This patch adds support for the BM PHY, a new PHY model being used
on ICH9-based implementations.

This new PHY exposes issues in the ICH9 silicon when receiving
jumbo frames large enough to use more than a certain part of the
Rx FIFO, and this unfortunately breaks packet split jumbo receives.
For this reason we re-introduce (for affected adapters only) the
jumbo single-skb receive routine back so that people who do
wish to use jumbo frames on these ich9 platforms can do so.
Part of this problem has to do with CPU sleep states and to make
sure that all the wake up timings are correctly we force them
with the recently merged pm_qos infrastructure written by Mark
Gross. (See http://lkml.org/lkml/2007/10/4/400).

To make code read a bit easier we introduce a _IS_ICH flag so
that we don't need to do mac type checks over the code.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch fixes uli526x driver's issues on a PowerPC boards: uli chip
is unable to receive the packets.

It appears that send_frame_filter prepares the setup frame in the
endianness unsafe manner. On a big endian machines we should shift
the address nibble by two bytes.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The firmware on MPC8610HPCD boards enables ULI ethernet and leaves it
in some funky state before booting Linux. For drivers, it's always good
idea to (re)initialize the hardware prior to requesting interrupts.

This patch fixes the following oops:

Oops: Kernel access of bad area, sig: 11 [#1]
MPC86xx HPCD
NIP: c0172820 LR: c017287c CTR: 00000000
[...]
NIP [c0172820] allocate_rx_buffer+0x2c/0xb0
LR [c017287c] allocate_rx_buffer+0x88/0xb0
Call Trace:
[df82bdc0] [c017287c] allocate_rx_buffer+0x88/0xb0 (unreliable)
[df82bde0] [c0173000] uli526x_interrupt+0xe4/0x49c
[df82be20] [c0045418] request_irq+0xf0/0x114
[df82be50] [c01737b0] uli526x_open+0x48/0x160
[df82be70] [c0201184] dev_open+0xb0/0xe8
[df82be80] [c0200104] dev_change_flags+0x90/0x1bc
[df82bea0] [c035fab0] ip_auto_config+0x214/0xef4
[df82bf60] [c03421c8] kernel_init+0xc4/0x2ac
[df82bff0] [c0010834] kernel_thread+0x44/0x60
Instruction dump:
4e800020 9421ffe0 7c0802a6 bfa10014 7c7e1b78 90010024 80030060 83e30054
2b80002f 419d0078 3fa0c039 48000058 <907f0010> 80630088 2f830000 419e0014
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ucc_geth didn't have anything marked as __iomem.  It was also inconsistent
with its use of in/out accessors (using them sometimes, not using them other
times).  Cleaning this up cuts the warnings down from hundreds to just over a
dozen.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Declared some things static, declared some things in the header.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

During sparse cleanup, found a locking bug.  Some of the sysfs functions were
acquiring a lock, and then returning in the event of an error.  We rearrange
the code so that the lock is released in error conditions, too.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	As part of:

commit c2edacf8
Author: Jay Vosburgh <fubar@us.ibm.com>
Date:   Mon Jul 9 10:42:47 2007 -0700

    bonding / ipv6: no addrconf for slaves separately from master

two steps were rearranged in the enslavement process: netdev_set_master
is now before the call to dev_open to open the slave.

	This patch updates the error cases and unwind process at the
end of bond_enslave to match the new order.  Without this patch, it is
possible for the enslavement to fail, but leave the slave with IFF_SLAVE
set in its flags.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The sysfs layer has an internal protection, that ensures, that
all the process sitting inside ->sore/->show callback exits
before the appropriate entry is unregistered (the calltraces
are rather big, but I can provide them if required).

On the other hand, bonding takes rtnl_lock in
a) the bonding_store_bonds, i.e. in ->store callback,
b) module exit before calling the sysfs unregister routines.

Thus, the classical AB-BA deadlock may occur. To reproduce run
# while :; do modprobe bonding; rmmod bonding; done
and
# while :; do echo '+bond%d' > /sys/class/net/bonding_masters ; done
in parallel.

The fix is to move the bond_destroy_sysfs out of the rtnl_lock,
but _before_ bond_free_all to make sure no bonding devices exist
after module unload.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	Fixed an error unwind in bonding_store_bonds that didn't release
the locks it held, and consolidated unwinds into a common block at the
end of the function.  Bug reported by Pavel Emelyanov <xemul@openvz.org>,
who provided a different fix.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

If the call to bond_create_sysfs_entry in bond_create fails, the
proper rollback is to call unregister_netdevice, not free_netdev.
Otherwise - kernel BUG at net/core/dev.c:4057!

Checked with artificial failures injected into bond_create_sysfs_entry.

