We usually assume that increasing PCI device revision ID's translates to
newer steppings; macros like IS_KBL_REVID() that we use rely on this
behavior.  Unfortunately this turns out to not be true on KBL; the
newer device 2 revision ID's sometimes go backward to older steppings.
The situation is further complicated by different GT and display
steppings associated with each revision ID.

Let's work around this by providing a table to map the revision ID to
specific GT and display steppings, and then perform our comparisons on
the mapped values.

v2:
 - Move the kbl_revids[] array to intel_workarounds.c to avoid compiler
   warnings about an unused variable in files that don't call the
   macros (kernel test robot).

Bspec: 18329
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200811032105.2819370-1-matthew.d.roper@intel.comReviewed-by: NSwathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This new HBR2 table for TGL-U and TGL-Y is required to pass
DisplayPort compliance.

BSpec: 49291
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-2-jose.souza@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

There is no way to differentiate TGL-U from TGL-Y by the PCI ids as
some ids are available in both SKUs.
So here using the root device id in the PCI bus that iGPU is in
to differentiate between U and Y.

BSpec: 44455
Reviewed-by: NSwathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-1-jose.souza@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

The command register is the PCODE MBOX low register not the high one as
described by the spec. This left the system with the TC-cold power state
being blocked all the time. Fix things by using the correct register.

Also to make sure we retry a request for at least 600usec, when the
PCODE MBOX command itself succeeded, but the TC-cold block command
failed, sleep for 1msec unconditionally after any fail.

The change was tested with JTAG register read of the HW/FW's actual
TC-cold state, which reported the expected states after this change.
Tested-by: NNivedita Swaminathan <nivedita.swaminathan@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805150056.24248-1-imre.deak@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

The dependency between power wells is determined by the ordering of the
power well list: when enabling the power wells for a domain, this
happens walking the power well list forward, while disabling them
happens in the reverse direction. Accordingly a power well on the list
must follow any other power well it depends on.

Since the TC AUX power wells depend on TC-cold being blocked, move the
TC-cold off power well before all AUX power wells.

Fixes: 3c02934b ("drm/i915/tc/tgl: Implement TC cold sequences")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720232952.16228-1-imre.deak@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

igt_mm_config() calls ilog2() on the (pseudo)random 21-bit number
s>>12.  Once in 2 million seeds, this is zero and ilog2 summons
the nasal demons.

There was an attempt to handle this case with a max(), but that's
too late; ms could already be something bizarre.

Given that the low 12 bits of s and ms are always zero, it's a lot
simpler just to divide them by 4096, then everything fits into 32
bits, and we can easily generate a random number 1 <= s <= 0x1fffff.

Fixes: 14d1b9a6 ("drm/i915: buddy allocator")
Signed-off-by: NGeorge Spelvin <lkml@sdf.org>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325192429.GA8865@SDF.ORGSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Introduces a new parameters to execbuf so that we can specify syncobj
handles as well as timeline points.

v2: Reuse i915_user_extension_fn

v3: Check that the chained extension is only present once (Chris)

v4: Check that dma_fence_chain_find_seqno returns a non NULL fence (Lionel)

v5: Use BIT_ULL (Chris)

v6: Fix issue with already signaled timeline points,
    dma_fence_chain_find_seqno() setting fence to NULL (Chris)

v7: Report ENOENT with invalid syncobj handle (Lionel)

v8: Check for out of order timeline point insertion (Chris)

v9: After explanations on
    https://lists.freedesktop.org/archives/dri-devel/2019-August/229287.html
    drop the ordering check from v8 (Lionel)

v10: Set first extension enum item to 1 (Jason)

v11: Rebase

v12: Allow multiple extension nodes of timeline syncobj (Chris)
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Co-authored-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v11)
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200804085954.350343-3-lionel.g.landwerlin@intel.com
Link: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/2901Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

We're planning to use this for a couple of new feature where we need
to provide additional parameters to execbuf.

v2: Check for invalid flags in execbuffer2 (Lionel)

v3: Rename I915_EXEC_EXT -> I915_EXEC_USE_EXTENSIONS (Chris)

v4: Rebase
    Move array fence parsing in i915_gem_do_execbuffer()
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200804085954.350343-2-lionel.g.landwerlin@intel.com
Link: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/2901Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

The hardware team has dropped this workaround from the bspec; it is no
longer needed.

This reverts commit 111822b21be995a3a4a731066db3d820523c57f7.

Bspec: 49291
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200804044024.1931170-1-matthew.d.roper@intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

In the case of calling check_digital_port_conflicts() failed, a
negative error code -EINVAL should be returned.

