Mark the OMAP3-specific DPLL functions as being OMAP3-specific by moving
them from mach-omap2/dpll.c to mach-omap2/dpll3xxx.c.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>

Some HW blocks have errata which requires specific slave idle mode
under certain conditions.

This patch adds an hwmod API to allow setting slave idlemode
ensuring that any SYSCONFIG register updates go through hwmod.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

First, this patch adds new worst-case latency values to the
omap_device_pm_latency struct.  Here the worst-case measured latencies
for the activate and deactivate hooks are stored.

In addition, add an option to auto-adjust the latency values used for
device activate/deactivate.

By setting a new 'OMAP_DEVICE_LATENCY_AUTO_ADJUST' flag in the
omap_device_pm_latency struct, the omap_device layer automatically
adjusts the activate/deactivate latencies to the worst-case measured
values.

Anytime a new worst-case value is found, it is printed to the console.
Here is an example log during boot using UART2 s an example.  After
boot, the OPP is manually changed to the 125MHz OPP:

[...]
Freeing init memory: 128K
omap_device: serial8250.2: new worst case deactivate latency 0: 30517
omap_device: serial8250.2: new worst case activate latency 0: 30517
omap_device: serial8250.2: new worst case activate latency 0: 218139648
omap_device: serial8250.2: new worst case deactivate latency 0: 61035
omap_device: serial8250.2: new worst case activate latency 0: 278076171
omap_device: serial8250.2: new worst case activate latency 0: 298614501
omap_device: serial8250.2: new worst case activate latency 0: 327331542

/ # echo 125000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed

omap_device: serial8250.2: new worst case deactivate latency 0: 91552

Motivation: this can be used as a technique to automatically determine
the worst case latency values.  The current method of printing a
warning on every violation is too noisy to actually interact the
console in order to set low OPP to discover latencies.

Another motivation for this patch is that the activate/deactivate
latenices can vary depending on the idlemode of the device.  While
working on the UARTs, I noticed that when using no-idle, the activate
latencies were as high as several hundred msecs as shown above.  When
the UARTs are in smart-idle, the max latency is well under 100 usecs.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This patch only affects documentation; no functional changes are
included.

Clean up comments in the current clockdomain, powerdomain code and
header files.  This mostly involves conversion to kerneldoc format,
although some clarifications are also included.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Nothing calls pwrdm_clk_state_switch(), and the function that seems to be
its ideal use case calls pwrdm_clkdm_state_switch(clk->clkdm), so remove it.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

This patch rearranges the order of structure members in struct powerdomain
to avoid wasting memory due to alignment restrictions.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Replace some bare constants with symbolic constants.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

Add usecounting for wakeup and sleep dependencies.  In the current
situation, if several functions add dependencies on the same
clockdomains, when the first dependency removal function is called,
the dependency will be incorrectly removed from the hardware.

Add clkdm_clear_all_wkdeps() and clkdm_clear_all_sleepdeps(), which
provide a fast and usecounting-consistent way to clear all hardware
clockdomain dependencies, since accesses to these registers can be
quite slow.  pm{2,3}4xx.c has been updated to use these new functions.
The original version of this patch did not touch these files, which
previously wrote directly to the wkdep registers, and thus confused
the usecounting code.  This problem was found by Kevin Hilman
<khilman@deeprootsystems.com>.

N.B.: This patch introduces one significant functional difference over
the previous pm34xx.c code: sleepdeps are now cleared during
clockdomain initialization, whereas previously they were left
untouched.  This has been tested by Kevin and confirmed to work.

The original version of this patch also did not take into
consideration that some clockdomains do not have sleep or wakeup
dependency sources, which caused NULL pointer dereferences.  This
problem was debugged and fixed by Kevin Hilman
<khilman@deeprootsystems.com>.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>

OMAP clockdomains and powerdomains are currently defined statically,
only registered at boot, and never unregistered, so we can remove the
unregister function and the locking.   A variant of this was originally
suggested a while ago by Dmitry Baryshkov <dbaryshkov@gmail.com>.
This version of this patch contains an additional fix from Kevin Hilman
<khilman@deeprootsystems.com> to address one of the pwrdm_for_each_nolock()
users in mach-omap2/pm-debug.c.   Thanks Kevin.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

For some reason, previously, we included the MDM clockdomain on all 24xx,
but the stacked die-on-die modem configuration (chassis mode) is only
available on OMAP2430.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Previously some of the clockdomain wakeup/sleep dependency structures
were shared between several domains.  For the subsequent wakeup and sleep
dependency usecounting patch to work, these can no longer be
shared.  This patch splits the shared structures apart.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Move clockdomain wakeup dependency and sleep dependency data
structures from the powerdomain layer to the clockdomain layer, where
they belong.  These dependencies were originally placed in the
powerdomain layer due to unclear documentation; however, it is clear
now that these dependencies are between clockdomains.  For OMAP2/3,
this is not such a big problem, but for OMAP4 this needs to be fixed.

