Add two events that were defined in the device specification but were
not exposed in the driver list.

Post this patch those events can be read over the DEVX events interface
once be reported by the firmware.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Reviewed-by: NEdward Srouji <edwards@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190808084358.29517-4-leon@kernel.orgSigned-off-by: NDoug Ledford <dledford@redhat.com>

Merging tip of mlx5-next in order to get changes related to adding
XRQ support to the DEVX interface needed prior to the following two
patches.
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add XRQ legacy commands opcodes, will be used via the DEVX interface.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

As QP may be created by DEVX, it may be valid to not find the rsn in
mlx5 core tree, change the level to be debug.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

Here uses the new APIs instead of some dev print interfaces in
some functions.
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-15-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

If we enabled alw_lcl_lpbk in promiscuous mode, packet whose source
and destination mac address is equal will be handled in both inner
loopback and outer loopback. This will halve performance of roce in
promiscuous mode.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Link: https://lore.kernel.org/r/1565276034-97329-14-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

There is no need to tell users when eq->cons_index is overflow, we
just set it back to zero.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Link: https://lore.kernel.org/r/1565276034-97329-13-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

In order to reduce the complexity of hns_roce_v2_set_hem, extract
the implementation of op as a function.
Signed-off-by: NYangyang Li <liyangyang20@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-12-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

For hns_roce_v2_query_qp and hns_roce_v2_modify_qp,
we can use stack memory to create qp context data.
Make the code simpler.
Signed-off-by: NLang Cheng <chenglang@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-11-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Remove unnecessary if...else..., to make the code look simpler.
Signed-off-by: NLang Cheng <chenglang@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-10-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Assign statement can not be contained in bool statement or
function param.
Signed-off-by: NLang Cheng <chenglang@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-9-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Handling the error return value of hns_roce_calc_hem_mhop.
Signed-off-by: NLang Cheng <chenglang@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-8-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Here removes some useless comments and adds necessary spaces to
another comments.
Signed-off-by: NLang Cheng <chenglang@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-7-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Here remove some unncessary initialization for some valiables.
Signed-off-by: NLang Cheng <chenglang@huawei.com>
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-6-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

There is no need to init the enable bit of cmq.
Signed-off-by: NYixian Liu <liuyixian@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-5-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Current prompt message is uncorrect when destroying qp, add qpn
information when creating qp.
Signed-off-by: NYixian Liu <liuyixian@huawei.com>
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-4-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Here mainly packages some code into some new functions in order to
reduce code compelexity.
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-3-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

It needs to check the sq size with integrity when configures
the relatived parameters of sq. Here moves the relatived code
into a special function.
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Link: https://lore.kernel.org/r/1565276034-97329-2-git-send-email-oulijun@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Since commit a07fc0bb ("RDMA/hns: Fix build error")
these kconfig comment is obsolete, so just remove it.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190807032228.6788-1-yuehaibing@huawei.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Now that we have a common iWARP query port function we can remove the
common code from the iWARP drivers.
Signed-off-by: NKamal Heib <kamalheib1@gmail.com>
Acked-by: NPotnuri Bharat Teja <bharat@chelsio.com>
Link: https://lore.kernel.org/r/20190807103138.17219-5-kamalheib1@gmail.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Add support for a common iWARP query port function, the new function
includes a common code that is used by the iWARP devices to update the
port attributes like max_mtu, active_mtu, state, and phys_state, the
function also includes a call for the driver-specific query_port callback
to query the device-specific port attributes.
Signed-off-by: NKamal Heib <kamalheib1@gmail.com>
Link: https://lore.kernel.org/r/20190807103138.17219-4-kamalheib1@gmail.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

This change is required to associate the cxgb3 ib_dev with the
underlying net_device, so in the upcoming patch we can call
ib_device_get_netdev().
Signed-off-by: NKamal Heib <kamalheib1@gmail.com>
Link: https://lore.kernel.org/r/20190807103138.17219-3-kamalheib1@gmail.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

In order to improve readability, add ib_port_phys_state enum to replace
the use of magic numbers.
Signed-off-by: NKamal Heib <kamalheib1@gmail.com>
Reviewed-by: NAndrew Boyer <aboyer@tobark.org>
Acked-by: NMichal Kalderon <michal.kalderon@marvell.com>
Acked-by: NBernard Metzler <bmt@zurich.ibm.com>
Link: https://lore.kernel.org/r/20190807103138.17219-2-kamalheib1@gmail.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Reference counters are preferred to use refcount_t instead of
atomic_t.
This is because the implementation of refcount_t can prevent
overflows and detect possible use-after-free.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

There is a self assignment of esw->dev to itself, clean this up by
removing it. Also make dev a const pointer.

