Testing with DIM enabled on older kernels indicated that firmware calls
were slower than expected.  More detailed analysis indicated that the
default 25us delay was higher than necessary.  Reducing the time spend in
usleep_range() for the first several calls would reduce the overall
latency of firmware calls on newer Intel processors.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This keeps the RING_IDLE flag set in hardware for higher coalesce
settings by default and improved latency.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware does not allow the operation and would return failure, causing
a warning in dmesg.  So check for VF and disallow it in the driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add counters to display sum of rx/tx_discard_pkts of all rings as
function level statistics via ethtool.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace switch statements printing different messages for every ring type
with a common message.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older firmware will reject this call and cause an error message to
be printed by the VF driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware messages that are forwarded from PF to VFs are encapsulated.
The size of these encapsulated messages must not exceed the maximum
defined message size.  Add appropriate checks to avoid oversize
messages.  Firmware messages may be expanded in future specs and
this will provide some guardrails to avoid data corruption.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initially, the MQPRIO TCs are mapped 1:1 directly to the hardware
queues.  Some of these hardware queues are configured to be lossless.
When PFC is enabled on one of more TCs, we now need to remap the
TCs that have PFC enabled to the lossless hardware queues.

After remapping, we need to close and open the NIC for the new
mapping to take effect.  We also need to reprogram all ETS parameters.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current driver maps MQPRIO traffic classes directly 1:1 to the
internal hardware queues (TC0 maps to hardware queue 0, etc).  This
direct mapping requires the internal hardware queues to be reconfigured
from lossless to lossy and vice versa when necessary.  This
involves reconfiguring internal buffer thresholds which is
disruptive and not always reliable.

Implement a new scheme to map TCs to internal hardware queues by
matching up their PFC requirements.  This will eliminate the need
to reconfigure a hardware queue internal buffers at run time.  After
remapping, the NIC is closed and opened for the new TC to hardware
queues to take effect.

This patch only adds the basic mapping logic.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support ndo_get_stats64 instead of ndo_get_stats.  Also add stats for
multicast and broadcast packets.
Signed-off-by: NPradeep Nalla <pradeep.nalla@cavium.com>
Acked-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support the next patch in this series which has code that calls
octnet_get_link_stats from two different .c files, move that function (and
its dependency octnet_nic_stats_callback) to lio_core.c.  Remove
octnet_get_link_stats's static declaration and add its function prototype
in octeon_network.h.
Signed-off-by: NPradeep Nalla <pradeep.nalla@cavium.com>
Acked-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two identical nested if statements, the second is redundant
and can be removed. Also clean up white space formatting.

Cleans up cppcheck warning:
drivers/net/ethernet/amd/amd8111e.c:1080: (warning) Identical inner 'if'
condition is always true.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows filters added by tc-flower and specifying MAC addresses,
Ethernet types, and the VLAN priority field, to be offloaded to the
controller.

This reuses most of the infrastructure used by ethtool, but clsflower
filters are kept in a separated list, so they are invisible to
ethtool.

To setup clsflower offloading:

$ tc qdisc replace dev eth0 handle 100: parent root mqprio \
     	   	   num_tc 3 map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
		   queues 1@0 1@1 2@2 hw 0
(clsflower offloading depends on the netword driver to be configured
with multiple traffic classes, we use mqprio's 'num_tc' parameter to
set it to 3)

$ tc qdisc add dev eth0 ingress

Examples of filters:

$ tc filter add dev eth0 parent ffff: flower \
     	    dst_mac aa:aa:aa:aa:aa:aa \
	    hw_tc 2 skip_sw
(just a simple filter filtering for the destination MAC address and
steering that traffic to queue 2)

$ tc filter add dev enp2s0 parent ffff: proto 0x22f0 flower \
     	    src_mac cc:cc:cc:cc:cc:cc \
	    hw_tc 1 skip_sw
(as the i210 doesn't support steering traffic based on the source
address alone, we need to use another steering traffic, in this case
we are using the ethernet type (0x22f0) to steer traffic to queue 1)
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a flower rule has a repr both as ingress and egress port then 2
callbacks may be generated for the same rule request.