Fixes: bf5da83e ("drm/i915: Move check_digital_port_conflicts() earier")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NTianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200802111535.5200-1-tianjia.zhang@linux.alibaba.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

In function i915_active_acquire_preallocate_barrier(), not all
paths have the return value set correctly, and in case of memory
allocation failure, a negative error code should be returned.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NTianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200802115655.25568-1-chris@chris-wilson.co.ukSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

A recent bspec update removed the LPDDR4 single channel entry from the
buddy register table, but added a new four-channel entry.

Workaround 1409767108 hasn't been updated with any guidance for four
channel configurations, so we leave that alternate table unchanged for
now.

Bspec 49218
Fixes: 3fa01d64 ("drm/i915/tgl: Program BW_BUDDY registers during display init")
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612204734.3674650-1-matthew.d.roper@intel.comReviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

We use i915_active_fini() as a debug check on the i915_active state
before freeing. If we forget to call it, we may end up angering the
debugobjects contained within.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NThomas Hellström <thomas.hellstrom@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200731085015.32368-1-chris@chris-wilson.co.ukSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Avoid a GPF at

<1>[   20.177320] BUG: kernel NULL pointer dereference, address: 000000000000007c
<1>[   20.177322] #PF: supervisor read access in kernel mode
<1>[   20.177323] #PF: error_code(0x0000) - not-present page
<6>[   20.177324] PGD 0 P4D 0
<4>[   20.177327] Oops: 0000 [#1] PREEMPT SMP PTI
<4>[   20.177328] CPU: 1 PID: 944 Comm: debugfs_test Not tainted 5.8.0-rc7-CI-CI_DRM_8814+ #1
<4>[   20.177330] Hardware name: Dell Inc. XPS 13 9360/0823VW, BIOS 2.9.0 07/09/2018
<4>[   20.177372] RIP: 0010:i915_lpsp_capability_show+0x44/0xc0 [i915]
<4>[   20.177374] Code: 0f b6 81 ca 0d 00 00 3c 0b 74 77 76 19 3c 0c 75 44 83 7e 7c 01 7e 2f 48 c7 c6 d7 b9 47 a0 e8 43 df 06 e1 31 c0 c3 3c 09 72 2b <8b> 46 7c 85 c0 75 e6 8b 82 e4 00 00 00 89 c2 83 e2 fb 83 fa 0a 74
<4>[   20.177376] RSP: 0018:ffffc90000cebe38 EFLAGS: 00010246
<4>[   20.177377] RAX: 0000000000000009 RBX: ffff888267fe6a58 RCX: ffff888252d10000
<4>[   20.177378] RDX: ffff88824a9a4000 RSI: 0000000000000000 RDI: ffff888267fe6a30
<4>[   20.177379] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001
<4>[   20.177380] R10: 0000000000000001 R11: 0000000000000000 R12: ffffc90000cebf08
<4>[   20.177381] R13: 00000000ffffffff R14: 0000000000000001 R15: ffff888267fe6a30
<4>[   20.177383] FS:  00007f6f9c6b5e40(0000) GS:ffff888276480000(0000) knlGS:0000000000000000
<4>[   20.177384] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[   20.177385] CR2: 000000000000007c CR3: 0000000255f04006 CR4: 00000000003606e0
<4>[   20.177386] Call Trace:
<4>[   20.177390]  seq_read+0xcb/0x420

which is presumably from having no encoder attached at that time.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2175
Fixes: 8806211f ("drm/i915: Add i915_lpsp_capability debugfs")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200729130912.30093-1-chris@chris-wilson.co.ukSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

It's been a while since gen6_rps_boost() [that only worked on gen6+] was
replaced by intel_rps_boost() that understood itself when rps was
active. Since the intel_rps_boost() is gen-agnostic, just call it.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728152219.1387-1-chris@chris-wilson.co.ukSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Since we want to read the values from the HWSP as written to by the GPU,
warn the compiler that the values are volatile.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728152110.830-2-chris@chris-wilson.co.ukSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Since we use the module parameters stored inside the drm_i915_device
itself, we need to ensure the mock i915_device also sets up the right
defaults.

Fixes: 8a25c4be ("drm/i915/params: switch to device specific parameters")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728150600.4509-1-chris@chris-wilson.co.ukSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Fbc is causing random underruns in CI execution on TGL platforms.
Disabling the same while the problem is being debugged and analyzed.

v2: Moved the check below the module param check (Ville)

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716145857.6911-1-uma.shankar@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Although the WA description targets the platforms it is a workaround
for the affected PCHs, that is why it is being checked.

v2: excluding DG1 fake PCH from WA

BSpec: 52890
BSpec: 53273
BSpec: 52888
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727164729.28836-1-jose.souza@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Gracefully skip over the failures in the frequency scaling for the
moment, the results are under review.