Pavel's original patch modified by Jay Vosburgh to move code around
for clarity (remove goto-hopping within the unwind block).
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

reallocation of the policy data was being ignored. It could fail.
Simplify so that there is no need for reallocating.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IWLWIFI should be a tristate so that if IWLCORE and/or IWL3945 are m
and none of them is y kbuild doesn't create an empty 
drivers/net/wireless/built-in.o

This patch also removes the pointless "default n".
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 65e41136.

Unlike the other cases Pavel fixed, this case did not
setup a netdev->destructor of free_netdev, therefore this
change was not correct.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dccp_feat_change() validates length and on error is returning 1.
This happens to work since call chain is checking for 0 == success,
but this is returned to userspace, so make it a real error value.
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

x86.git testing found this build bug on v2.6.26-rc1:

  ERROR: "pnp_get_resource" [drivers/net/irda/smsc-ircc2.ko] undefined!
  make[1]: *** [__modpost] Error 1
  make: *** [modules] Error 2

the driver did not anticipate the case of !CONFIG_PNP which is rare but 
still possible. Instead of restricting the driver to PNP-only in the 
Kconfig space, add the (trivial) dummy struct pnp_driver - this is that 
other drivers use in the !PNP case too.

The driver itself can in theory be initialized on !PNP too in certain 
cases, via smsc_ircc_legacy_probe().

Patch only minimally build tested, i dont have this hardware.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

x86.git testing found the following build failure in latest -git:

 drivers/built-in.o: In function `nsc_ircc_pnp_probe':
 nsc-ircc.c:(.text+0xdf1b6): undefined reference to `pnp_get_resource'
 nsc-ircc.c:(.text+0xdf1d4): undefined reference to `pnp_get_resource'
 nsc-ircc.c:(.text+0xdf1ee): undefined reference to `pnp_get_resource'
 nsc-ircc.c:(.text+0xdf237): undefined reference to `pnp_get_resource'
 nsc-ircc.c:(.text+0xdf24c): undefined reference to `pnp_get_resource'
 drivers/built-in.o:nsc-ircc.c:(.text+0xdf266): more undefined references to `pnp_get_resource' follow
 make: *** [.tmp_vmlinux1] Error 1

triggered via this config:

  http://redhat.com/~mingo/misc/config-Sat_May__3_20_53_13_CEST_2008.bad

while generally most users will have PNP enabled, drivers can support
non-PNP build mode too - and most drivers implement it. That is typically
done by providing a dummy pnp_driver structure that will not probe anything.

The fallback routines in the driver will handle this dumber mode of
operation too.

This patch implements that. I have not tested whether this actually
works on real hardware so take care. It does resolve the build bug.

[ Another solution that is used by a few drivers is to exclude the driver
  in the Kconfig if PNP is disabled, via "depends on PNP", but this would
  limit the availability of the driver needlessly. ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert to netlink helpers by using netlink policy validation.
As a side effect fixes a leak.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are functions to refer to the value of dst->metric[THE_METRIC-1]
directly without use of a inline function "dst_metric" defined in
net/dst.h.

The following patch changes them to use the inline function
consistently.
Signed-off-by: NSatoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSatoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The list_del happens under read-locked devs_lock.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both br2684_push and br2684_exit do so, but unregister_netdev()
releases the device itself.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error path in ieee80211_register_hw() may call the unregister_netdev()
and right after it - the free_netdev(), which is wrong, since the
unregister releases the device itself.

So the proposed fix is to NULL the local->mdev after unregister is done
and check this before calling free_netdev().

I checked - no code uses the local->mdev after unregister in this error
path (but even if some did this would be a BUG).
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This actually had to be merged with the patch #1, but I decided not to
mix two changes in one patch.

There are already two calls to free_netdev() in there, so merge them
into one.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the register_netdevice() call fails the device is leaked,
since the out: label is just rtnl_unlock()+return.

Free the device.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changeset 7f7c4072 ("niu: Determine
the # of ports from the card's VPD data") caused maramba on-board
NIU ports to stop probing properly.

The old code had a fallback that would use a num_ports value of
4 if all the probing methods failed, but that was removed.

This restores the fallback of 4 ports, to get things working
again.

Bump driver version and release date.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise it leaks forever.