Thanks to Benoît Cousson <b-cousson@ti.com> for his advice on this
patch.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

One of the clock domains was missing from the auto-generated file.
It has been added here.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The clockdomain related code being in place, it is not necessary to have
some part of the clock code commented out. This would help the validation of
the clockdomain functions using the clock level interfaces.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The armwdt_ck clock uses a fixed divisor, so it can use the OMAP clock
fixed divisor recalculation code, rather than a custom function.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

One of the OMAP1 clocks can use the fixed divisor recalculation code
introduced in the OMAP2 clock code, so rename the
omap2_fixed_divisor_recalc() function to omap_fixed_divisor_recalc()
and make it available to all OMAPs.  A followup patch converts the OMAP1
clock.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

AM3505/17 though a OMAP3530 derivative have the following
main differences

	- Removal of the following OMAP3 modules
		- IVA
		- ISP/CAM
		- Modem and D2D components (MAD2D, SAD2D)
		- USIM
		- SSI
		- Mailboxes
		- USB OTG
		- ICR
		- MSPRO
		- SmartReflex
	- SDRC replaced with EMIF4 Controller in the SDRC subsystem
	  thus adding support for DDR2 memory devices
	- Addition of the following new modules
		- Ethernet MAC (CPGMAC)
		- CAN Controller (HECC)
		- New USB OTG Controller with integrated Phy
		- Video Processing Front End (VPFE)
		- Additional UART (UART4)
	- All security accelerators disabled on GP devices and not to
	  be accessed or configured

This patch defines CPU flags for AM3505/17 and update the clock table.
Clock support for new modules will be added by subsequent patches.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated for 2.6.34 clock layout]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add CK_* flags for the two new Sitara chips, AM3505 and AM3517, and
the OMAP34xx die shrink, OMAP36xx/OMAP37xx.  Introduce a new CK_*
flag, CK_3XXX, that marks all clocks that are common to OMAP3 family
chips.  CK_343X now refers to clocks that are available only on
OMAP34{1,2,3,4}0 (WTBU) and OMAP35{03,15,25,30} (any version).
At some point, the RATE_IN_* flags should be updated also.

While here, add some documentation describing the chip families
covered by these clock flags.

This patch is partially based on patches from Ranjith Lohithakshan
<ranjithl@ti.com> and Vishwanath Sripathy <vishwanath.bs@ti.com>.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Cc: Vishwanath Sripathy <vishwanath.bs@ti.com>

AM3517/05 has a few additional control module registers defined mainly
to control the new IP's. This patch adds support for those new registers.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Port the APIs to support the OMAP4 clockdomain framework.
Also take care of the compiling requirements for the same.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

The introduction of the OMAP4 Clock Domain framework requires
some adaptaions to be done in the earlier files to place the
common and uncommon data in the proper places where they belong.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

The Autogenerated OMAP4 clock domain specific file
(mach-omap2/clockdomains44xx.h) is added here.  This file is
auto-generated using python scripting, and following is the lsit of
the people involved:
Benoit Cousson
Abhijit Pagare
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

Here the APIs are modified to use absolute addresses instead of module offsets.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

Here the ".clkstctrl_reg" field is added to the clockdomain stucture
as the module offsets for OMAP4 do not map one to one for powerdomains
and clockdomains as it used to for OMAP3. Hence we need to use absolute
addresses to access the control registers. Some of the clock domains have
modules falling in the address space of PRM partition. Hence  necessitating
the use of absolute adresses.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

The proper Macros have to be used for platform specific calls and
some of the compiling requirements and init calls are taken care of.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

Taking care of the platform specific and common power domains with
proper checks.  Also refining some Macros according to the latest
OMAP4 requirements.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

The Autogenerated OMAP4 power domain specific file (mach-omap2/powerdomains44xx.h)
is added here.
This file is auto-generated using python scripting and following is the list of the people
involved:
Paul Walmsley
Benoit Cousson
Abhijit Pagare
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>

Module offsets were same for OMAP2 and OMAP3 while they differ for OMAP4.
Hence we need different macros for identifying platform specific offsets.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

Some of the OMAP4 specific chip level initialisations are taken care of.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: updated to use '4430ES1' rather than simply '4430'; updated
 to apply after the intervening cpu.h/id.c patch; thanks also to Tony
 for catching a bug in my rewrite]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

OMAP GP timers keep running for a few cycles after they are stopped,
which can cause the timer to expire and generate an interrupt. The
pending interrupt will prevent e.g. OMAP from entering suspend, thus
we ack it manually.  Only applicable on OMAP2/3/4.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit cfc38999f (backlight: Pass device through notify callback)
added a struct device argument to the notify callback, but didn't
update the user of it in mach-hmt.c
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix following warning when CONFIG_DEBUG_FS wasn't selected:

arch/arm/mach-omap2/pm-debug.c:57: warning: 'pm_dbg_init' declared 'static' but never defined
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Currently, DSS does not wakeup when there is a DMA request.  DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: NSubramani Venkatesh <subramani.venkatesh@windriver.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

During suspend, the kernel timekeeping subsystem is shut down.  Before
suspend and upon resume, it uses a weak function
read_persistent_clock() to determine the amount of time that elapsed
during suspend.

This function was not implemented on OMAP, so from the timekeeping
subsystem perspective (and thus userspace as well) it appeared that no
time elapsed during suspend.

This patch uses the 32k sync timer as a the persistent clock.

NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so
      more than one wrapping of the 32k sync timer during suspend may
      cause problems.  Also note there are not interrupts when the 32k
      sync timer wraps, so something else has to be done.
Reported-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.

Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Acked-by: NNishanth Menon <nm@ti.com>
Reviewed-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

val is an u64 pointer, we need an int to check the error.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.

Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1

This patch fixes the above errors.

Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.
Signed-off-by: NVishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Current value is stored on SDRAM and it is written back during wakeup.
Previously a static value of 0x72 was written there.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Acked-by: NThara Gopinath <thara@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>