References: https://gitlab.freedesktop.org/drm/intel/-/issues/1754Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: "Sundaresan, Sujaritha" <sujaritha.sundaresan@intel.com>
Cc: "Ewins, Jon" <jon.ewins@intel.com>
Reviewed-by: NSujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200723153805.8076-1-chris@chris-wilson.co.ukSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

After doing normal PHY-B initialization on Rocket Lake, we need to
manually copy some additional PHY-A register values into PHY-B
registers.

Note that the bspec's combo phy page doesn't specify that this
workaround is restricted to specific platform steppings (and doesn't
even do a very good job of specifying that RKL is the only platform this
is needed on), but the RKL workaround page lists this as relevant only
for A and B steppings, so I'm trusting that information for now.

v2:  Make rkl_combo_phy_b_init_wa() static

v3:
 - Minimize variables in WA function. (Jose)
 - Fix timeout duration (usec vs msec). (Jose)
 - Add verification of workaround. (Jose)
 - Fix stepping bounds in comment.

Bspec: 49291
Bspec: 53273
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-6-matthew.d.roper@intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

If HTI (also sometimes called HDPORT) is enabled at startup, it may be
using some of the PHYs and DPLLs making them unavailable for general
usage.  Let's read out the HDPORT_STATE register and avoid making use of
resources that HTI is already using.

v2:
 - Fix minor checkpatch warnings

v3:
 - Just readout HDPORT_STATE register once during init and then parse it
   later as needed.
 - Add a 'has_hti' device info flag to track whether we should readout
   HDPORT_STATE or not.  We can skip the platform/flag tests later since
   the hti_state in dev_priv will remain 0 for platforms it does not
   apply to.
 - Move PLL masking into icl_get_combo_phy_dpll() since at the moment
   RKL is the only platform that has HTI.  (Jose)

Bspec: 49189
Bspec: 53707
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-5-matthew.d.roper@intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Rocket Lake has a third DPLL (called 'DPLL4') that must be used to
enable a third display.  Unlike EHL's variant of DPLL4, the RKL variant
behaves the same as DPLL0/1.  And despite its name, the DPLL4 registers
are offset as if it were DPLL2.

v2:
 - Add new .update_ref_clks() hook.

v3:
 - Renumber TBT PLL to '3' and switch _MMIO_PLL3 to _MMIO_PLL (Lucas)

v4:
 - Don't drop _MMIO_PLL3; although it's now unused, we're going to need
   it very soon again for upcoming DG1 patches.  (Lucas)

v5:
 - Don't re-number TBT PLL and beyond, just use new RKL_DPLL_CFGCR
   macros to lookup the proper registers instead.  Although renumbering
   the PLLs might be something we want to consider down the road, it
   opens a big can of worms right now since a bunch of places in the
   code have an assumption that the PLL table has idx==id and no holes.
   Renumbering creates a hole for TGL, so we'd either need to allow
   holes in the table or break the idx==id invariant, both of which are
   somewhat invasive changes to the design.

Bspec: 49202
Bspec: 49443
Bspec: 50288
Bspec: 50289
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-4-matthew.d.roper@intel.comReviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

RKL and TGL share some general gen12 workarounds, but each platform also
has its own platform-specific workarounds.

v2:
 - Add Wa_1604555607 for RKL.  This makes RKL's ctx WA list identical to
   TGL's, so we'll have both functions call the tgl_ function for now;
   this workaround isn't listed for DG1 so we don't want to add it to
   the general gen12_ function.

Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-3-matthew.d.roper@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

RKL uses a slightly different bit layout for the DPCLKA_CFGCR0 register.

v2:
 - Fix inverted mask application when updating ICL_DPCLKA_CFGCR0
 - Checkpatch style fixes

Bspec: 50287
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-2-matthew.d.roper@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

It's silly to have if(SKL) checks in gen9_init_clock_gating() when
we can just move those bits into skl_init_clock_gating().

I'm not entirely convinced we even need this w/a, or if we do
then maybe we want it for kbl/cfl as well. IIRC it was only
listed in the wadb, but that is now dead so can't double check
anymore. Bspec doesn't seem to have any purely skl specific
DOP clock gating workarounds listed.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716190426.17047-1-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Hours Of Battery Life is a new GEN12+ power-saving feature that allows
supported motherboards to use a special voltage swing table for eDP
panels that uses less power.