Add an indicator to each flow as to whether or not it was added from an
ingress registered cb. If so then ignore add/del/stat requests to it from
an egress cb.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When multiple netdevs are attached to a tc offload block and register for
callbacks, a rule added to the block will be propogated to all netdevs.
Previously these were detected as duplicates (based on cookie) and
rejected. Modify the rule nfp lookup function to optionally include an
ingress netdev and a host context along with the cookie value when
searching for a rule. When a new rule is passed to the driver, the netdev
the rule is to be attached to is considered when searching for dublicates.
When a stats update is received from HW, the host context is used
alongside the cookie to map to the correct host rule.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To aid debugging of performance issues caused by limited PCIe
bandwidth print the PCIe link information on probe.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP locks record the owner when held, for PCIe devices the owner
ID will be the PCIe link number.  When driver loads it should scan
known locks and if they indicate that they are held by local
endpoint but the driver doesn't hold them - release them.

Locks can be left taken for instance when kernel gets kexec-ed or
after a crash.  Management FW tries to clean up stale locks too,
but it currently depends on PCIe link going down which doesn't
always happen.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds basic functions needed to implement offloading for filters
created by tc-flower.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds the capability of configuring the queue steering of arriving
packets based on their source and destination MAC addresses.

Source address steering (i.e. driving traffic to a specific queue),
for the i210, does not work, but filtering does (i.e. accepting
traffic based on the source address). So, trying to add a filter
specifying only a source address will be an error.

In practical terms this adds support for the following use cases,
characterized by these examples:

$ ethtool -N eth0 flow-type ether dst aa:aa:aa:aa:aa:aa action 0
(this will direct packets with destination address "aa:aa:aa:aa:aa:aa"
to the RX queue 0)

$ ethtool -N eth0 flow-type ether src 44:44:44:44:44:44 \
  	     	  	    	  proto 0x22f0 action 3
(this will direct packets with source address "44:44:44:44:44:44" and
ethertype 0x22f0 to the RX queue 3)
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows igb_add_filter()/igb_erase_filter() to work on filters
that include MAC addresses (both source and destination).

For now, this only exposes the functionality, the next commit glues
ethtool into this. Later in this series, these APIs are used to allow
offloading of cls_flower filters.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Users expect that when adding a steering filter for the local MAC
address, that all the traffic directed to that address will go to some
queue.

Currently, it's not possible to configure entries in the "in use"
state, which is the normal state of the local MAC address entry (it is
the default), this patch allows to override the steering configuration
of "in use" entries, if the filter to be added match the address and
address type (source or destination) of an existing entry.

There is a bit of a special handling for entries referring to the
local MAC address, when they are removed, only the steering
configuration is reset.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On some igb models (82575 and i210) the MAC address filters can
control to which queue the packet will be assigned.

This extends the 'state' with one more state to signify that queue
selection should be enabled for that filter.

As 82575 parts are no longer easily obtained (and this was developed
against i210), only support for the i210 model is enabled.

These functions are exported and will be used in the next patch.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Makes it possible to direct packets to queues based on their source
address. Documents the expected usage of the 'flags' parameter.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This will allow functionality depending on the hardware being traffic
class aware to work. In particular the tc-flower offloading checks
verifies that this bit is set.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On the RAH registers there are semantic differences on the meaning of
the "queue" parameter for traffic steering depending on the controller
model: there is the 82575 meaning, which "queue" means a RX Hardware
Queue, and the i350 meaning, where it is a reception pool.

The previous behaviour was having no effect for i210 based controllers
because the QSEL bit of the RAH register wasn't being set.

This patch separates the condition in discrete cases, so the different
handling is clearer.

