL pointer dereference at 0000000000000020 IP: [<ffffffff81042a31>] destroy_workqueue+0x17/0xc0 ... Modules linked in: kafs(+) dns_resolver rxkad af_rxrpc fscache Pid: 2171, comm: insmod Not tainted 2.6.35-cachefs+ #319 DG965RY/ ... Process insmod (pid: 2171, threadinfo ffff88003ca6a000, task ffff88003dcc3050) ... Call Trace: [<ffffffffa0055994>] afs_callback_update_kill+0x10/0x12 [kafs] [<ffffffffa007d1c5>] afs_init+0x190/0x1ce [kafs] [<ffffffffa007d035>] ? afs_init+0x0/0x1ce [kafs] [<ffffffff810001ef>] do_one_initcall+0x59/0x14e [<ffffffff8105f7ee>] sys_init_module+0x9c/0x1de [<ffffffff81001eab>] system_call_fastpath+0x16/0x1b Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-