So here if supported by HW, OEM will set it in VBT and i915 will try
to train link with HOBL vswing table if link training fails it fall
back to the original table.

intel_ddi_dp_preemph_max() was optimized to only check the HOBL flag
instead of do something like is done in intel_ddi_dp_voltage_max()
because it is only called after the first entry of the voltage swing
table was loaded so the HOBL flag is valid at that point.

v3:
- removed a few parameters of icl_ddi_combo_vswing_program() that
can be taken from encoder

v4:
- using the HOBL vswing table until training fails completely (Ville)

v5:
- not reducing lane or link rate when link training fails with HOBL
active
- duplicated the HOBL voltage swing entry to match DP spec requirement

v6:
- removed the optional VS 3 & pre-emp 0 from HOBL table
- changed from u8:1 to bool to store hobl_failed/active

BSpec: 49291
BSpec: 49399
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200715175637.33763-1-jose.souza@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

0x0155 is rather Ivy Bridge PCI-E Root Port.
0x0157 from the same commit ff049b6c ("drm/i915: bind driver to ValleyView chipsets")
is likely wrong too. Nowhere is it independetly confirmed or mentioned.
Signed-off-by: NAlexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428034752.3975-1-apodtele@gmail.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Rather than manually implement our own module reference counting for perf
pmu events, finally realise that there is a module parameter to struct
pmu for this very purpose.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716094643.31410-1-chris@chris-wilson.co.ukSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

The value we program to DDI_BUF_CTL changes at the following places:
- At enabling/disabling the output to configure the port width etc, and
  to enable/disable the DDI BUF function.
- At the beginning/end of link re-training to disable/re-enable the DDI
  BUF function.
- On HSW/BDW/SKL to change the voltage swing/pre-emph levels.

Except of the above the value we program to the DDI_BUF_CTL register
(intel_dp->DP) doesn't change, so no need to reprogram the register when
changing the link training patterns (which is programmed via the
DP_TP_CTL register on DDI platforms).

v2:
- Fix the commit message wrt. voltage/pre-emph level values in
  intel_dp->DP. (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-2-imre.deak@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

According to BSpec this flag should not be changed while the DDI
function is enabled. On BDW+ the DP_TP_CTL register spec also states it
explicitly that the HW takes care of enabling/disabling the scrambling
for training patterns (and it must stay enabled for normal pixel
output). Assume that this HW automatic handling of scrambling is also
true for HSW.

BSpec: 8013, 7557, 50484
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-1-imre.deak@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Explicitly check for i830 when assigning the .get_cdclk() vfunc,
and then deal with the case of not having assigned the vfunc
separately. Less confusing, and gets rid of the checkpatch complaint
about using {} on one branch but not the others.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714152626.380-3-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Some spaces have snuck in where we want tabs. Fix it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714152626.380-2-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

There's a pointless hole in struct intel_cdclk_vals, get rid of it.
Fortunately we already use named initializers so the order does not
matter.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714152626.380-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Since g4x the CFB base only takes a 28bit offset into stolen.
Not sure if the CFB is allowed to start below that limit but
then extend beyond it. Let's assume not and just restrict the
allocation to the first 256MiB (in the unlikely case
we have more stolen than that).

v2: s/BIT/BIT_ULL/ (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714201945.18959-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This reverts commit 2ddef176.

As it turned out VMWGFX needs a much wider audit to fix this.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200811092400.188124-1-christian.koenig@amd.com

The drm_mode_config_reset patches are very important fixing a recently
introduced kernel crash, the others fix various older issues which are
a bit less serious in practice.
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: "Roland Scheidegger (VMware)" <rscheidegger.oss@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200812005941.19465-1-rscheidegger.oss@gmail.com

amd-drm-fixes-5.9-2020-08-07:

amdgpu:
- Re-add spelling typo fix
- Sienna Cichlid fixes
- Navy Flounder fixes
- DC fixes
- SMU i2c fix
- Power fixes
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807222843.3909-1-alexander.deucher@amd.com

 * backmerge from drm-fixes at v5.8-rc7
 * add orientation quirk for ASUS T103HAF
 * drm/omap: force runtime PM suspend on system suspend
 * drm/tidss: fix modeset init for DPI panels
 * re-added docs for drm_gem_flink_ioctl()
 * ttm: fix page-offset calculation within TTM
Signed-off-by: NDave Airlie <airlied@redhat.com>

From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200804125510.GA29670@linux-uq9g

I need to backmerge 5.8 as I've got a bunch of fixes sitting
on an rc7 base that I want to land.
Signed-off-by: NDave Airlie <airlied@redhat.com>