Based upon a report by Roland <devzero@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

it removes these warnings when CONFIG_AUDITSYSCALL is unset:

net/xfrm/xfrm_user.c: In function 'xfrm_add_sa':
net/xfrm/xfrm_user.c:412: warning: unused variable 'sid'
net/xfrm/xfrm_user.c:411: warning: unused variable 'sessionid'
net/xfrm/xfrm_user.c:410: warning: unused variable 'loginuid'
net/xfrm/xfrm_user.c: In function 'xfrm_del_sa':
net/xfrm/xfrm_user.c:485: warning: unused variable 'sid'
net/xfrm/xfrm_user.c:484: warning: unused variable 'sessionid'
net/xfrm/xfrm_user.c:483: warning: unused variable 'loginuid'
net/xfrm/xfrm_user.c: In function 'xfrm_add_policy':
net/xfrm/xfrm_user.c:1132: warning: unused variable 'sid'
net/xfrm/xfrm_user.c:1131: warning: unused variable 'sessionid'
net/xfrm/xfrm_user.c:1130: warning: unused variable 'loginuid'
net/xfrm/xfrm_user.c: In function 'xfrm_get_policy':
net/xfrm/xfrm_user.c:1382: warning: unused variable 'sid'
net/xfrm/xfrm_user.c:1381: warning: unused variable 'sessionid'
net/xfrm/xfrm_user.c:1380: warning: unused variable 'loginuid'
net/xfrm/xfrm_user.c: In function 'xfrm_add_pol_expire':
net/xfrm/xfrm_user.c:1620: warning: unused variable 'sid'
net/xfrm/xfrm_user.c:1619: warning: unused variable 'sessionid'
net/xfrm/xfrm_user.c:1618: warning: unused variable 'loginuid'
net/xfrm/xfrm_user.c: In function 'xfrm_add_sa_expire':
net/xfrm/xfrm_user.c:1658: warning: unused variable 'sid'
net/xfrm/xfrm_user.c:1657: warning: unused variable 'sessionid'
net/xfrm/xfrm_user.c:1656: warning: unused variable 'loginuid'
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include/linux/skbuff.h says:
        /* These elements must be at the end, see alloc_skb() for details.  */

net/core/skbuff.c says:
	* See comment in sk_buff definition, just before the 'tail' member

This patch contains my guess as to the actual reason rather than a
dead comment reference loop.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is lack of removing a class from the event queue while changing
from parent to leaf which can cause corruption of this rb tree. This
patch fixes a bug introduced by my patch: "sch_htb: turn intermediate
classes into leaves" commit: 160d5e10.

Many thanks to Jan 'yanek' Bortl for finding a way to reproduce this
rare bug and narrowing the test case, which made possible proper
diagnosing.

This patch is recommended for all kernels starting from 2.6.20.
Reported-and-tested-by: NJan 'yanek' Bortl <yanek@ya.bofh.cz>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rose_node_start() as well as in rose_node_stop() __acquires() and
spin_lock_bh() were wrongly passing rose_neigh_list_lock instead of
rose_node_list_lock arguments.
Signed-off-by: NBernard Pidoux <f6bvp@amsat.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This trivial fix retrieves the network namespace from frag queue
and use it to get the network device in the right namespace.
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a netdev is moved across namespaces with the
'dev_change_net_namespace' function, the 'device_rename' function is
used to fixup kobject and refresh the sysfs tree. The device_rename
function will call kobject_rename and this one will check if there is
an object with the same name and this is the case because we are
renaming the object with the same name.

The use of 'device_rename' seems for me wrong because we usually don't
rename it but just move it across namespaces. As we just want to do a
mini "netdev_[un]register", IMO the functions
'netdev_[un]register_kobject' should be used instead, like an usual
network device [un]registering.

This patch replace device_rename by netdev_unregister_kobject,
followed by netdev_register_kobject.

The netdev_register_kobject will call device_initialize and will raise
a warning indicating the device was already initialized. In order to
fix that, I split the device initialization into a separate function
and use it together with 'netdev_register_kobject' into
register_netdevice. So we can safely call 'netdev_register_kobject' in
'dev_change_net_namespace'.

This fix will allow to properly use the sysfs per namespace which is
coming from -mm tree.
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: NBenjamin Thery <benjamin.thery@bull.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new RV2P firmware fixes 2 issues:

1. The jumbo rx buffer page size is now configurable and set to the
   proper PAGE_SIZE.  Before, it was assumed to be always 4K.

2. Driver sometimes would crash when receiving jumbo packets mixed
   with firmware management packets.  This was caused by the old
   firmware DMA'ing to the wrong address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should zero out the context memory for 5709 before each reset.  When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some remote PHY blade systems, the driver receives no initial link
interrupt.  As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.

With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls.  This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The forwarding table binary interface (my bad choice), only exposes
the port number of the first 8 bits. The bridge code was limited to
256 ports at the time, but now the kernel supports up 1024 ports, so
the upper bits are lost when doing:

   brctl showmacs

The fix is to squeeze the extra bits into small hole left in data
structure, to maintain binary compatiablity.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the version number to 3.92.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>