Addresses-Coverity: ("Self assignment")
Fixes: 6cedde45 ("net/mlx5: E-Switch, Verify support QoS element type")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Admin queue error prints should never happen unless something wrong
happened to the device. However, in the unfortunate case that it does,
we should take extra care not to flood the log with error messages.
Reviewed-by: NFiras JahJah <firasj@amazon.com>
Reviewed-by: NYossi Leybovich <sleybo@amazon.com>
Signed-off-by: NGal Pressman <galpress@amazon.com>
Link: https://lore.kernel.org/r/20190801171447.54440-3-galpress@amazon.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Add ratelimited helpers to the ibdev_* printk functions.
Implementation inspired by counterpart dev_*_ratelimited functions.
Signed-off-by: NGal Pressman <galpress@amazon.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190801171447.54440-2-galpress@amazon.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

UAR in CQ is not used and generates the following compilation
warning, clean the code by removing uar assignment.

drivers/infiniband/hw/hns/hns_roce_cq.c: In function _create_user_cq_:
drivers/infiniband/hw/hns/hns_roce_cq.c:305:27: warning: parameter _uar_ set but not used [-Wunused-but-set-parameter]
  305 |      struct hns_roce_uar *uar,
      |      ~~~~~~~~~~~~~~~~~~~~~^~~

Fixes: 4f8f0d5e ("RDMA/hns: Package the flow of creating cq")
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190801114827.24263-1-leon@kernel.orgSigned-off-by: NDoug Ledford <dledford@redhat.com>

Send and Receive completion is handled on a single CPU selected at
the time each Completion Queue is allocated. Typically this is when
an initiator instantiates an RDMA transport, or when a target
accepts an RDMA connection.

Some ULPs cannot open a connection per CPU to spread completion
workload across available CPUs and MSI vectors. For such ULPs,
provide an API that allows the RDMA core to select a completion
vector based on the device's complement of available comp_vecs.

ULPs that invoke ib_alloc_cq() with only comp_vector 0 are converted
to use the new API so that their completion workloads interfere less
with each other.
Suggested-by: NHåkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Cc: <linux-cifs@vger.kernel.org>
Cc: <v9fs-developer@lists.sourceforge.net>
Link: https://lore.kernel.org/r/20190729171923.13428.52555.stgit@manet.1015granger.netSigned-off-by: NDoug Ledford <dledford@redhat.com>

The "MLX5_CMD_OP_QUERY_LAG" is one of the DEVX general commands, add it.

Fixes: 8aa8c95c ("IB/mlx5: Add support for DEVX general command")
Signed-off-by: NMark Zhang <markz@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

Remove the "reserved_at_40" field to match the device specification.

Fixes: 84df61eb ("net/mlx5: Add HW interfaces used by LAG")
Signed-off-by: NMark Zhang <markz@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

The line continuations unintentionally add whitespace so
instead use coalesced formats to remove the whitespace.
Signed-off-by: NJoe Perches <joe@perches.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/f14db3287b23ed8af9bdbf8001e2e2fe7ae9e43a.camel@perches.comSigned-off-by: NDoug Ledford <dledford@redhat.com>

Currently for PF and ECPF vports, representors are created before
their eswitch hardware ports are initialized in below flow.

mlx5_eswitch_enable()
  esw_offloads_init()
    esw_offloads_load_all_reps()
[..]
esw_enable_vport()

However for VFs, vports are initialized before creating their
respective netdev represnetors in event handling context.

Similarly while disabling eswitch, first hardware vports are disabled,
followed by destroying their representors.
Here while underlying vports gets destroyed but its respective user
facing netdevice can still exist on which user can continue to perform
more offload operations.

Instead, its more accurate to do
enable_eswitch switchdev mode:
1. perform FDB tables initialization
2. initialize hw vport
3. create and publish representor for this vport

disable_eswitch switchdev mode:
1. destroy user facing representor for the vport
2. disable hw vport
3. perform FDB tables cleanup
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

mc_promisc pointer points to an instance of struct esw_mc_addr allocated
as part of the esw structure.
Hence it cannot be NULL.
Removed such redundant check and assign where it is actually used.

While at it, add comment around legacy mode fields and move mc_promisc
close to other legacy mode structures to improve code redability.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

We don't need to handle error flow of esw_create_legacy_table() in the
same branch, it is already being handled directly after the if statement,
for both legacy and switchdev modes in one place.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

vports needs to be enabled in switchdev and legacy mode.

In switchdev mode, vports should be enabled after initializing
the FDB tables and before creating their represntors so that
representor works on an initialized vport object.

Prepare a helper function which can be called when enabling either of
the eswitch modes.

Similarly, have disable vports helper function.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

First enable TSAR Qos hardware block in device before enabling its
user vports.

This refactor is needed so that vports can be enabled before their
representor netdevice can be created.

While at it, esw_create_tsar() returns error code which was used only to
print error. However esw_create_tsar() already prints warning if it hits
an error.
Hence, remove the redundant warning.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Except bit toggling code, rest of the code is same to enable/disable
metadata passing functionality.
Hence, combine them to single function and control using enable flag.

Also instead of checking metadata supported at multiple places,
fold into the helper function.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Check if firmware supports the requested element type before
attempting to create the element type.
In addition, explicitly specify the request element type and tsar type.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently mlx5_load_one() perform device registration using
mlx5_register_device(). But mlx5_unload_one() doesn't unregister.

Make them symmetric by doing device unregistration in
mlx5_unload_one().
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>