Fixes: 83c21335 ("igb: improve MAC filter handling")
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Because the order of the parameters passes to 'hlist_add_behind()' was
inverted, the 'parent' node was added "behind" the 'input', as input
is not in the list, this causes the 'input' node to be lost.

Fixes: 0e71def2 ("igb: add support of RX network flow classification")
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original implementation for macvlan offload has us performing a full
port reset every time we added a new macvlan. This shouldn't be necessary
and can be avoided with a few behavior changes.

This patches updates the logic for the queues so that we have essentially 3
possible configurations for macvlan offload. They consist of 15 macvlans
with 4 queues per macvlan, 31 macvlans with 2 queues per macvlan, and 63
macvlans with 1 queue per macvlan. As macvlans are added you will encounter
up to 3 total resets if you add all the way up to 63, and after that the
device will stay in the mode supporting up to 63 macvlans until the L2FW
flag is cleared.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch drops the real_adapter member from the fwd_adapter structure.
The general idea behind the change is that the real_adapter is carrying
unnecessary data since we could always just grab the adapter structure
from netdev_priv(macvlan->lowerdev) if we really needed to get at it.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Both the ixgbe and fm10k drivers support destination filtering.

Instead of adding a ton of complexity to support either source or passthru
mode we can instead just avoid offloading them for now. Doing this we avoid
leaking packets into interfaces that aren't meant to receive them.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Drop dead code now that we shouldn't be receiving broadcast or multicast
frames on the queues associated to the macvlan netdev.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we use a software path for packets that are
going to be locally switched between two macvlan interfaces on the same
device. In addition we resort to software replication of broadcast and
multicast packets instead of offloading that to hardware.

The general idea is that using the device for east/west traffic local to
the system is extremely inefficient. We can only support up to whatever the
PCIe limit is for any given device so this caps us at somewhere around 20G
for devices supported by ixgbe. This is compounded even further when you
take broadcast and multicast into account as a single 10G port can come to
a crawl as a packet is replicated up to 60+ times in some cases. In order
to get away from that I am implementing changes so that we handle
broadcast/multicast replication and east/west local traffic all in
software.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change renames the fwd_priv member to accel_priv as this more
accurately reflects the actual purpose of this value. In addition I am
adding an accessor which will allow us to further abstract this in the
future if needed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Drop the code for handling macvlan specific unicast lists. It isn't needed
since we don't take any efforts to maintain it when we bring the interface
up and it takes the slow path anyway.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Comparison instruction requires a subtraction.  If the constant
is negative we are more likely to fit it into a NFP instruction
directly if we change the sign and use addition.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

There are quite a few compare instructions now, use a table
to translate BPF instruction code to NFP instruction parameters
instead of parameterizing helpers.  This saves LOC and makes
future extensions easier.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

NFP instruction set can fit small immediates into the instruction.
Negative integers, however, will never fit because they will have
highest bit set.  If we swap the ALU op between ADD and SUB and
negate the constant we have a better chance of fitting small negative
integers into the instruction itself and saving one or two cycles.

immed[gprB_21, 0xfffffffc]
alu[gprA_4, gprA_4, +, gprB_21], gpr_wrboth
immed[gprB_21, 0xffffffff]
alu[gprA_5, gprA_5, +carry, gprB_21], gpr_wrboth

now becomes:

alu[gprA_4, gprA_4, -, 4], gpr_wrboth
alu[gprA_5, gprA_5, -carry, 0], gpr_wrboth
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Whitespace cleanup - remove double space.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Swap VF representor tx and rx interface statistics since it is a
virtual switchdev port and tx for VM should be rx for VF representor
and vice-versa.
Signed-off-by: NSrinivas Jampala <srinivasa.jampala@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check port->rev_info.major >= 6 is being performed twice, thus
the inner second check is always true and is redundant, hence it
can be removed. Detected by cppcheck.

drivers/net/ethernet/freescale/fman/fman_port.c:1394]: (warning)
Identical inner 'if' condition is always true.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>